How to wind a coil on a motorcycle.

How to change a trimmer line in a trimmer

Trimmer is the most common unit used to cut grass and cut small shrubs. This device is distinguished by its simplicity in maintenance, simple management during operation, and even women cope with it even a small weight. It is no secret that for the high.Quality performance of herbal mowing work, the correct selection of a cutting tool is required. As the latter in trimmers, special cutting nozzles (wheels, knives) or trimmer heads with trimmer line inside are used. Nozzles and trimmer line are a consumable tool, but if the knives can be sharpened, then when spending the trimmer line, it requires its replacement. In this article, we will tell the most detail how to replace the trimmer line correctly.

A mowing head for grass is a cylindrical case in which a coil (bobbin) is inserted with a trimmer line in it (cord). This design can be installed both on gasoline and electric trimmer. The heads differ in the method of refueling and supplying the cord and there are 3 types.

• Automatic. The cord is supplied after the user reduces engine speed. Although the automatic supply of the trimmer line is convenient if large volumes of work are performed, such rods have one drawback. A large thread consumption.
• Semi.Automatic. Using this type of head does not require complicated manipulations from the user. The principle of their operation is arranged so that the cord is automatically lengthened at a time when the device works at full speed. It is enough to slightly hit the trimmer’s head on the ground (this removes the cord lock), and the trimmer line, due to the centrifugal force, is extended from the bobbin, after which it is cut to the desired length with a knife located on a protective casing.
• Manual. For lengthening the cord, the device is required, after which the trimmer line is extended manually.

Based on the above, semi.Automatic bobbins are the most optimal option. It should also be borne in mind that the coils for the trimmer are one.Built (used only to trim the grass) and two.String, which are used to mow high grass and small, with thin stems of shrubs.

The device is in a mower

In the trimmer, the element on which the string is pulled is very simple. It is called “coil””. Usually it consists of the upper and lower part (grooves), between which a partition with a deepening passes. It is on these grooves that you need to wind the trimmer line. However, before it is extended through the recess.

Before pulling out the coil, you should twist a special button located directly on the housing of the lawn mower. Before changing the trimmer line, it is necessary to remove the coil from the mowing.

It is easy to do this, but there are features depending on the configuration of the trimmer and the coil itself.

In small electronic mowerpoints, the motor and coil are located in the lower part, and buttons are located on the sides of the bobbin. If you press them, then get the upper groove of the coil and part where you need wind up trimmer line.

In the lawnmands with a curved bar, which are not provided for a knife, the coils have special two.Horned nuts. In such tools, you need to hold the bobbin so that it does not move, and at the same time turn the nut out of clockwise. It is she who holds the whole bobin, which after that is easy to remove.

Sometimes clamps on the coil in the form of latches may occur. They must be pressed to disconnect parts of the coil. The option is also possible when the top and bottom of the bobbin are connected by thread. In this case, it is enough to take your hands on the top and bottom, and then twist in different directions until they develop.

How to tuck a trimmer line into a trimmer coil

To replace the trimmer line in the trimmer, cut a piece of material of the desired size, folding it in half. One of the halves should be 5-10 cm longer than the second.

In order to correctly wind the trimmer line on the coil, the middle of the thread, folded by a loop, you need to place in the groove of the central partition. One half of the forest is tightly wound on the upper part of the part, the second. On the lower. A longer part is wound on the bottom. Winding is carried out in the direction opposite to the direction of rotation of the head. An arrow should be drawn on the lid or side of the head. It shows the direction of rotation. It is necessary to wrap the forest in the reverse arrow direction. Do the job carefully, tightly pressing the turn to the turn.

Insert the remaining ends with a length of 10-15 cm into the slots on the upper side of the coil, this will fix them. The coil is not unwound with fixed ends.

If you do not have a trimmer line of the desired length, you can wind the forest with more than one piece, but two. In this case, bend the end of the forest with hook and insert it into the slot of the central partition of the bobbin. Do the same with the second piece. Now wrap first a piece first, and then the other to your half of the coil against its direction of rotation.

To tie a trimmer line into a trimmer, insert its ends into the holes of the mowing head and pull them out. Plant the coil on the axis and push down so that it sat in its place, and again pull the ends of the cutting thread to pull them out the entire length.

The ends brought out should almost reach the protective casing. Cut the excess. To do this, you can use the steel plate installed on the casing, which plays the role of a knife and automatically cuts off the trimmer line of excessive length when promoting the head.

Bobina closes with a protective lid. Put it in place and press it down to the click that the latch will be published by falling into the grooves. Always check whether the cover has stood on the trimmer and whether the latches snapped, otherwise it may jump off during operation. In this case, the reel will throw the reel force.

Do not try to wrap the material as much as possible. In this case, the coil may not fall into place and there will be problems with the installation and fixation of the lid. It is better if the coil is filled with wood so that it does not go beyond the dimensions of the details.

In addition to mechanical braids with two blades, there are also models with one. Their differences are that the cutting thread is displayed only on one side. The coil in such versions of the braid may not have a central partition, instead of it, a slot in the lower side is used to install a non.Working end of the thread, there is also a slot for fixing the working end in the upper.

With a replaced forest, you can start work. Do not mow thick weeds and branches of the shrub. This is not work for a braid. In order to avoid injuries and a break in the forest, make sure that stones and branches do not fall under the braid.

To download the lawn of one refueling coil with a reinforced trimmer line is enough for an area of ​​400-600 m2.

After the cutting thread as a result of the work is worn out, turn off the braid and remove the lid on the mowing head. Pull out from the slot of the forest, stretching it to the desired length, and insert it again in the slot. The amount of material wound on the coil is enough for 5-10 cycles of work depending on the model of the device. When you install the lid in place, carefully look at whether the grooves were clogged where the latches are inserted, if they are clogged, then carefully clean them.

How to test motorcycle pickup coils

When the trimmer line is worn out, you need to disassemble the braid head again, pull out the coil and wind up the work trimmer line on it again.

How the head with a trimmer line on a motorcycle works why you need to know the principle of work

Depending on the manufacturer, the heads differ structurally not only externally, but also inside. Most drums have a clamping spring inside (semi.Automatic and automatic). The instruction is presented above how to disassemble the head of the trimmer without a spring, t.E. On a manual.Type head. The principle of dismantling a semi.Automatic head with a spring inside almost identical above described instructions.

The principle of operation of the semi.Automatic coil of the trimmer is as follows:

• Inside the head is a coil, which is planted on slots that prevent its free movement
• The coil is affected by a spring that presses it to the slots located in the design of the cover
• The trimmer line, the length of which depends on the instrument itself. Usually this length is from 1 to 4 meters
• During the work, if it is necessary to increase the length of the trimmer line, the protruding part of the drum occurs, through which it comes out of the hook with the slots. In this case, the trimmer line is wound from the drum, increasing in the length
• Having released the required amount of trimmer line, you should release the pressing, and continue to perform work on the injection of the grass

The advantage of the tool with a trimmer line is that this consumable does not require sharpening compared to metal disks. In addition, if a stone or tree comes across the way, then the trimmer line simply breaks down, without having a negative effect on the gearbox and the engine engine, as is the case in the case of metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to proceed to the consideration of the process of refueling the trimmer line into the coil of the trimmer. After all, it is precisely this moment that most owners of the Special Instruction causes difficulties.

Preliminary preparation

First of all, to wind the trimmer line, it is required to remove the coil (bobbin, spool) from the trimmer. Specific actions will depend on the complexity of the configuration and the type of product itself:

• Small electric trimmers with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the trimmer line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
• Electric and gasoline trimmers with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a motionless position with one hand, and rotate the fixing bobbin on the bar with a barack’s bar with one hand. After disconnecting the nut, the whole bobin is removed.
• Electric and gasoline trimmers with the ability to install a knife on a straight rod (for example, trimmers of calm) under the bobbin have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Video: how to wrap a trimmer line on a benzo

How to remove a trimmer coil?

To replace or wind the cutting thread to the coil, it must be removed.

The complexity of its removal depends on the model of the tool:

• Low.Level tool. Motor almost from the ground. To remove the coil, press the buttons on the side of the trimmer. When you press these buttons, the case opens, in which the coil is located.
• Curved trimmer. Here you must turn a special lamb counterclockwise. After that, the coil and the spring in it are removed.
• Direct toolbar. The bar is held with a screwdriver or other object. The turn clockwise will remove it. Then they disassemble the tool to parts and remove the coil.
• If you use one antenna tool, you will need about four meters of thread. This thread is inserted into the hole inside the coil, where it can be fixed. Then one end of the line was directed in the direction of the arrow. Then the end of this thread is fixed in the groove, which is in the coil. This is necessary to prevent unwinding the thread when assembling the coil. In the absence of grooves, you must adhere to the hair growth line and collect the coil.
• When using a dual antenna tool, you must first check the number of available grooves.

If the coil is equipped with a semi.Automatic mechanism, wrap the wire as follows:

• The thread goes down into the hole that is inside;
• Fasten the ends of the thread in the grooves on the case.
• The coil is collected and pressed by a special button;
• After that, the trimmer line itself begins to wander in the right direction.

You should always remember that the cutting thread should be protected from solid objects. It will extend his life.

If you do not follow this rule, you often have to stop working, remove the coil and change the thread to the new.

Coils with carvings with various types of bobbins

With two.Row automatic heads:

You must first press the clip until it clicks, remove the lid.

Carefully turn the coil so that it can disconnect from the holder. Please delete it.

Measure two pieces of rifled thread of the same length

To facilitate further work, the ends of the hairline must be cut at an angle. Take one end and insert it into a special hole in the coil. It can also be slots, grooves, clamps and much more.

Further, in the direction of the arrow, you need to wind it, and quite tightly and evenly. A special ear on the coil needs to fix the end of the hair growth line.

The second half of the line is subjected to the same operation, only on the other half of the coil.

Then insert the coil into the head of the trimmer. And the rest of the hairline down the hole in the head.

Then carefully straighten the thread and close the lid. If the hair trimmer line is long, it is better to reduce the excess. About fifteen centimeters should remain on each side.

• The thread goes down into the hole that is inside;
• Fasten the ends of the thread in the grooves on the case.
• The coil is collected and pressed by a special button;
• After that, the trimmer line itself begins to wander in the right direction.

It is necessary to carefully and carefully insert the cutting thread into the car, since not only the purity of the garden plot depends on the correct winding of its winding, but also personal safety.

How to wind a trimmer line on a trimmer reel: Key points

A gasoline or electric trimmer is an indispensable assistant in the arsenal of a modern summer resident or owner of their own home.

Thanks to these garden devices, you can easily bake even a large personal plot.

After acquiring this tool and performing several mowing, many people think about how to correctly wind the trimmer line on the coil of the trimmer.

For an inexperienced user, the first operation to replace it will seem problematic and laborious, since the developers often do not fully reflect the instructions for replacing the trimmer line in the operating manual.

Preparation for the winding of the trimmer line

Previously, before the winding process, it is necessary to remove the coil with a trimmer line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three structural types of trimmers:

• Compact trimmers with electric drive. Electrimmer coil A tool of this type has the lower location of the engine and head, which in turn has two side buttons to dismantle the bobbin. With the simultaneous pressing of them, the upper part of the coil with a trimmer line is disconnected, and the lower remains tightly attached to the spit. Experts recommend disassembling on a flat site in order to prevent spring popping up.
• Moto and electric ships with a curved duralumin rod not designed to work with a knife. As a rule, coils of such models are equipped with a special barashka nut. The dismantling of the spoon should be performed by holding the coil body with one hand, and the second to twist the lamb counterclockwise.
• Powerful benzotrimers and electric cos with a direct bar. Trimmer with a straight bar Such a model provides for the possibility of installing a knife. Removing the coil in such models is carried out by means of two keys drowned in the case. To install a trimmer knife, it is necessary to combine the hole of the bobin and rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the case is easy to unscrew with your hands clockwise.

Trimmer line on trimmer

The measured and neat dismantling of the spit of the braid coil makes it possible to go directly to the winding of the trimmer line.

Design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used.

Today, there are several varieties of coils depending on the number of antennae antennae and refueling methods:

Trimmer coil with one osmus

Many owners and experts note the simplicity of the operation and refueling of bobin with one mustache. Depending on the manufacturer, the length of the refueling trimmer line can range from 2 to 5 meters.

The end of the trimmer line is inserted into the head in a special technological groove or hole, and the winding is carried out in the reverse work rotation of the bobbin side.

On most coils on the outer side of the case there are marks in the form of arrows that indicate the directions of the movement of the trimmer bobin.

After winding, you need to leave the free end of 15-30 cm to strengthen the centrifugal force, which is determining when extracting a trimmer trimmer line in automatic and semi-automatic reels. The left end is extended through the coil work hole and make the head assembly.

Trimmer head with two antennae

After extracting the spray from the coil body, we determine the number of streams for winding trimmer line (1 or 2).

There is no fundamental difference between bobbins with one and two grooves, but with a careless refueling in a paired groove, there are problems with operation.

Due to the likelihood of weaving neighboring tools, a situation may arise when after the wear of the working antennae it is impossible to extract new.

Regardless of the number of streams for refueling, a trimmer line is taken from 1 long.5 to 3 meters. The winding must be carried out in reverse rotation of the head to the side, since the winding in the direction of movement will lead to the fact that the trimmer line will not be removed from the bobbin.

After the trimmer line is tucked into the coil of the trimmer free ends (15-30 cm) we extend into special holes. Next, collect the head in the reverse disassembly order and check the performance.

Do not worry if the ends of the two antennae are very different in size, because when the trimmer is launched, the knife installed on protection will cut off the excess.

Trimmer head with automatic line dressing

In some models presented on the market, a coil with an automatic winding mechanism is installed. It is enough to correct the owner and fix the ends in the head, and the winding operation will perform the tool itself when included in the operating mode.

It is almost impossible to incorporate the trimmer line into a trimmer with such a head, since the coil independently determines the position of the antennae.

The advantages of the automatic head of the trimmer include the simplicity of trimmer line refueling, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

How to wind a trimmer line on a trimmer reel: Key moments WAS LAST MODIDID: June 28TH, 2018 BY Administrator

How to wind a trimmer line on a trimmer reel. We master step by step

To find out how to wrap the trimmer line on the coil of the trimmer, you need to carefully examine the braid part of the device or look into the tool passport. The fact is that, depending on the method of refueling, trimmer coils are quick.Charged and collapsible. For the former, everything is very simple. You don’t have to remove and disassemble anything, you just need to find holes for the trimmer line, pass it through both ears and wind the right number of turns, and cut off the excess.

• First, make sure that the trimmer is turned off, and if you use a benzo.Coat, be sure to unscrew the candle.
• Remove the mowing head from the trimmer and disassemble it. To do this, click on the latches located on the head of the head and remove the lid.
• Cut the required amount of trimmer line, and make it sharp. This will facilitate the work.
• Place one end of the trimmer line in a special clamp located in the center of the coil.
• Screw the string in the direction of the arrow indicated on the lid, while tightly hold the thread with your finger.
• Leave the free end of 12-15 cm long and fix it in the slot on the coil.
• If your trimmer’s spike coil is two.Section. Do the last 4 points again. At the same time, wind the trimmer line in the free section. And fix the end on the other side of the coil.
• Return the structure to the mowing head and through special slots pull the free ends of the trimmer line.
• Close the head cover and collect a trimmer. Your braid is ready for work again.

How to wind the trimmer line on the coil of benzos: how to wind the trimmer line on the coil of a gasoline and electric trimmer

This video lesson shows in detail how to wrap a new trimmer line on a trimmer or motorcycle. For convenience, unscrew the mowing head. For clarity and convenience. Remove in the direction with a given arrow. First open the head. There are latches on the sides here. There are 2 of them. You can take it off with your hands, but if it does not give in, use the screwdriver. The design consists of 2 parts. Head, spring on which the winding of the trimmer line is performed. Lid. Some of the button are inserted separately.

If we talk about the principle of work, there is nothing complicated here. The lid has clamps. The coil in the assembled position is pressed by a spring. Fixators do not allow to turn. Click on the button, the coil is slightly lifted, turned to several revolutions or half a turn, while the trimmer line is supplied out. Release the button. The coil is again fixed until you need to release a new trimmer line again.

As for the choice of trimmer line diameter. On some coils, information is written. There is a hole for trimmer line with a diameter of 1.6 mm, 3-3.3. 2 or more millimeters. If the information is not indicated, determine the maximum permissible diameter, taking the head and extinguishing the trimmer line into the final hole. Pay attention to the instruction manual of the trimmer.

Two methods are used in the coil sample. In the side, which divides it into two parts, a slot was done until the end. Put a trimmer line in it. We determine the required amount by wound on one of the parts of the coil. The length should not go beyond. In this case, a piece of about 4 m of trimmer line with a diameter of 3 mm is required. Smaller diameter will need more.

Fold the cut piece in two. We release one end a little longer-10-15 cm. Bend more. We find a slot on the coil and start a loop there. A very important point. There is a Wind Line inscription. The direction of winding is indicated. If this is not found, then look at the arrow indicated on the mowing head and wind the trimmer line in the opposite direction.

Continuation on the video “Hotsem” from the fifth minute.

Owners of private houses know how necessary such a type of tool as a trimmer is. It can be gasoline and electric, and they differ in the design of power units. For injection of grass in areas where there are stones, trees and other obstructing objects, trimmer line is used as a cutting device. This consumable in the process of use wears out, therefore, how to wind the coil of the trimmer, we will consider in detail in the material.

What you need to know about the trimmer line on the trimmer

Fishing lines is called consumable, which consists of nylon, and serves as a cutting device. Through this equipment, the grass grows, which is ensured due to rotation of the instrument head with a high frequency. This material has a different thickness, which depends on its use on the corresponding tools of low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with motorcycles (from 2.4 to 3. 2 mm).

The more powerful the tool, the accordingly there should be a cutting equipment. This affects not only the quality of the injection of grass, but also on the life of the material. If you ask the question of how to wind a trimmer coil, then it’s time to change the reload of the tool. With the onset of spring, this issue is becoming more and more in demand, so it’s time to understand the step.By.Step instructions for replacing the trimmer line in the coil of the trimmer.

How to remove a coil from a trimmer and extract a trimmer line

Initially, before filling the trimmer line into the coil of the trimmer, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum. The heads are of different types (depending on the manufacturers), however, the principle of replacing the trimmer line on the coil has the same. First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a trimmer line from it.

Instructions on how to promote a hand head on a trimmer, has the following look:

• Turn the instrument with the head to the top, and if necessary, cleanse it from pollution. Take two fingers of one hand by the cover of the cover (on the mowing head), which are located symmetrically to each other. After a light pressed inward, dismantle the protective cover from the drum
• Next, from the rampart of the drum, the coil for the trimmer line should be removed. It is planted on a shaft without fasteners, so it is dismantled with one hand
• The main part of the drum is fixed using a screw, which must be twisted with a screwdriver with an appropriate tip or a bat
• To twist it, it is necessary to hold the base of the drum with one hand, and the second to remove the screwdriver against the direction of the clockwise
• After that, you can proceed to dismantle. To do this, you do not need to pull it with all your strength, but slightly shaking it, slowly remove it from the hook with a metal shaft on which the drum is planted

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

• It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
• If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
• When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
• If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
• There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Preparation for the winding of the trimmer line

Previously, before the winding process, it is necessary to remove the coil with a trimmer line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three structural types of trimmers:

Motorcycle Coil Testing: The Basics

Such a model provides for the possibility of installing a knife. Removing the coil in such models is carried out by means of two keys drowned in the case. To install a trimmer knife, it is necessary to combine the hole of the bobin and rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the case is easy to unscrew with your hands clockwise.

How to wind a trimmer line on a trimmer reel

A gasoline or electric trimmer is an excellent assistant in the processing of a garden plot. But, like another technique, requires attention and a certain care.

Unfortunately, equipment developers do not give complete instructions on how to wind the trimmer line on the coil of the trimmer. In this connection, the owners of motor vehicles have many questions.

In this article, we will examine in detail various examples and methods of winding trimmer line on the reel.

How to wind a trimmer line on a trimmer reel. Preparation

The trimmer coil is located in a mowing head, which consists of a spring, coil and two lids.

• The first action must be disassembled and the head of the trimmer. To do this, click on the locks until the faces located on the sides of the case, and turn clockwise.
• To open the mowing head, click on the side latches, if it doesn’t work out with your hands, you can use the screwdriver. Remove the coil.
• For the correct choice of trimmer line suitable for your trimmer, look on the inside of the digital designations. These numbers indicate the necessary diameter of the trimmer line in millimeters.
• If you did not find such information, then the maximum diameter can be determined by taking the trimmer line and put it on the hollow hole. The thread should go back and go.
• There are two ways to wind the trimmer line, we will consider each of them in detail.

How to wind a trimmer line on a trimmer coil. 1 method

Scroll about 4 meters of trimmer line for winding. To determine the exact amount of the right material, wrap the trimmer line from the roll to the coil, the final result should not exceed the diameter of the coil and get out by the edges.

• For ease of work, fold the thread in half, one end make it longer than the other by 10-15 cm.
• There is a dividing side on the coil, passing in the center. It has a cavity where you need to insert a trimmer line. To do this, squeeze the flexion place of the thread more and make the loop into this cavity.
• Important. You need to determine exactly which direction to wind the trimmer line, for this, find the “Wind Line” inscription on the coil, there is an arrow that indicates the direction of winding near it. If there is no such arrow on the coil, look for the arrow on the body of the mowing head, it is necessary to wrap it in the opposite direction.
• Wrap the trimmer line on the coil carefully, pulling the thread as much as possible.
• At the end of the work, take an end that is shorter and insert it into the blade on the coil body corresponding to the diameter of your trimmer line. In this paper, the thread was put into the blade with designations 3.3 mm.
• With the second end, do the same, but insert it into the blade of the opposite of the previous. Fix the two ends, leave the allowance 5-10 cm, cut the rest. Allowances are necessary so that when inserting the coil into the head, the thread does not unwind.

How to wind a trimmer line on a trimmer coil. Assembly

• Insert a reel with a wound trimmer line into a mowing head, pull the thread from the side blades and tighten.
• Fix it tightly and close the top tire on top, connecting two parts with snapping.
• Before inserting into the trimmer, slightly cut the ends of the thread, in order to avoid knocking on a protective casing.

How to wind a trimmer line on a trimmer coil. The second method

Methods differ in winding. In the second method, use the trimmer line two pieces individually. At the end of the thread, make a bend of the bracket, as shown in the photo, and drive into a fixation hole. Wrap two coil blades in this way.

• If you have a coil with one blade, find a hole in the inside to fix the trimmer line. Insert the trimmer line in one of the methods given above. Then wrap it to the reel, in the direction of the reverse movement of the coil on the trimmer. Leave a small section of the thread and conduct the assembly of the mowing head.
• When you run the trimmer into the work, the excess part of the trimmer line will cut off the sharp blade of trimming on your own.
• In order not to change the trimmer line too often, constantly stopping the work, try to avoid contacting equipment with solid items while using.

How to remove a coil from a trimmer and extract a trimmer line

Initially, before filling the trimmer line into the coil of the trimmer, it is necessary to extract it from there. Coil or tip is a device that is located inside the braid, bobbin or drum. The heads are of different types (depending on the manufacturers), however, the principle of replacing the trimmer line on the coil has the same. First of all, we will figure out how to remove the head from the tool, as well as how to get a drum with a trimmer line from it.

It is interesting! The replacement of equipment can be done directly on the tool, but if you do it for the first time, it is still recommended to remove the head, and study the detailed process of winding. After the technology is mastered, you can perform work on replacement on a trimmer of a motorcycle or a gas station.

Instructions on how to promote a hand head on a trimmer, has the following look:

• Turn the instrument with the head to the top, and if necessary, cleanse it from pollution. Take two fingers of one hand by the cover of the cover (on the mowing head), which are located symmetrically to each other. After a light pressed inward, dismantle the protective cover from the drum
• Next, from the rampart of the drum, the coil for the trimmer line should be removed. It is planted on a shaft without fasteners, so it is dismantled with one hand
• The main part of the drum is fixed using a screw, which must be twisted with a screwdriver with an appropriate tip or a bat
• To twist it, it is necessary to hold the base of the drum with one hand, and the second to remove the screwdriver against the direction of the clockwise
• After that, you can proceed to dismantle. To do this, you do not need to pull it with all your strength, but slightly shaking it, slowly remove it from the hook with a metal shaft on which the drum is planted
• When installing the installation, the head should be planted in a tetrahedral slot

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how replacement is performed. When dismantling, consider the following nuances:

• It is recommended to remove the head periodically to prevent the corrosion of the threaded connection. If you never unscrew the screw, then if necessary to do it will be difficult and even sometimes impossible
• If the screw has a tetrahedral boring of the head, then for twisting you should select a screwdriver or bit of a suitable size to eliminate the licking of the faces on the head
• When assembling the installation, a threaded seat should be treated with lubricants, for example, solidol or machine oil
• If the edges on the screw are licked, then for its unscruptions you can use special clamping forceps
• There are drums that do not require preliminary disassembly. To dismantle them, you should take up it, and rotate in the opposite direction of the direction of the clockwise

Knowing how to disassemble the drum, you should continue to clarify the process of replacing the trimmer trimmer line. Below the video shows a detailed process how to open a trimmer coil and disassemble it.

Block: 3/8 | Summer characters: 2920Source: https: // moiinstrumentu.Ru/uchimsja-pravilno-namatyvat-lesku-na-katushku-trimmera-i-benzokosy-instrukcija-po-ubanovke.HTML

How to wind a trimmer line on a trimmer reel. We master step by step

To find out how to wrap the trimmer line on the coil of the trimmer, you need to carefully examine the braid part of the device or look into the tool passport. The fact is that, depending on the method of refueling, trimmer coils are quick.Charged and collapsible. For the former, everything is very simple. You don’t have to remove and disassemble anything, you just need to find holes for the trimmer line, pass it through both ears and wind the right number of turns, and cut off the excess.

But on the second option it is worth stopping in more detail, because the coil will have to be dismantled and disassembled.

• First, make sure that the trimmer is turned off, and if you use a benzo.Coat, be sure to unscrew the candle.
• Remove the mowing head from the trimmer and disassemble it. To do this, click on the latches located on the head of the head and remove the lid.
• Cut the required amount of trimmer line, and make it sharp. This will facilitate the work.
• Place one end of the trimmer line in a special clamp located in the center of the coil.
• Screw the string in the direction of the arrow indicated on the lid, while tightly hold the thread with your finger.
• Leave the free end of 12-15 cm long and fix it in the slot on the coil.
• If your trimmer’s spike coil is two.Section. Do the last 4 points again. At the same time, wind the trimmer line in the free section. And fix the end on the other side of the coil.
• Return the structure to the mowing head and through special slots pull the free ends of the trimmer line.
• Close the head cover and collect a trimmer. Your braid is ready for work again.

Apparently trimmer heads

Takozhdov Budov can be the mats of Kosi: with the auto.Deed of the hairy, prickly manual. At the Pershom Vipad, the poddzhzhit of the robochi kintsi, the trookhi trookhi. And if you see the dodast, the hair is automatically. For napiwavtomatical molesters, on the special button on a special button, Shcho is known below. Termmer at the Tsoma Vimikati Nobov’yazkovo. Get just knock on the scoop about the ground. NUBILSH NAVENICE in Roboti. Trimerus with manual feed string. Schob Poddzhita ї Robochi kintsi, iztrument notly vimknuti і Zrobit to the operation.

Shche Kotushka Zwinnnya for Trimmer Buvaє:

• One.String. Piring tilki for cosmetic trimming of the attachment of the tier;
• Two.String. Stall for Bilsh Seryoznich Robit for cleaning the Dlyanka vid Travi.

Yakshcho Vi, without growing up, got a trimmer with a single.Sectioned squel, roded in the nomo і podumu buy novelties. Do not ripen. One.String trimmer can be re.Tuned to the yard, Vesashi Deaki Zmіni in structures:

• With a thin, ale of the mitzny plasticity, Virizati Kilza, the in.Reservoir di.Aeter of the yogo is guilty of a boti cerses, and calls the yaku, and calls. Diameter Kotushki.
• On the inside of the part of the Kiltsiy, the little vihimka is in the way, through the yak there is a thread.
• Dali kilze rosriza, get on the cat. And the Mass Rozriza is stabbed to the tape of Abo is soldered behind the pre.Person of the Garyacho knife. Axis I all. Now the Kinets hairy can be wrapped on its part of the cat.

Apparently trimmer heads

Takozhdov Budov can be the mats of Kosi: with the auto.Deed of the hairy, prickly manual. At the Pershom Vipad, the poddzhzhit of the robochi kintsi, the trookhi trookhi. And if you see the dodast, the hair is automatically. For napiwavtomatical molesters, on the special button on a special button, Shcho is known below. Termmer at the Tsoma Vimikati Nobov’yazkovo. Get just knock on the scoop about the ground. NUBILSH NAVENICE in Roboti. Trimerus with manual feed string. Schob Poddzhita ї Robochi kintsi, iztrument notly vimknuti і Zrobit to the operation.

Shche Kotushka Zwinnnya for Trimmer Buvaє:

• One.String. Piring tilki for cosmetic trimming of the attachment of the tier;
• Two.String. Stall for Bilsh Seryoznich Robit for cleaning the Dlyanka vid Travi.

Yakshcho Vi, without growing up, got a trimmer with a single.Sectioned squel, roded in the nomo і podumu buy novelties. Do not ripen. One.String trimmer can be re.Tuned to the yard, Vesashi Deaki Zmіni in structures:

• With a thin, ale of the mitzny plasticity, Virizati Kilza, the in.Reservoir di.Aeter of the yogo is guilty of a boti cerses, and calls the yaku, and calls. Diameter Kotushki.
• On the inside of the part of the Kiltsiy, the little vihimka is in the way, through the yak there is a thread.
• Dali kilze rosriza, get on the cat. And the Mass Rozriza is stabbed to the tape of Abo is soldered behind the pre.Person of the Garyacho knife. Axis I all. Now the Kinets hairy can be wrapped on its part of the cat.

Can you make a trimmer coil with your own hands

On sale there are a large number of trimmer heads (not automatic), which have a low price and good quality. But sometimes situations arise, for example, in the country, when the trimmer coil broke, and its repair is impossible, the store is far away, and you need to mow. In this case, you can quickly, literally in a few minutes, make a simple trimmer nozzle to fix the trimmer line from ordinary plywood 10-12 mm thick.

• Take a piece of plywood or textolite and draw a circle with a diameter of about 14 cm on it.
• Cut the disk with a jigsaw or hacksaw for metal.
• Drill a hole in the center of the disk, suitable in diameter to the gear shaft. Do not forget before installing a disk on the shaft, put a puck on it.
• You can fasten small corners along the edges of the disk or make 1-2 holes on the opposite sides. They will serve for refueling fishing lines in them.
• To fix the trimmer line, you can screw several screws into the plywood.

Such a home.Made mowing nozzle is fixed on the shaft With a nut. Twist or unscrew the nut without fixing the shaft will not work. To replace the cord, it will be enough to release the screws, insert a segment of the trimmer line of the required length and press it again.

Also, a mowing nozzle for fixing the trimmer line on it can be made from a metal sheet. How to do this can be understood from the next video.