Replacing the omentum on the Patriot trimmer. Popular materials

Repair of benzos, gasoline trimmers

In order for the lawn mower to work properly and serves you for a long time, it is necessary to conduct a regular technical inspection, during which existing breakdowns or malfunctions can be detected, as well as those that may occur during future operation.

The consequences of the failure of the lawn mower can be different: from the replacement of a hand starter, to wear of the connecting rod piston group. At the same time, it must be understood that the cost of repairs can be completely different, and sometimes unprofitable.

The specialists of our service have a lot of work experience, so they serve all the well.known brands of benzosos. They cope with the tasks of any level of complexity, quickly reveal the cause of inoperability and quickly eliminate it.

For high.quality diagnosis and subsequent repairs of the benzotrimer, the use of special equipment is required, so we carry out its maintenance in our service zone.

In the diagnosis, we check not individual problem nodes and mechanisms, but carry out a thorough diagnosis of the entire benchinated tool in order to understand the profitability of the repair.

Our competitive advantages

Mtd, Husqvarna, Caiman, EFCO, Champion, Bolens, Solo, Oleo-Mac, Stihl, Echo, Honda, Partner, Patriot, Stiga, DDE, as well as the repair of Chinese trimmers.

How to prepare a high.quality fuel mixture

• Gasoline is poured into the container to the corresponding mark.
• Oils for gasoline, and not vice versa, flows oil for a two.stroke engine to the level
• The mixture shakes it several times until uniform.
• If a special container is not provided in the configuration, use the usual gasoline canister. Make a mixture in this ratio of gasoline/oil 32: 1.
• To prepare a mixture directly in the fuel tank of a trimmer for grass is not recommended.

Removing the crankshaft bearing

Now consider how to remove the crankshaft bearing. There are two options:

• To extract the part, you can make a hook with your own hands. To do this, you need a piece of rod about 400 mm long and with a diameter of 6 to 8 mm, as well as a metal cylinder with a through hole, the diameter of which is greater than a rod.
• retreat 10 mm from the edge of the rod and bend this small edge at an angle of 90 degrees;
• put on the cylinder on the rod;
• At the other end of the rod, fix the segment so that the T-shaped ending is obtained.

To extract the bearing, you need to insert a metal rod into its clip and hook the part with a manufactured bend. Knocking on the T-shaped ending and with each blow, turning the rod, you can pull out the desired part.

• If you do not want to make a device or you do not have suitable materials, you can remove the bearing from the crankshaft using a bolt or metal cylinder with a diameter of 14.5 mm. You need to choose a bolt and cylinder so that they enter the hole with a small margin in diameter. not very free and not very tight.
• First you need to pour solidol or other lubricant into the space behind the bearing through the corresponding hole;
• The cylinder or bolt is first inserted into the inner clip, and then clogged to the stop;
• As soon as the rod completely enters the hole, add more lubricating fluids;
• Due to the large amount of lubrication and pressure of the rod, the bearing will come out of the crankshaft nest.

How to assemble a gasoline trimmer for grass Patriot Pt 3055

• The fastening screw is twisted with a small effort. Cable clips on the handle are attached.
• The shoulder belt is snapped by a carbine for a special fastening on the main rod of the unit.
• To the lower part of the bar, at the base, a metal casing is screwed onto the protective case of the gearbox, and a plastic casing is attached to the top to enhance protection.
• A protective flange is installed on the slotted gearbox with the coincidence of technical grooves on the gearbox with flange.
• A fixing rod or hexagon is inserted between the gearbox and the flange.
• The trimmer head is twisted to the stop, against the course of the time of time.
• A cutting knife is installed on a protective flange.
• A knife is pressed with a puck and twisted by a nut to the stops against the course of the clock.

If the knife is stuck on one side, then it is turned over and use the second sharpened side.

• Both parts of the rod are connected using a fixing lever of the fastener system.
• Checking the correct assembly: the impossibility of opening without pressing on fixing fasteners.
• The additional mounting of the coupling of the connection is tightened to the stop. This gives an advantage when using the unit to perform different works: the lower rod is installed on fixed angles of 90 and 180 degrees.

How to change the starter cord?

It happens that in the impossibility of starting a starter is not a spring to blame, but the cord itself. He can seize or completely break. Dismantling the starter of the lawn mower or trimmer for grass is universal in its steps.

• Remove the starter block from a trimmer for grass or lawn mower.
• Unscrew the main bolt holding the handbrake.
• Pull the coil and melt the remains of a worn cord from it.
• Unscrew the knot on the handle of the cord and pull its end from it.
• Untie the knot at the other end (at the beginning of the coil) and remove the old cord. The nodes that have become tight are unleashed with pliers or ticks.
• Tie a knot on one of the ends of the new cord, prone it through the hole at the beginning of the coil (closer to its axis).
• Shin a few turns of a new cord to the coil. If it is long, then cut the excess.
• Season and soak the spring tensioner (if it starred) and spring.loaded elements in the correct sequence.
• Put the coil in place and take the free end of the cord to the outlet of the starter and in the handle.
• Install the starter block in place.

Twist the starter by the cord, start the engine of the lawn mower or a trimmer for grass. The larger and more powerful the engine, the more cord jerks will be required when starting, the norm is no more than 7 times. The result is a quick and smooth launch of the motor, the readiness of the unit for work.

Repair of the starter of the gas trimmer for grass may be needed at the most inopportune time. At the same time, there are two ways to solve the problem: replace a broken part or replace the entire assembly. The last option will cost more. In most cases, only a screwdriver with a tip is required to repair the device with your own hands. Repair does not take much time and does not require special knowledge. To achieve the desired positive result, it is enough to know the device, the principle of operation, the nuances of the assembly-disassembly of the starter for the trimmer for the grass.

The device and principle of the starter on the trimmer

Gas engine. This is mainly the main part of the brush. Its power lies in the range of 0.5-2.5 liters.With. Movement from it is transmitted to the shaft located inside the hollow rod, and then through the gearbox, consisting of gears, already stabbed or knife (working body).

Bigorezes also have the following elements:

• Corrugated board;
• lever arm;
• belt designed for simplicity of use;
• Starter used to launch an internal combustion gasoline engine.

The starter of the trimmer for grass is an integral part of the engine start. This is shown separately in two photos below.

Starting mechanisms for different models of gasoline braids work according to the same principle: when starting an internal combustion engine, the tongues indicated by the number 1 in the photo above are hooked by dogs 3. When the engine is launched, they return to the previous position due to centrifugal force. A similar role is played by wires 2.

The process of returning to the initial position of the elements of the mechanism is due to the presence of a spring wound around the axis. It turns around when the rope is pulled. After the release of the cord, it is pulled and wound with a spring assembly. When the internal combustion engine is launched, the trigger rotates its shaft until it starts to work.

Today, gasoline scooters are equipped with two types of starter mechanisms:

The first option is much more common.

The trimmer starter for grass can work without breakdowns for a long time. It is impossible to clearly indicate a continuous period of time. Everything is determined by the initial quality of the device and compliance with the rules of its operation.

The main malfunctions of the trimmer for the grass of the starter

It is easy to determine the reason for the refusal of the starting device. There are several main options:

Perhaps the starter mechanism is accidentally broken. The consequences will be deplorable if the wrapped cable is wrapped around the flywheel of the internal combustion engine: then the spring will burst and the pulley will break. But such cases when a complete replacement of the starter is required are extremely rare. In most cases, it is enough to fix a new spring or replace the cord to fix the mechanism.

How to disassemble a trimmer for grass Patriot Pt 3055

Everything is just done: install a knife and a fishing line for a trimmer, and it is very convenient to quickly remove / install a USB flash drive. And in general, the fact that the collapse is collapsible. It is very convenient to wear a trimmer for grass.

This year he was retired, worked for 10 years without problems. Accept, you will not regret. Price and quality unlike other companies

Cheap, works well on ordinary and fresh fuel, easy to use.

A woman without technical training gathered, refuel and went to mow!

Having bought it, I was happy, and in the first season since August mowed low grass in the country.

price, you can serve yourself, everything is simple. every year at the end of the season.

The advantages are the same as more expensive manufacturers! Invalious set, ease of maintenance, convenient belt with a handbag!

It is difficult to run. You need to do so much: first press the button several times to fill the oil in the carburetor, then turn on the start button, remove the starter, run, squeeze the clutch and throttle, and then press another button. In general, for a woman a difficult set, I want one button. and right away) apparently, other manufacturers are somehow easier, but I have nothing to compare with.

The engine is weak, if you mow high grass, wind

It is not clear that I begin to mow, the engine is gaining momentum to the limit (the sound in the gap is clean), then the speed seems normal, and the coil with the fishing line barely rotates

He is too weak for mowing weeds and copes poorly with large areas. But with a small area, he copes with the raid.

Disgusting belt, I had to adapt from the old Husqvarna.

And then the twine for the starter did not return to the end. And this year does not return at all. Something with a spring. This is impossible to do

Unsuitable belt for socks. unusual over the shoulder with a hard edging. Constantly slopes out of metal holders (spins like a worm). High noise. A capricious to gasoline, an oil tank with a low m of a fat disappeared (and not tight, a year later the lid of the fuel tank exploded), and the power was not like that, it added another 95, and it burned down. The piston burned. Pour 92 o. I will not change the rings. Repair is like a new braid. Weak grip after several strokes on the fence with a metal disk. Strength fell when he began to scroll a little.

Pros: Elk. Inexpensive. Knife and fishing line for a trimmer are included.

Cons: hard to run. You need to do so much: first press the button several times to fill the oil in the carburetor, then turn on the start button, remove the starter, run, squeeze the clutch and throttle, and then press another button. In general, for a woman a difficult set, I want one button. and right away) apparently, other manufacturers are somehow easier, but I have nothing to compare with.

I worked seven seasons, no operating problems, I did not start this spring after winter. The diagnosis showed a decrease in compression. I made it out and found out that the compression ring was lying. He cleaned the ring and piston and collected it. It begins better than a new. She has already paid 100 times for this price. Take Patriot and don’t be shy.

Disadvantages: the engine is weak, if you mow high grass, wind

Advantages: everything is simply done: installing a knife and fishing line, and it is very convenient to quickly remove / install a flash drive. And in general, the fact that the collapse is collapsible. It is very convenient to wear a trimmer for grass.

Disadvantages: the size of the knife could be increased, but perhaps its power did not stretch. not critical, but the smaller, the easier it is to mow weeds (the easier the trimmer for the grass). This does not always begin the first time. Although maybe it’s my hands))). The belt is simple over the shoulder and a hook for a trimmer for grass (when I worked on a trimmer, there was a fashionable shoulder belt and a plastic belt. It was more convenient, but this belt did not bother me)

Read the instructions before using! And you will be happy. “Experienced” users strive to do everything at their discretion “Concept” as a result of negative reviews appear. The trimmer for the grass was purchased for mobile use so that it can be put into the trunk, and this will not happen if Al-ko is stolen or broken (I do not like to communicate with the service). On the way, mow a plot of 15 acres. There are no problems with the trimmer (except for a clumsy belt), the main thing. after work, connect the remaining fuel mixture and leave the fuel in the carburetor. I laid 3 mm fishing line for a trimmer with the profile “Zvezda”, cutting everything, even raspberries and firewood, although you need to keep high speed. This is even easier with the disk, but you need to be careful not to contact stones or other hard objects. You can mow high grass, but you need to maintain high speed, because you can wind the stems on the shaft. For such work, it is better to immediately take a trimmer for grass with a more powerful engine. After two years of use, I add, the oil should be good and diluted in accordance with the requirements of the manufacturer of this oil, otherwise the entire trimmer for the grass in the release zone will be contaminated with unburned oil. I add it after five years of use: 1. I replaced a three.lobed disc with a four.blade with short blades and a large center, it became better to mow high grass. The folds are well braked. 2. The engine power has fallen, the sparking grill and the muffler were cleaned, the braid works normally again.

Pros: cheap, starts well from ordinary and fresh fuel, is easy to use.

Disadvantages: Disgusting belt, it had to be adapted from the old Husqvarna.

You need to either add additional hair to the set, or highly recommend buying a couple more! I again really wanted to mow that a woman without technical preparation had to cut a trimmer for the grass almost half (then it was already easy, if she pulled it too much), change the fishing line for a knife and continue the mowing. By the way, yes, to mow abandoned areas with a knife is very good. In the morning I will go to mow the overgrown field next to the potatoes. But seriously, the trimmer for the grass Patpiot GP PT 3055 is easy to operate, not very thunderbird. You just need to disassemble the coil. Change the fishing line for the trimmer, something did not work. Well, morning wiser in the evening.

Advantages: a woman without technical training gathered, refuel and went to mow!

How to unscrew the disk from corner grinders.

Without this, neither there nor here! And if this suddenly does not work, you will have to dodge in every way, search. Installation of the ignition coil on a single tractor. Coil For bassores. Repairs of chainsaws of principal trifles repair of chainsaws. HT31 head- Part two NEMO NEMON. Coil The trimmer for the grass does not unscrew. The desired life hack. Huter electric crossbar reassignment. This is not a learning. I have no one else I teach how to collect, repair and the rest. The situation has developed. How to make a trimmer for grass Andrei unwitted. How to change piston on a trimmer.

In this I will show how without the help of others, rapidly change the piston on the trimmer. I will change on a trimmer. Upper and lower gearbox Trimmer for grass. About gearboxes on trimmers, the lower gearbox and the upper gearbox of the bell of the one to realize how they are excellent. Service, service, tuning. Business, money macroeconomics. Production enterprises. Own business. Real estate, mortgage. Accounting, audit, taxes. Other business areas. Debts, collectors. Dating, love, deeds love. The rest of the relationship. Software.

Mobile devices. Education kindergartens. Additional education. Other education. Philosophy, unknown magic, esotericism. Other unknown. Travel, tourism independent rest. Other tourist. Pregnancy, childbirth. Education of babies. Furniture, interior. Suburban life. Wedding, wedding, marriage. Twist or unscrew the nut without fixing the shaft will not work. To change the cord, it will be enough to release screws, stick a segment of the fishing line of the desired length and crush it. Also, a mowing nozzle for fixing the fishing line on it can be made from the iron sheet.

How to do this can be realized from the subsequent. Service centres. Technique announcements calculators brands Readings Reviews. Technique for the Garden Trimmer for the grass Repair of a trimmer coil for the grass with your own hands. One trimmer coil device for grass two main malfunctions of the coil 2. Also curious: prerequisites for damage to gasoline and electronic trimmers. Why are there a moment. Repair and lubrication of a trimmer gearbox for grass. Created an apparatus indicating a laser to the presence of a mosquito in an apartment.

Method 1

The 1st method that inspects the ignition coil implies the introduction of special equipment (shield). In home criteria, he is unavailable to find it exclusively in service centers.

Magneto disassembly is carried out painfully. At first it is necessary take off from the motor this device and clean it, eliminating particles of oil and mud. Further, because the ignition automaton is firmly fixed, it is necessary to unscrew the nut, and then take off part and remove the key from the groove. The cover is fixed on four screws to remove it, you need to turn it out and remove the fasteners. Then it is necessary to remove the magneto rotor from the case, unscrew the studs holding the transformer, and get it. And in order to collect magneto, it is necessary to fulfill the deeds described above in a working order.

Repair of Patriot gasoline trimmers

The 1st specialized service center “Agrotekervis” is ready to offer you professional repair of benzos and trimmers Patriot. Our company has experienced, certified and qualified mechanics that qualitatively perform any types of work in the field of maintenance and repair of garden equipment.

PT 2340, PT 2540 ECO, GG 262, GG 362, GG 562, GG 462, PT2540 Imperial, GG 224, PT 3045, PT 4555ES, PT 5555ES Country, PT3045 Imperial, PT 2540, PT3055 Imperial, PT 545, PT 555, PT3355 IMPERIAL, PT4355 IMPERIAL, T 530 PRO, PT 3055, PT 536J, PT 3355, PT 546J, PT 415

The list does not indicate all models of the repaired trimmers.

Attention! Before contacting the service center!

We ask you to inform the manager of our company in advance: the exact model of equipment. If you need spare parts for Patriot lawn mowers, you need to know: the brand of your engine; engine model; type of; The code located at the installation site of the carburetor, the spark plugs or muffler. The engine code is indicated by a line consisting of 3 groups (in each line 6-signs without additional quotes and stars).

The cost of repairing benzos and trimmers Patriot

We are responsible for the results of our work, confirming that our words do not disperse with the deed!

Repair and service of garden equipment.

Specialized Service Center “AgrotechService”. Warranty and post.warranty service of the equipment of world manufacturers! Attention! Information for users!

Do.it.yourself Patriot

Details: repairing Patriot mowel with your own hands from a real master for Olenord.com.

Active operation of garden equipment leads to a quick failure of individual nodes or parts. It is not necessary to dispose of the technique, since it can still be useful in the future. After all, after sometimes carrying out a small repair of the lawn mower with your own hands, you can return it to the previous working state.

Depending on the area of ​​the lawn and the growth of grass on it, the owners choose the optimal technique in characteristics. It is several types:

The average mower stands in the climatic conditions of St. Petersburg, or similar regions about four seasons. expensive or less operated garden assistants are able to withstand in the field of 5-6 seasons.

Also, the restoration of lawn mowers with your own hands will be required if the conditions of winter storage are inappropriate. For example, after use, there were no cleaning surfaces or there was no off.season preventive maintenance. As a result, various problems are manifested:

• frequent sharpening of the lamp of the lawn mower is required;
• just does not start a lawn mower;
• The motor starts up, but through a short gap the lawn mower stalls;
• malfunctions of the carburetor appear, which requires not only disassembly, but also cleaning with repair;
• Do.it.yourself renovation of the lawn mower is required with a significant reduction in power during operation.

You should not go to an expensive service center. Many problems can be solved with minimal costs and repairs on your own.

After each use of the tool, it is necessary to clean the cutting elements. Change the oil regularly and perform a minimum risk.

Mowers, inside of which electric motors are located, most often begin to be capricious due to oxidation of contacts. The terminals are covered with a layer of scale from excess humidity in the room or in another place of storage. It is also worth checking the absence of a break in wires in problem areas. For this operation, a multimeter or other tester type is used.

When a set of garden equipment contains a brush engine, we identify the performance. Brushes can wear out quickly, leading to a lack of contact. The reptity of them costs relatively little, and it is easy to find it in specialized stores, where they sell spare parts for such a technique.

Asynchronous engines are also in wait for the malfunctions. They refuse phase.drive capacitors. A similar situation is diagnosed at home is problematic. It can be detected by indirect symptoms:

• The sound of a buzz is heard;
• When starting, the case twitches slightly;
• significant heating of the motor occurs even at a slight load;
• Reduces are reduced.

It is worth diagnosing the condition on the tolerance/button and the voltage supply to the electric motor. Когда проведено тестирование описанных узлов, а нарушений в работоспособности не обнаружено, то вряд ли удастся исправить поломку газонокосилки своими руками. Then you will have to use the services of the corporate service.

Primary diagnosis is carried out from the stage of elimination of the most obvious breakdowns. When the motor does not start, it is worth monitoring the presence of fuel in the tank. If there are its remnants from last season, then it is worth replacing it. Low.quality gasoline after wintering is able to lose its characteristics, give an undesirable sediment or even stratifying at a fraction in density. In this form, he is not able to start the engine, but only clogs the system.

At the second stage, we find out why the spark does not appear. Its loss will not make it possible to ignite the fuel. Remove the cap from the candle and unscrew it from the planting nest by a special clip that came with a mower. Next, we throw the cap to the candle, bring it closer to the threaded part or the metal element of the motor, and at this time the partner pulls the starter.

With such manipulations, a blue powerful spark is required to appear in the working node. She will be able to notice her even in daylight. It is important to test this next to the unpainted metal part of the engine that can conduct current.

When there is no spark, you need to go for a new candle to the store. Do not return to the motor even with a weak or unstable spark. It is better to clean the working contacts from the haze on the head.

During operation, the occurrence of rattling in the design is possible. It at first does not affect the performance of the mechanism as a whole. However, it can lead to unbalancing and increased noise during operation. It is worth tightening the fasteners on the frame in a timely manner.

Tightening fasteners on the frame

An uneven slice of grass is evidence that you need to sharpen a lawn mowing knife. It’s not so difficult to get to them, but it is important to completely turn off the equipment from power. You can work on your own using tisses and files or on a solid sandpaper. It is important to ensure the cut angle uniform throughout the line 30 degrees. If there are excellent sections in the surface, then this is evidence of getting on a solid surface. Replacing them will cost quite expensive.

After turning on, a whistling sound appears. An unpleasant acoustic effect is associated with the penetration of foreign elements inside the design. They can block the video in the aerator. You can solve the problem with disconnecting a blocked roller and subsequent extraction of an extraneous subject.

The engine of gasoline equipment becomes almost immediately after the start of short operation. The culprits are a jammed crankshaft or a piston. In parallel, we check the presence of oil in the crankcase. On the disconnected engine, manually start the rotation or add the oil as necessary. However, in such a situation, you often have to apply for recovery to specialists.

Before starting repairing the engine of the lawn mower, it is worth checking if the pistons lay down. To do this, it is necessary to dismantle the motor. We also remove the carburetor from the structure and conduct visual control for the availability of possible defects. Usually in disassembly you will need a special Torex screwdriver with nozzles.

TRAMMER Repair for Patriot grass with your own hands

Details: Repair of a trimmer for Patriot grass with your own hands from a real master for Olenord.com.

In this video I repair my trimmer for Patriot grass. I will also tell you what breakdowns happened to him, well, my impressions after three years of work. Also try to dig young potatoes, see how much it has grown.

My channel Libral1973: https: // www.YouTube.COM/user/Libral1973 How to make a puller with your own hands: https: // www.YouTube.COM/Watch?V = G7SB-C74U7G mesh rabits with your own hands: https: // www.YouTube.COM/Watch?v = ordgiwewcxe Feature DIY LED: https: // www.YouTube.COM/Watch?v = akoljb_7lx8 portable column with your own hands: https: // www.YouTube.COM/Watch?v = FHHMW1YPCG Minitor with your own hands: https: // www.YouTube.COM/Watch?v = g0io9mx9ly8 DIY muffler: https: // www.YouTube.COM/Watch?v = gkzapmlwrto How to configure valves: https: // www.YouTube.COM/Watch?v = 5hpsxdqjrbs

The Patriot PT 3055 gasoline trimmer is a comfortable and productive tool for processing sections with grass that require careful and clear cutting and trimming in height. The unit is used for brisk mowing and trimming of herbs on personal laws, along floral flower beds, fences, walls, courts and lawns.

• Thanks to the high.quality design of the two.stroke engine and its upper location in the structure, a small noise level of up to 70 dB is released.
• Fuel tank made of transparent, stable material to brutal environments.
• Automatic fishing line.
• The width of the strip capture with a knife up to 220 mm.
• Cutting of excessive fishing length is made by a special knife in a protective casing.
• Air filter is multi.stage, captures large, medium and small fractions of suspended dust and hard particles.
• The rod is detachable, comfortable for transportation and storage.

• In the production of the device, modern materials and assembly technologies were used.
• A new anti.vibration system is provided.
• High performance is achieved due to the brilliant motor with wear.resistant and correctly attached details.

• Ordinary and mobile control system. On the bicycle shape in the reach of the start.up zone is the start button and the gas clamp, which allows you to carry out work with clear calculation and mobile control.
• For lubrication of drives, a line of unique motor oils was developed.
• The simplicity of the assembly and use of the tool is designed for an ordinary person without special technical knowledge and work experience.
• Nonal exploitation. The protective casing protects the operator’s hands from injuries.
• The handle of the main bar is installed and fixed and fixed so that the open part is placed on the right side of the handle.
• The handle is made to the bolts not to the end, but taking into account the next adjustment.
• The control handle is installed by a gas trim.
• The fastening screw is twisted with a small effort. Cable clips on the handle are attached.
• The shoulder belt is snapped by a carbine for a special fastening on the main rod of the unit.
• To the lower part of the bar, at the base, a metal casing is screwed onto the protective case of the gearbox, and a plastic casing is attached to the top to enhance protection.
• A protective flange is installed on the slotted gearbox with the coincidence of technical grooves on the gearbox with flange.
• A fixing rod or hexagon is inserted between the gearbox and the flange.
• The trimmer head is twisted to the stop, against the course of the time of time.
• A cutting knife is installed on a protective flange.
• A knife is pressed with a puck and twisted by a nut to the stops against the course of the clock.

If the knife is stuck on one side, then it is turned over and use the second sharpened side.

• Both parts of the rod are connected using a fixing lever of the fastener system.
• Checking the correct assembly: the impossibility of opening without pressing on fixing fasteners.
• The additional mounting of the coupling of the connection is tightened to the stop. This gives an advantage when using the unit to perform different works: the lower rod is installed on fixed angles of 90 and 180 degrees.

• A trimmer is dressed for grass.
• The shoulder belt is adjusted to the individual characteristics of the operator figure.
• The bolts of fastening the handle are twisted to the stop.

• The preparation of fuel mixtures for a trimmer for grass is made only from original Patriot motor oils for two.stroke engines.
• Gasoline for filling in the motor is used from a high.octane row, not lower than AI 92.
• In the configuration to the trimmer there is a special canister for the fuel mixture with marks for breeding.

• Gasoline is poured into the container to the corresponding mark.
• Oils for gasoline, and not vice versa, flows oil for a two.stroke engine to the level
• The mixture shakes it several times until uniform.
• If a special container is not provided in the configuration, use the usual gasoline canister. Make a mixture in this ratio of gasoline/oil 32: 1.
• To prepare a mixture directly in the fuel tank of a trimmer for grass is not recommended.

Hi all.This is not a learning.I have no one else I teach how to collect, repair and the rest.The situation has developed.

Approximate management how to disassemble a trimmer for grass, for example, get to the starter or ignition coil.

An indispensable tool for a modern summer resident or the owner of a private house is a lawn mower, which allows you to effectively and efficiently bring the adjacent territory in order. The period of active use of motorcycle is in late spring until October of the month. Modern units are equipped with powerful and hardy ICEs, enhanced transmission and main nodes. Despite this, physical wear, production marriage or improper exploitation leads to the failure of a trimmer for grass. In order to repair a trimmer for grass with your own hands, you must have at least basic knowledge in the field of technology and a little experience in its repair.

Trimmer for Patriot 3045 Hand Repair

Details: trimmer for Patriot 3045 grass, repairing yourself from a real master for Olenord.com.

Hi all.This is not a learning.I have no one else I teach how to collect, repair and the rest.The situation has developed.

Approximate management how to disassemble a trimmer for grass, for example, get to the starter or ignition coil.

In this video I repair my trimmer for Patriot grass. I will also tell you what breakdowns happened to him, well, my impressions after three years of work. Also try to dig young potatoes, see how much it has grown.

My channel Libral1973: https: // www.YouTube.COM/user/Libral1973 How to make a puller with your own hands: https: // www.YouTube.COM/Watch?V = G7SB-C74U7G mesh rabits with your own hands: https: // www.YouTube.COM/Watch?v = ordgiwewcxe Feature DIY LED: https: // www.YouTube.COM/Watch?v = akoljb_7lx8 portable column with your own hands: https: // www.YouTube.COM/Watch?v = FHHMW1YPCG Minitor with your own hands: https: // www.YouTube.COM/Watch?v = g0io9mx9ly8 DIY muffler: https: // www.YouTube.COM/Watch?v = gkzapmlwrto How to configure valves: https: // www.YouTube.COM/Watch?v = 5hpsxdqjrbs

The Patriot PT 3055 gasoline trimmer is a comfortable and productive tool for processing sections with grass that require careful and clear cutting and trimming in height. The unit is used for brisk mowing and trimming of herbs on personal laws, along floral flower beds, fences, walls, courts and lawns.

• Thanks to the high.quality design of the two.stroke engine and its upper location in the structure, a small noise level of up to 70 dB is released.
• Fuel tank made of transparent, stable material to brutal environments.
• Automatic fishing line.
• The width of the strip capture with a knife up to 220 mm.
• Cutting of excessive fishing length is made by a special knife in a protective casing.
• Air filter is multi.stage, captures large, medium and small fractions of suspended dust and hard particles.
• The rod is detachable, comfortable for transportation and storage.

• In the production of the device, modern materials and assembly technologies were used.
• A new anti.vibration system is provided.
• High performance is achieved due to the brilliant motor with wear.resistant and correctly attached details.

• Ordinary and mobile control system. On the bicycle shape in the reach of the start.up zone is the start button and the gas clamp, which allows you to carry out work with clear calculation and mobile control.
• For lubrication of drives, a line of unique motor oils was developed.
• The simplicity of the assembly and use of the tool is designed for an ordinary person without special technical knowledge and work experience.
• Nonal exploitation. The protective casing protects the operator’s hands from injuries.
• The handle of the main bar is installed and fixed and fixed so that the open part is placed on the right side of the handle.
• The handle is made to the bolts not to the end, but taking into account the next adjustment.
• The control handle is installed by a gas trim.

• The fastening screw is twisted with a small effort. Cable clips on the handle are attached.
• The shoulder belt is snapped by a carbine for a special fastening on the main rod of the unit.
• To the lower part of the bar, at the base, a metal casing is screwed onto the protective case of the gearbox, and a plastic casing is attached to the top to enhance protection.
• A protective flange is installed on the slotted gearbox with the coincidence of technical grooves on the gearbox with flange.
• A fixing rod or hexagon is inserted between the gearbox and the flange.
• The trimmer head is twisted to the stop, against the course of the time of time.
• A cutting knife is installed on a protective flange.
• A knife is pressed with a puck and twisted by a nut to the stops against the course of the clock.

If the knife is stuck on one side, then it is turned over and use the second sharpened side.

• Both parts of the rod are connected using a fixing lever of the fastener system.
• Checking the correct assembly: the impossibility of opening without pressing on fixing fasteners.
• The additional mounting of the coupling of the connection is tightened to the stop. This gives an advantage when using the unit to perform different works: the lower rod is installed on fixed angles of 90 and 180 degrees.

• A trimmer is dressed for grass.
• The shoulder belt is adjusted to the individual characteristics of the operator figure.
• The bolts of fastening the handle are twisted to the stop.

• The preparation of fuel mixtures for a trimmer for grass is made only from original Patriot motor oils for two.stroke engines.
• Gasoline for filling in the motor is used from a high.octane row, not lower than AI 92.
• In the configuration to the trimmer there is a special canister for the fuel mixture with marks for breeding.

• Gasoline is poured into the container to the corresponding mark.
• Oils for gasoline, and not vice versa, flows oil for a two.stroke engine to the level
• The mixture shakes it several times until uniform.
• If a special container is not provided in the configuration, use the usual gasoline canister. Make a mixture in this ratio of gasoline/oil 32: 1.
• To prepare a mixture directly in the fuel tank of a trimmer for grass is not recommended.

Repair of the starter of a gasoline trimmer for grass may be required at the most inopportune moment. In this case, you can solve the problem in two ways: replace the broken part or change the entire node. The latter option will cost more. To repair the device with your own hands in most cases, you need only a screwdriver with an appropriate tip from the tools. Repair work will not take much time and do not require special knowledge. It is enough to know the device, the principle of operation, the nuances of the assembly-disassembly of the starter on the trimmer in order to achieve the desired positive result.