Adapter for power tiller with steering wheel with your own hands

Device

Each element of the adapter for the power tiller is an important part of it. The leading element of the adapter is the clutch mechanism. It is on him that the reliability and stability of the connection of the power harvester and adapter depends. When the trailer is not equipped with steering, the coupler is mounted on a horizontal hinge. Sometimes it is possible to twist and turn.

The reinforced coupling mechanism resembles a welded assembly inserted into the frame and securely bolted down. These are two pieces of square tubing welded together plus a 1 or 1.5 inch round piece of ordinary tubing. Inside the tube there is a rod to which a tee is welded. It is the stem that is responsible for turning the tee on the controlled axis and smooth running on uneven ground.

As for the wheel fixation node, it looks like two pieces of pipe welded at an angle of 90 degrees with respect to each other. The horizontal piece is inserted into the mounting tube and secured with a bolt. The axle with the wheel located is secured to the bearings.

Suspensions used in adaptor assemblies can be pivoting, axial or axle-type. They have no resilient parts. The operator’s workplace allows the user to be positioned in a safe and secure manner. Dual control system is also possible in some variants.

The frame of the device can be either a ridge frame or a ladder frame. It is also possible to pick up a variant, in which the frames of the machine and trailer are combined into one unit. In this case, you have to build a pedestal for the transmission and engine. That’s where the clutch mechanism, foot rest, post with seat, brake, and wheel mounting tube are welded to the frame. Side tubes of the frame are the same length, each 40 cm. The adapter can also have a three-point hitch, which increases the performance of the main unit.

Adapters for power tillers with steering

The single-axle tractor is a mechanized helper for the gardener, which reduces labor costs and the user’s health. If such a device is supplemented with a steering adapter, it increases the comfort of steering and further reduces the physical strain.

In fact, the adapter allows you to turn a single-axle tractor into a semblance of a mini-tractor. From the material of this article you will learn the device of the adapter, its purpose, varieties, nuances of installation and subtleties of operation.

Adapters and trailers to MTZ power tillers. Models of devices. Homemade variants, video reviews and reviews

Constructed front adapter on a single-axle tractor with their own hands will facilitate work on the processing of the homestead plot and vegetable garden. Additional device transforms a power tiller into a mini-tractor. If necessary, it is possible to mount such implements on the converter as a plow, digger, planter, and hoe.

Making a front adapter for a single axle tractor with our own hands

How to make a steering adapter for a power tiller? The type of construction, which provides for a steering wheel, must have a rigid fixation. The steering gear is made as a separate independent unit. A pair of wheels and an axle, which serves as the steering drive, are installed in the front and rear. The attachment points are selected according to the individuality of the machine. The location of the steering gear depends on the type of spare parts. When assembling, it is recommended to perform just such an improved model.

Motor cultivator with steering control has many positive qualities:

• The operator will not waste energy in moving behind the machine;
• the technique has maneuverability and increased functionality;
• The tractive force is realized by 100%;
• on a power tiller you can drive to the workplace, without the use of additional equipment;
• ease of operation compared to other options.

Tools and materials needed

By your own hand and even without help, you can make a hand-operated adapter or a dumping adapter. Therefore, first of all, it is necessary to determine the type of additional equipment. The next step is the drawings. You can use ready-made, based on the instructions for power tillers of the same brand, but already implemented with adapters, or you can create it yourself. Making drawings with their own hands, careful attention should be paid to the main elements:

When the circuit is ready, you must take care to have the following tools on hand:

• welding machine;
• drill;
• grinder;
• two wheels and axle;
• lathe;
• a finished chair of a suitable size;
• metal profile for the frame;
• Steel angle and beams;
• fasteners;
• bolts, self-tapping screws;
• electric screwdriver;
• control levers;
• a circle of steel with special holes. the basis for coupling;
• bearings;
• lubricants and primers for the finished construction.

All necessary materials and tools can be purchased at your local hardware store. If there is no chair of suitable size, it is necessary to buy a frame, upholstery and a base for the seat, and later make it with your own hands. All that is needed is to lay the padding or filling tightly on the frame, and fix the upholstery on top with a stapler. Or you can buy a ready-made plastic seat in a hardware store. Once the preparatory work is done, you can proceed directly to the manufacture of the adapter.

How to make an adapter for a single-axle tractor with your own hands

Today it is difficult to find a person who would not use a single-axle tractor for processing his plot. Further improvement of technology led to the invention of a special device with which a single-axle tractor can easily turn into a comfortable minitractor. It became possible to carry out field work in a sitting position, which greatly simplified the work of the farmer. Such a mechanism is called an adapter for power tiller.

Types of adapters for power tillers

Such attachments help to turn a single-axle tractor into a kind of mini-tractor. It connects the tool and all its accessories: toolbox for planting, ridging, flatbed, plow, etc.д. If you install an adapter to the power tiller, then all the gardening and gardening work is greatly simplified, since it is automated. It also helps increase operating speeds of up to 10 km/h.

The adapter design looks like the back of a cart with a seat.

Some models may have a special lever for lifting. It provides a more comfortable operation of the machine. If necessary, the single-axle tractor can also be used for transporting small loads. Depending on the purpose for which the technique will be used, the drawbars can be lengthened or shortened. In the first case, they are used for more oversized machines, and in the second case. for lighter structures.

In more advanced models, the drawbars can also be telescopic, and they also have the ability to adjust the track width.

To connect the adapter to the tiller, a single enlarged coupling is used that consists of two parts: the first is a connecting link and the second acts as a regulator. If there is a need to equip the machine with several implements at the same time, a double universal coupling is used.

You can perform a more complex design or simplified. Both options are shown below.

For the simplest version of the adapter you will need:

Tractor with Trailer. Changfu Brand 18CY Model

• Rectangular cross-section pipe;
• welding machine;
• wheels;
• bearings;
• channel 0, length 40 cm;
• fixing bolts;
• hitch;
• the seat.

The assembly step is as follows:

• First of all, the pipe is cut into 1.7 and 0.5 meter sections. A shorter one is welded strictly perpendicular to the end of the longer pipe. It will be the base for mounting the wheel supports. You should immediately make a mark of 30 cm, which will indicate the height of props from the axis.
• Next, the wheels are mounted on the hubs, which are made if necessary, using a lathe. In order not to buy new wheels, you can use the old wheels from the garden cart. At first mount bearings on the bushings, and then weld the struts on the center tube and bushings. The length should be oriented to the angle of inclination in relation to the construction itself.
• The frame is made to the size 40×40 cm, but if necessary this size can be increased or decreased. To organize the attachment equipment to the rear end of the frame, a channel is fixed by welding. The side tubes of the structure are connected to each other by bolts. On the frame should also be installed a lever. It can have three “elbow” lengths: 0,2, 0,3 and 0,5 m. To increase the adjusting force, you should install an additional lever (length 75 cm).
• Often, hitch assemblies are purchased in stores. But here it is worth noting right away that this element must be of high quality. So if you plan to make it yourself, special attention is paid to this quality.
• The seat is attached to the metal support, which must be pre-welded to the base of the frame, that is, the central tube.

Any work on the land takes a lot of effort and time. Therefore, gardeners are increasingly using special equipment, such as power tillers. But you can’t do everything with this machine. Without a special adapter you will not be able to weed or dip the ground, as well as remove snow and construction debris. A cart with a seat for your power tiller is now quite expensive. But there is a way out. In our article you will learn how you can make a homemade adapter for a motorblock with your own hands without much effort.

Making an adapter to the power tiller with your own hands

If the design of a power tiller can be called simple, the same cannot be said about the process of making it. When developing a homemade adapter to the motor block, you need to pay attention to the scheme of drawings and dimensions of the adapter, which play a key role in the further development of.

First of all, you need to carry the following tools and parts:

• welding;
• drill;
• file;
• saw;
• electric screwdriver;
• metal plates;
• 2 wheels;
• metal corners
• anchoring.

When developing a drawing of the future adapter for a motor-block with their own hands, it is necessary to take into account what constituent elements are included in the design:

• the layout design. at the very beginning it is necessary to calculate everything so that all systems and mechanisms are in equilibrium, and to prevent cases of overloading of the system. You can use already drawn schemes, but you can make it yourself;
• creation of basic details. during the practical implementation of the drawing, you need to pay special attention to the rotation of the body. It should occur easily, without hindrance. The frame is based on metal pipes and angles. The body of the adapter is made of metal plate;
• installation of the driver’s seat. It is placed on the beam at a distance of 80 centimeters from its front part. The design can be supplemented with seat adjustment, additional levers.

The design can also be supplemented with additional agricultural tools:

Adapter for power units

Most often there are two couplings in the adapter. one of them attaches the attached additional equipment, and the second allows to attach it to the power harvester. For example, it is possible to attach such additional elements to the adapter:

Wheelset and axle in the adapter are quite robust structures that allow you to operate a single-axle tractor even on the most difficult terrain, as well as for the transportation of fairly heavy loads. It is important to understand that the transportation of goods on public roads on such a unit is prohibited, for this reason they and are used only in rural areas. However, despite a certain structural similarity between all adapters, they are endowed with some significant differences.

For example, there are rear adapters on the steering, four-wheel drive adapters and front units.