How to cut a countertop for an oval sink

How to cut a countertop for a sink

Preparing a countertop for installing a sink is not a very difficult task, but rather painstaking, it requires diligence, free time and personal labor. A properly cut hole is a guarantee of the elementary installation of the sink, and as a result, getting pleasure from washing dishes.

To make the hole neat and correct, you need to follow these rules:

We outline the sink with a pencil along the contour

Penciled spot where the sink will bump

Cut out a hole for a sink through masking tape

Silicone edge finishing

Helpful information! The distance from the wall to the sink should exceed 10 cm, which will make it possible later, during its installation, not to allow vulnerable places to break or be damaged!

You can see more details on how to cut a hole for a sink in these

How to cut a countertop for different types of inset sinks

The sink space in the countertop can be cut in several ways. But the main principle that unites them is the mandatory observance of the geometry of the recess in the countertop during work. At the very beginning, it is worth understanding for yourself which method you are going to use. The main point that should not be forgotten is the presence of individual features of the sink. We will deal with the installation rules and its types.

On the left. installation of the sink flush with the worktop, in the center. on top of the worktop, on the right. below the worktop

Installing a sink under the countertop

With this installation, the countertop will rise above the edges of the sink. This type is used for furniture made of expensive materials, which has sophistication, attractiveness, rigor.

Sinks installed below worktop level

For this, special sinks are purchased for under-table installation. The sink is fixed with brackets or screws (for expensive materials. special self-tapping screws).

The holes for the sink in this version are cut out with special professional equipment (you can use a jigsaw with diamond-coated blades). The edges of the hole are very carefully sanded and covered with a moisture-resistant film or special means.

It is quite difficult to install this type of sink on your own. It is recommended to contact the professionals.

With this type of installation, the following points should be taken into account:

you need to get an under-table sink of your chosen shape and tools for its installation;
after the end of trimming, the edges must be treated with special means, which subsequently will not allow moisture to be absorbed and will repel it.

In the simplest version of the installation of the undercounter sink, the countertop is cut out in the standard way, but from the inside of the countertop. The main thing is to measure everything in such a way that the sides of the sink are exactly along the cut hole. they do not protrude or fall behind it. The meaning of installation is that the sink will be screwed on from the inside of the countertop, and then it simply turns over and is installed on the kitchen set.

You can, of course, not turn the tabletop over, but work initially from the bottom, but in this case, the whole process will be less comfortable.

For more details about this method of installing the sink under the countertop, see the short

Installing a sink on top of a worktop

This procedure is the simplest, and even a non-professional can handle it.

The hole in the countertop is cut out in the manner described in the relevant section above. over, light flaws in a couple of millimeters will not be very critical.

Silicone sealant is applied along the edge of the hole or on the sides of the sink. The sink is installed from above in the opening and is well pressed against the countertop. Excess sealant is removed with a rubber spatula.

Flush sink on top of the worktop

If there are additional clamps (e.g. legs) for the sink, they can also be screwed under the worktop.

Installation of a flush sink

For master classes on this simple method of installing a sink, see the following

Sizes and shapes of sinks

These indicators are related to the main characteristics. It is worth deciding with them from the very beginning, so that later everyone would be convenient and comfortable in the kitchen space. The most common and demanded are considered to be:

You can opt for other shapes: oval, with rounded corners, triangular, pentagonal, hexagonal, trapezoidal, intricate. It all depends on your needs and preferences. The number of bowls can also vary. There can be two, three or one copy of them. They can be the same or different sizes.

Various forms of sinks for the kitchen

Kitchen countertop materials

To make the right choice, you need to have information on what kitchen countertops are produced. There are plenty of options: for every taste and wallet. There are simply functional, and there are those that become a decoration of the kitchen. The main selection criteria are:

aesthetic and appearance;
waterproof and moisture resistant;
resistance to mechanical damage;
hygiene compliance;
environmental friendliness;
coating durability;
resistance to external factors.

The main and most common materials for the manufacture of countertops are:

Material name

Minuses

Plastic

Flush-mount sink installation

In this case, as in the first, it is important to cut a hole in the countertop as accurately as possible. In this case, the main difficulty lies in the fact that, in addition to the main hole, cut small sides along its perimeter to match the dimensions of the sink sides.

The sink is inserted on top of the worktop and joins its sides with the recesses in the worktop, thereby becoming flush with it.

Flush-mounted sink

You can learn more about installing a washbasin flush with the countertop from the excellent

Before you start to act, you must first properly prepare the surface. This means the following:

a special tool and tool is taken and the areas of contact with the washing surface are worked out, thus there are depressions corresponding to the thickness of the sides of the sink being installed;
you need to deepen ideally along the entire perimeter of the built-in sink;
it is worth noting that there are certain difficulties in such work, so all actions must be neat, well-coordinated, unhurried.

Equipment and tools for installing a sink

To cut a hole in the countertop for a sink, special skills and experience are not required. But the tools and equipment must be available.

First of all, you need to acquire:

ruler;
pencil;
corner;
level;
tape measure;
screwdrivers;
rasp;
screwdriver;
adjustable wrenches;
a set of wrenches;
brush;
a drill for woodworking with a diameter of 10mm;
electric jigsaw;
with an electric drill;
PVA glue;
appropriate sealant.

The tools must be of high quality so as not to spoil the whole process.

Installing a sink in a countertop. why we choose a flush sink?

There are two ways to organize a sink in the kitchen. overhead and mortise. In the first case, you, along with a bowl for washing dishes, receive a pedestal or cabinet on which it is placed. But in the second case, the installation of the sink is carried out into the countertop of your kitchen set. Most often, buyers’ preferences are given to the flush-mounted version, although it is more troublesome to install, it still has a number of advantages that force us to make a choice in its favor.

The first, and most important, argument not in favor of an overhead sink is considered to be the constantly reigning humidity in the kitchen, which forms between the cabinets adjacent to the unit with the sink. Further, users argue for the variety of assortments and the aesthetics of the sinks. Here you can often find a wide selection of both materials and shapes. Ceramics, porcelain stoneware, stone, plastic, stainless steel, copper, bronze. an enviable list, right? And if you diversify it with round, rectangular, angular and various asymmetric shapes, then the eyes run up.

When thinking about how to embed the sink into the countertop, it should be borne in mind that it can be installed in three ways: exactly at the level of the countertop, slightly lower and slightly higher. It depends not only on your desire, but also on the configuration of the purchased kit. Specify how the bowl should be located, what fasteners are used during installation. Also, think about how durable they are, and what may affect their service life, because sometimes the quality of the sink is good, but it is attached almost on parole.

How to embed a sink into a worktop. let’s do a great job

Required tools

In this article, we figure out how to embed a sink into the countertop, and if you joined us, it means that you have a change of scenery in your kitchen, and I would like to try myself as a master. Well, we will try to consider in detail all the pitfalls in order not only to carry out the installation, but also to ensure the durability of the new acquisition.

How to embed a sink into a worktop and prepare for surgery?

Before figuring out how to install the inset sink in the countertop, you should make sure that you have a reliable water supply to the inset site and that the sewage system is also well established. Of the strategically important tools that you will need to look for through friends, perhaps more than one day, if you personally do not have them, you can bring a jigsaw. It is pointless to start work without it. From purchased materials, in addition to washing, there must be a sealant, preferably transparent silicone.

Buying a sink, you can get a pleasant surprise. a template for its inset (it acts as its packaging), otherwise you will have to draw it on the countertop, applying the sink. Also, do not forget that if the kitchen set is completely new, then there are no holes for pipes, in fact, like the pipes themselves, it is possible. That is, the siphon and associated hoses are purchased independently, they are rarely included in the sink kit.

If you are just assembling furniture, and you have the opportunity not to fix the countertop lid for now, then do not do it. This will make it more convenient to cut.

How is the sink installed in the countertop?

Often the installation of the sink is carried out by the manufacturer. But it happens that this service is not spelled out in the price list. Then this concern rests on your shoulders. But don’t worry. The installation of the sink can be done by hand, armed with the necessary tools and professional advice.

The sink insertion includes several stages. Initially, you should make a hole in the middle of the pattern, then finish off the edges. The next step is to insert the sink, fasten its back side and seal the distance between the countertop curtain and the sink. The final stage is the supply of water supply and sewerage communications.

The key to a high-quality sink installation is: the reliability of the fasteners, sufficient fit and high-quality sealing. Moisture is a rather aggressive factor affecting the kitchen countertop, especially if it is made of chipboard. High-quality installation will not allow the countertop to dry out or swell, which will extend the service life many times over.

Tips from professionals

The hardest part is making the right hole. If it turns out to be more than it should be, then the legs will not be able to hold the sink. Saw out the hole, almost reaching the markings, and if the sink does not enter, it will help to adjust the hole to the size. a rasp.

Different silicone cures differently. Before pressing down on the edges of the sink, check how long a drop lasts in minutes. Silicone may burst if you hurry.

Do not tighten the screws too tightly. Otherwise, the sides of the sink will bend up.

Hello dear friends! Today we’ll talk with you about how to embed a sink into the countertop, what is required to work at home and how to implement the idea with your own hands.

We embed sinks in the kitchen, and in the bathroom it may be necessary to embed the sink. At the same time, there is no fundamental difference in where exactly these actions take place.

But there is a difference in whether you embed a round, oval or rectangular sink, and the material for making the countertop and the embedded element itself matters. In particular, in kitchens and bathrooms, stone and metal countertops, ceramic and made of MDF can be used, there are products made of artificial stone. I don’t think it’s worth reminding you that a moisture-resistant countertop is needed in the kitchen and bathroom. Especially under the sink. I will try to touch on all these points to one degree or another today.

Sink options

Using video and photo instructions, you can independently and absolutely correctly complete the insert or installation without any problems.

But the step-by-step instructions can be focused on specific products that need to be fixed on the countertop. The chosen installation method directly depends on which sink you purchased.

Required tools

Lifting mechanism for the bed: do-it-yourself calculation and installation

Invoice. The cheapest and easiest to install. Fits on a separate moisture-resistant cabinet. The disadvantage here is that there will be a gap between the sink and the cabinet;
Mortise. Installed in the kitchen or bathroom countertop itself. Here you will need to cut an accurate and neat hole;
Under-table. This is a more expensive segment. Installation is carried out slightly below the edge of the table top. This allows you to achieve excellent sealing, and the appearance is more original.

Now I’ll tell you separately how to fix this or that sink option.

By the way, you can ask local craftsmen how much it costs to install a sink. After the price is announced, for sure many will again return to the idea of doing everything on their own.

Height-adjustable furniture support: which design to choose

But all this will be possible if you turn to specialists for help, who will take upon themselves the solution of all these issues. But this service is not the cheapest, and the installation price sometimes exceeds the cost of the sink itself. So draw your own conclusions. But you will probably have to choose a product yourself. Experts and just experienced home craftsmen advise opting for a fairly deep sink (sink) and a not very high selected mixer. Yet the mixer also plays a role in this matter.

The deep sink allows you to avoid splashing water, moreover, dirty water when washing dishes. Plus a deep product makes it possible to fold a fairly large amount of dishes.

The material used plays an important role.

Sinks made of stainless steel are rightly considered the easiest in terms of installation. An alternative is enamelled steel, but its durability is lower.

To install the sink itself, cut a hole for the faucet, attach it to the wood-like countertop. made of MDF or other materials, you will need to prepare a certain set of tools and materials.

You need to keep in service the following:

Jigsaw. Electric is desirable. And buy several replacement attachments at once, since beginners often face their breakage due to unsteady movements;
Self-tapping screws, screwdrivers or screwdrivers. Actually, fasteners and tools for tightening them;
Mountings. Most often, mounts for sinks and sinks are included. Make sure of this when buying;
Sealant. Necessarily moisture resistant to withstand further stress of water and moisture.

Sealant treatment is carried out along the entire perimeter of the seat. This will ensure effective waterproofing.

If the countertop is made of chipboard or MDF, then it is doubly important to use a sealant.

How to embed an oval sink

How to properly and easily embed a sink into a worktop? This question is faced by everyone who has started repairs in their kitchen. We will tell you in an accessible and detailed way how to do the installation correctly and quickly.

How to choose a sink under the countertop

Overhead. Installed on top of the curbstone, completely cover it. Extremely easy to install. The main disadvantage is the presence of gaps between the furniture and the sink.
Mortise. They are inserted into the hole provided in the base. Installation is a little more complicated, but the sections are reliably protected from moisture.
Integrated. Practical sink / worktop combination. The side can be at different levels: flush with the table, below it, etc.
Under-table. They can only be integrated into worktops with special properties: hardwood or stone. The edge of the bowl drops below the level of the base.

In practice, cut-in devices are most often mounted. They are durable and attractive, easy to use. The most demanded equipment made of stainless steel and artificial cast stone.

How to install a kitchen sink in a worktop: 5 easy steps

The times when the choice of plumbing equipment was minimal are long gone. Modern appliances are very diverse, so even the most experienced home craftsman sometimes does not know how to install a sink in the kitchen countertop. Consider the design features and step by step analyze the easiest way.

Stainless steel sinks are practical and beautiful

Installation rules for a kitchen sink

Before starting the installation work, it is worth deciding on the place where the structure will be built. It is usually tied to sewerage and plumbing. However, modern technology allows you to embed the device anywhere in the headset. When choosing an installation site, it is advisable to follow these recommendations:

The bowl is placed as close as possible to the working area, so it is more convenient to cook.
The design divides the work surface into two parts: dirty and clean. In the first, products are processed, in the second, they are served.
Do not place a sink near a stove or refrigerator. It’s impractical.
It is desirable that there be light where the bowl will stand. Additional lighting is provided if necessary.

For a functional kitchen, it is best to choose a deep appliance: it will be possible to wash large dishes and other bulky items in it. The mixer should be chosen low. this combination will give a minimum of splashes during operation.

Watch the video on how to embed a sink into a worktop

Making and applying a template

Ready template for washing

The process of installing a sink into a worktop consists of several stages. To do this laborious work correctly, you need to carefully cut a hole in the countertop, while it is advisable to adhere to the instructions below.

Need to indent

It is recommended to place the sink at a distance of 10 cm from the wall, which in the future during installation will protect vulnerable spots from possible damage.

Once the template is ready, it’s time to use it. To make the layout of the tabletop, a template must be attached to its surface, while it must be motionless. After this operation, a contour is drawn. The same work is carried out if a factory template is available. You can cut immediately on the outlined mowing line. If cardboard is used or an inverted sink is outlined with a pencil on the countertop, additional work remains to be done. The fact is that the drawn line will repeat the edges of the sink, and its bowl will be inserted into the future hole. Therefore, you need to draw one more contour. the inner one. When drawing it, you need to take into account the distance from the edge of the sink to the fixing elements of the plumbing fixture. The result is a new template that focuses on the size of the bowl. It is applied to the surface of the countertop and a new contour is applied along which it will be possible to cut a hole.
There is an option in which a cardboard template is attached to the surface of the table top and a hole is sawn along its edges. If you look at such work from the practical side, it is inconvenient. it is better to apply the contour with a pencil. When cutting along a drawn mowing line, there is a real chance of chipping at the inner edges of the tabletop. To avoid scrap, it is recommended to glue masking tape to the surface in the area of the outlined contour, which can be easily removed in the future. In order to start sawing, it is necessary to make a hole in the body of the tabletop with a drill from the inside of the drawn mowing line. A jigsaw file is pulled into the drilled hole, after which it is fixed in the tool. You need to cut carefully and without haste, since when pressed, the blade can go away from the intended contour.
The resulting cut is cleaned with sandpaper, blown through and thoroughly lubricated with silicone. Thanks to this composition, the harmful effect of moisture on the cut surface is minimized. If any fragments of the furniture block interfere with the installation of the sink bowl, they must be carefully trimmed. Measurements for pruning must be done accurately. it is not recommended to do such work “by eye”. You need to know that when using the manufacturer’s template, cutting out the internal elements is much easier and easier, since such nuances are also provided for in its manufacture.

How to install a flush sink in a worktop. step by step instructions

Here we will give the general principle of operation, it does not matter if a round sink is installed in the countertop or sinks of any other shape.

Installing a sink in a worktop

Markup

DIY- Under-mount sink cut out. marble, granite, stone

To proceed with the final installation of the sink, it is necessary to do some mandatory work. First you need to try on the pipes and assemble the siphon, then you need to make holes in the internal structure of the countertop for the sewer and water supply. All these works are performed with a jigsaw or a crown. After that, the mixer is installed, if a place has been prepared for it on the countertop. In addition, hoses are cut if necessary. If the mixer will be installed on the sink itself, a place for the equipment is determined on the plumbing fixture and a hole of the required diameter is drilled.
Before installing the sink, a sealing tape is put on the sanitary ware. it usually comes with the device. The tape is fixed close to the edge, while leaving a special groove free, into which the silicone will be poured. Then the fasteners are installed in their places, which, when tightened, do not reach out. they will be fixed tightly after the whole structure is finally combined. If the mixer is to be fixed to the sink, it is the turn to install it. The hole is abundantly smeared with silicone, after which the sanitary ware is installed in the hole for the sink. Before mounting, the mount must be bent. In order for the sink to sit in its place and fit well into the contour of the opening, you need to move the plumbing fixture a little. After that, you need to get under the sink and finally tighten the fasteners. While the sealant is in a liquid state, it is wiped off. after a while, the composition will set and harden. If there are gaps somewhere, they also need to be sealed with sealant.

Fastening

The sink is installed in the countertop. The plumbing fixture can be used.

How to embed a sink into a worktop and prepare for surgery?

If you are just assembling furniture, and you have the opportunity not to fix the countertop lid for now, then do not do it. This will make it more convenient to cut.

Different silicone cures differently. Before pressing down on the edges of the sink, check how long a drop lasts in minutes. Silicone may burst if you hurry.

Do not tighten the screws too tightly. Otherwise, the sides of the sink will bend up.

Sources:

http://remoskop.ru/ustanovit-vrezat-mojku-rakovinu-stoleshnicu-video.html
http://chistayrabota.ru/kak-vrezat-ovalnuju-mojku/
http://www.ivd.ru/stroitelstvo-i-remont/vodosnabzenie-i-kanalizacia/kak-ustanovit-mojku-v-stoleshnicu-na-kuhne-za-pyat-prostyh-shagov-34111
http://m-stone.ru/komnaty/kuhnya/kak-vrezat-moyku-v-stoleshnitsu-posledovatelnost/

Articles countertop, oval, sink