How to cut tint on the front windows

Preparing the windows

It is best to glue the tint on the dismantled glass. In order to remove them, it is desirable to use special tools. so there is a greater chance of preserving the interior of the interior in its original form. After dismantling, the old tinting film should be removed. It will be much easier to do if you moisten it with a soapy solution. The inside of the glass is carefully washed with chemicals.

All work with the dismantled windows is best done in a special room, where there are no drafts, dust and a normal ambient air temperature. At home, there is an ideal place for this. the bathroom. Before you glue the toning film, you need to let steam into the room, and this is easy to do with hot water, which is available in every bathroom.

For final cleaning of the surface, it is advisable to go over it with a special scraper with a metal blade. If you do not have one, you can use the safety razor tip. This will help remove all the dirt from the glass and make it perfectly smooth. This is the only way to ensure that there will not be any bloat or other visible defects under the glued film.

Preparing for tinting

Virtually everything you need to carry out the work, there are in the household of the vast majority of people:

• water sprayer;
• A sharp razor blade or office knife;
• A soft clean lint free rag;
• detergent;
• rubber trowel.

You will also need warm water. Tinting a car with your own hands is possible without a hair dryer, but it greatly speeds up the process, so if you have one, you must use it too. Didactic material, abundantly available on the Internet, helps a lot in preparation for the work. Videos and photos, demonstrating how the step-by-step tinting of a car window, will clearly show all the subtleties of the process, which is impossible to convey in words.

How to tint your own car: detailed instructions

Thanks to tinting it is possible to make the stay inside the vehicle more comfortable. Tinted glass performs not only the function of protection from sunlight entering the cabin, but also hides what is happening inside the car from prying eyes.

The process of tinting is a procedure for darkening the windows of the car with a special film that has different bandwidth. The most widespread films for tinting are of dark colors, but sometimes you can see cars with tinting done with colored films.

Often car owners tint car windows on their own, which is much cheaper than if you turn to a specialized service for this. In fact, the whole process is not that complicated, and all tools and consumables can easily be bought.

Keeping it safe

Safety is very important when cutting glass because the material is very fragile and dangerous. You can not only cut yourself, but also hurt your eye with splinters.

Never use the glass cutter to cut glass on your lap or on an unreliable object. Never grasp the edge of the glass, because the untreated edges can be very sharp. If you want to lift the blanks, you should make a girth with your hands on the sides.

You should wear protective gloves and goggles before working to avoid cuts. It is also important to wear closed shoes so that the glass will not cut your foot if you accidentally fall. Clothing should be thick and thick fabric, which will also help avoid accidental injuries.

To ensure that small fragments of glass do not fall outside the working room, clothes and shoes at the end of the work is required to change.

Wrapping the rear windows

Rear window laminating is more labour-intensive in comparison with the others. Nevertheless, even a beginner can cope with this task. Technology of pasting slightly differs from previously mentioned.

Its algorithm includes the following steps:

• Applying the solution in the middle of the glass with a sponge in the shape of letter “H”;
• laying the film on the glass, with its adhesive surface facing outward;
• trimming off the excess of the film (in this case, the allowance should be more than 1.5-2 cm.);
• application of the blank (at this stage it is important to achieve the absence of horizontal folds on the film);
• smoothing the cut in both planes;
• Remove the folds with a hair dryer;
• application of the setting mortar;
• reapplying the film;
• smoothing the film.

Remember to smooth the film evenly from the center to the edges. Avoid excessive pulling and exerting force on the film.

Car Preparation

For quality results, before gluing tinting on the car with your own hands, pay due attention to the preparation:

How to Hand Cut Window Tint on the Car

Choose the film of the required light transmission capacity taking into account the standard for tinting (different glasses have their own parameters of light transmission).

Soap solution can be made from any liquid soap, shower gel or shampoo, mixing them with slightly warm water. Spatulas and spreaders are available from dealers or hardware stores.

Cut out the tint

Before you glue tinting on the car, video instructions for cutting tinting material (at the end of the article) is better to study, because all further work depends on this stage.

Cutting can be done directly on the car glass, but for beginners it is better to prepare a special glass stand for this. Next, cut and apply the film in one of two ways.

1 way

• Cut out a rectangle.
• Moisten the glass. This is to prevent the tinting material from riding around.
• Place the film light filter on the glass outside of the car for the pattern. Later on the film will be glued from the inside, but for cutting it is more convenient to work from the outside.
• Cut the workpiece along the curves of the glass with an allowance of 5-10 mm and lower the window at least 5 cm for convenience.
• Mold.
• Transfer the pattern to the stand and cut the sharp corners a little.
• Prepare strips of film (10 cm each) and stick them on the front side to make tails which will help you remove the protective layer.

2 way

• Use ready-made templates, available at any store for specific car models.
• Cut out the workpiece, leaving a small allowance of 5-10mm.
• Apply the installation compound on the inner side of the window and apply the cutting pattern.
• Make a fit and mold.
• Glue the tails.

Separately we should say a few words about shaping the film. Do it during the pasting is not worth it, because in this case you will get arrows and irregularities. That’s why it’s better to mold the film in advance. To do this at the cutting stage, when you have applied the blank to the glass, you need to apply hot air to it. After that it is necessary to go over the film with a bump so that the material would lie tightly on the glass, taking its shape. This will make it easier for you to remove the protective film.

After that the most important work of applying the film begins.

Cut the tinting

Before gluing tinting film on the car, video. instruction on how to cut the tinting material (in the end of the article) is better to learn, because all the further work depends on this stage.

Cutting can be done directly on the machine glass but if you are a beginner you better prepare a glass table. Next, cut and apply the film in one of two ways.

1 way

• Cut out a rectangle.
• Wet the glass. This is to prevent the tinting material from “riding” around.
• Place a film light filter on the glass outside of the cut-out machine. Later on the film will be glued from the inside, but for cutting it is more convenient to work from the outside.
• Cut the blank in the curves of the window with an allowance of 5-10 mm and for convenience, lower the window by at least 5 cm.
• Form it.
• Transfer the pattern to the stand and cut the sharp corners a little.
• Prepare the strips of film (10 cm) and stick them on the front side to make “tails” for which you will remove the protective layer.

2 way

• Use ready templates which you can find for the certain model of the car in any store.
• Cut the piece, leaving a small 5-10 mm allowance.
• Apply the setting compound to the inside of the glass and apply the pattern.
• Fit and Mold.
• Glue the “tails”.

We should say a few words about molding the film. Do it during gluing is not necessary, because in this case you will get “arrows” and irregularities. Therefore, it is better to make the molding in advance. To do this at the stage of cutting, when you have applied the blank to the glass on it need to supply hot air. After that it is needed to pass over the film with bending, so that the material is tightly laid on the glass, taking its shape. It will be easier for you to remove the protective layer.

After that begins the most responsible work of applying the film.

Tinting the Front Windows: Advice on Choosing and Applying the Film

Tinting the front windshields is one of the most popular procedures concerning tuning. It solves many problems, including weakening the bright sunlight shining into the eyes, and protects the glass from external negative factors. That’s why most car owners tend to tint their vehicle. However, in a special salon can take a considerable amount for such a procedure, so it will be more profitable to do everything with your own hands. Rules and recommendations on this subject can be read in this article.