How to make a lever on a tiller

How To Use A Tiller (FULL Tutorial)

Unit electrical system

Medium and heavy tillers are equipped with an electric generator that charges the battery and powers the headlight. The main function of the battery is to start the engine of the mini-tractor using an electric starter. On medium and heavy tillers, it is possible to connect several headlights (main and rear for a trailer), direction indicators.

The power of the working generator is sufficient for the installation of additional electrical equipment, as well as for the stable simultaneous operation of all electrical devices of the tiller. Manufacturing plants have provided for the possibility of additional installation of electrical equipment and equip mini-tractors with generators with a power reserve of about 30%.

The battery capacity corresponds to the starting current of the electric starter. Most mini-tractor models are equipped with generators without electrical excitation. It will be replaced by constantly rotating magnets. Most often, manufacturers install single-phase generators that produce alternating current.

How can you make a light on a tiller?

How to make a light on a tiller, because most models are not equipped with headlights? tiller (mini-tractor) is a mechanism that is designed for agricultural work (plowing, cultivation, watering, etc.). Many models can be used as a vehicle by means of trailers. In this form, tillers transport people and goods, which makes harvesting easier.

Self-installation of the headlight

If the unit was purchased without a lighting system, then you should not be upset. You can install it yourself. Some manufacturers sell a lighting kit (headlight, wires and switch) separately, earning extra money from this option, realizing that most owners will use the tiller as a vehicle. The engine has a special place for connecting the factory headlight It would seem that this is a little money in comparison with the price of a mini-tractor, but why spend it if the lighting can be made from improvised means?

Let’s consider in detail how to connect the headlight to the tiller. The first step is to find the lighting element itself. Almost every owner of the unit has another mechanical device (car, moped, scooter, tractor), to which additional headlights are attached. If this is not the case, then a used headlight can be purchased at disassembly points or in the automotive market to save money. If possible, it is best to purchase a new headlight, which can be matched to the color of the mini-tractor. A headlight for a small motorcycle or scooter is suitable for this.

It is necessary to purchase both a toggle switch and the required length of electrical wire.

The most convenient place to install the toggle switch (switch) of the headlight is the steering column near the gear lever.

We install and fix the switch. Next, we move on to installing the headlight. Find a place that’s comfortable for her. The front of the engine or steering column is best suited for installing this equipment. Experts advise to mount the headlight on the steering column tube, because the one placed on the engine will get dirty when driving in the rain. Next, we stretch the wires. If the tiller has a place for connecting the factory headlight, then we connect the wires to it, but if it is absent, then it is most convenient to draw the power from the terminal of the oil pressure indicator lamp. Next, we connect the wires to the switch, and from it we pull the cord to the headlight, using the tiller body as a mass. We fasten the wires with clamps or electrical tape to the steering column.

How do they plow the land with a tiller? How to properly plow with a plow on a tiller?

tiller is a versatile equipment with which you can plow the land, plant root crops, huddle potatoes and harvest. Such country equipment is not particularly expensive today, which determines its extraordinary popularity. Most often, tillers are used precisely for plowing the land for planting potatoes. There is nothing particularly complicated technique of loosening the soil with the help of a tiller. However, it is still necessary to know some of the features of this operation.

How to plow?

So, the tiller is ready. Now you can proceed to the actual procedure of loosening the soil on the site. To make fewer turns, plow the land with a tiller along the long side of the plot.

The tiller handle should be slightly turned at the base to the left. In this case, it will be possible to walk along the not yet plowed strip, which, of course, is much more convenient.

Well, now let’s figure out how the land is plowed with a tiller correctly. This procedure is performed as follows:

  • the tiller is installed at the beginning of the strip and goes along the stretched cord.
  • After the row has been passed, turn in such a way that the right wheel of the tiller is opposite the furrow of the already plowed strip.

Plowing should be done slowly. You should not push the tiller. If the engine overheats (and this happens quite often), work should be stopped for about half an hour.

Preparatory activities

We’ll talk about how the land is plowed with a tiller just below. To begin with, let’s find out what other preparatory measures, in addition to hanging wheels and a plow, need to be done.

Before proceeding with the operation of loosening the soil, it is worth pulling an approximate cord along the first row of the plot. Experienced plowmen may well skip this step. Beginners should definitely perform this operation. The fact is that in the process of plowing, any plow slightly leads to the right. And therefore, it is very difficult to make the row perfectly even. The cord will help you stay on course.

Starting from the second, all rows can be done without using additional guides, since the tiller wheel will follow the furrow.

What you need to know

When plowing the first row, the plow runs strictly vertically. However, starting with the second, as one of the wheels rolls along the furrow, the tiller, and therefore the share, tilts slightly. Therefore, the plow needs to be slightly shifted vertically in the opposite direction.

To do this, loosen the nuts in one of the adjusting grooves. After the plow is in the desired position, they are tightened again.

Plow attachment

This operation is quite complicated. it is best done with an assistant. To attach the plow, the tiller is raised slightly off the ground. To do this, he is driven onto some stands with a height of at least 15 cm. It is with this procedure that the preparation for operation of small-scale mechanization equipment intended for plowing the land, of any brand, should begin. Including such a popular one as, for example, the tiller “Neva”. How to plow the land correctly using the technique of this brand will be discussed a little below.

The hitch itself is made according to the instructions of the tiller and plow manufacturers. When performing this operation, make sure that the edge of the share touches the ground with the entire surface. The plow tine should be strictly vertical, and the beam horizontal.

Of course, the equipment should also be adjusted for the track gauge. To do this, you need to pay attention to how the plow share is located. Its right edge should be in line with the inside edge of the right wheel. In this case, the plow will cut the ground evenly and roll it off easily. The tiller himself will go easier.

What to do if the soil is too hard

Next, let’s take a look at how to properly plow the land in problem areas with a plow on a tiller. Normal soil is so loose that it can be easily pierced with a metal rod to the depth of a shovel bayonet. On too hard ground, the tiller usually starts to slip during plowing. In this case, the operation is performed twice. For the first time, the plot is cut to a shallow depth. In the second. to the fullest. Some “killed” areas have to be plowed in several stages. But this happens, of course, extremely rarely.

Very hard soil should be plowed wet. Then the plow will go much easier.

How to plow with a Neva tiller with a plow

Garden equipment of this brand among summer residents, due to its practicality, ease of use and low cost, is in great demand.

The capacity of the Neva trailers is enough for the hardest soil and even for virgin soil. In the latter case, not a plow is used, but special cutters. The grass must be mowed before starting plowing on virgin soil. You can also remove it using the tiller itself (if you have the appropriate attachments).

Actually, the answer to the question of how to plow the ground with a Neva tiller with a plow is simple. Of course, in the same way as using any other similar technique. The only thing experienced summer residents recommend is to change the oil in the tiller of this brand before plowing. Even if it’s still new.

READ  How To Plow Properly With A Tiller With Cutters

History [edit | edit code]

Alpha Java Edition1.0.1

Official Java Edition1.3.112w24a

1.513w03a

1.1317w47a

Alpha Edition Edition0.13.0build 1

Legacy Console EditionTU1CU11.0Patch 1

TU141.04

Added levers.
The lever can be installed on the lower edge of the unit (on the ceiling).
Levers can now be mounted to either side of the block.
Red dust particles are now displayed when switching the lever.
Added levers.
Added levers.
The lever can be installed on the lower edge of the unit (on the ceiling).

Data values ​​[edit | edit code]

Block states [edit | edit code]

Name Value Description facing

powered

north
south
east
west
The side of the block to which the lever is attached.
up_x Floor lever; the handle faces east when the lever is not activated.
down_x Ceiling arm; the handle faces east when the lever is not activated.
up_z Floor lever; the handle faces west when the lever is not activated.
down_z Ceiling arm; the handle faces west when the lever is not activated.
true Lever activated.
false Lever not activated.

Additionally [edit | edit code]

  • The orientation of the lever on the floor does not depend on the position of the player. it is random.
  • When the lever is turned off on the wall, the handle looks up, and when it is on, it looks down.
  • At the lever on the floor, if the handle is facing north or east, then it is off; south or west. included.
  • The lever cannot be placed on snow, ice, glass and foliage.
  • There may be a block of sand on the inverted lever. That is, the sand will stand in the air on the lever. It is difficult to do, but possible.
  • If you have an iron door, and you have levers on both sides of the wall, then to open this door you use the lever on one side. But to close the door with the lever on the other side, you need to put it in the position of the second lever, i.e. make it active, and only then close.
  • The lever can be used to change the direction of the rounded rails at the intersection.
  • The lever is a kind of T-Trigger.

Lever arm

Lever (eng. Lever). one of the types of switches.

Natural generation [edit | edit code]

Levers meet in the jungle temple.

Receiving [edit | edit code]

Levers can be obtained with any tool or with the help of your hand.

Block Lever Strength

Destruction time Hand

0.5
0.75

Crafting [edit | edit code]

Using a generator

If the unit is equipped with its own generator, then the solution to the issue of arranging lighting is greatly simplified. You just need to install the flashlight and supply power to it.

To do this, you will need the following tools and devices:

  • electric drill;
  • soldering iron;
  • screwdriwer set;
  • spanners;
  • nippers;
  • stationery knife;
  • electrical cable;
  • heat-shrink tubing;
  • headlight, side and turning lights.

Installation of a headlight on a tiller using a standard generator is carried out in the following sequence:

  • The bases of the lighting fixtures are screwed to the body of the unit. It is advisable to put the headlight on the tiller on a separate bracket located on the front part with an elevation above the ground of 100-120 cm.
  • On the steering column we install buttons for turning on the lamp, turning and side lights. You should choose devices of increased strength, in a waterproof design. Fixation is carried out with clamps or self-tapping screws for metal.
  • The electrical cable is pulled into a corrugated tube. This must be done so that the wiring is protected from moisture, mechanical damage and rodents. The corrugated tube is pulled to the steering column and frame so that there is no sagging.
  • The wires are connected to the generator and the terminals of the electrical equipment. The engine is started and the lighting system is tested. After that, all twists and joints are insulated.

When idling and at low speeds, the light dims. To keep the lighting constant, you need to use a voltage regulator or install a powerful generator.

Electric generators from MTZ tractors and ZAZ cars have proven themselves well.

These devices are compact, they can easily find a place on the body of the cultivator. To connect a non-standard generator for a tiller, you will need to make an additional bracket. It is assembled from a steel corner on the frame of the machine (there are many videos available on the Internet with a detailed description of the manufacture).

Battery lighting

You can make a light on a tiller without a generator by installing a 12 V battery. The battery from a motorcycle, moped or boat is taken as a power source. Don’t give up your car battery. If you put a heavy power source on the cultivator, then you can solve several associated problems. equip the unit with an electric starter and significantly weight its body. In addition, it will be useful to be able to illuminate the area at night without the engine running. This feature can come in handy for a picnic or night fishing.

Installation of a headlight on a tiller using a battery is carried out in the following sequence:

  • Arrangement of the frame for the power supply. It is best to use a steel corner for this. The frame should be fixed directly to the frame of the motor cultivator body. After lowering the battery into a niche, it is firmly fixed in it using steel straps.
  • Attachment of a lantern and auxiliary lights. The headlight on the tiller is placed so that it illuminates the widest possible sector without dazzling the operator and oncoming vehicles. It is better to choose devices with an adjustable angle of illumination.
  • The location of the electric cable in the corrugation along the unit body. Installation and connection of control devices. Checking the correct assembly of the electrical system with a tester.
  • Connecting the wire to the battery terminals, leading the wire to the junction box. Connection of wires to the switch, insulation of joints, joints and twists.

In order for the battery capacity to last for a long time, LED lamps must be inserted into the lanterns. They consume negligible amount of energy, creating bright lighting.

If the battery is not located under the standard hood of the tiller, then it is necessary to make a separate casing. To do this, you can take a piece of dense plastic, give it the desired shape and screw it to the homemade racks on the frame.

When deciding to install a battery, you should consider recharging it. To do this, you will need to purchase a charger or install an electric generator on a motor-cultivator.

How to make a light on a tiller with your own hands

The question of how to make the light on the tiller has to be decided by everyone who purchased this unit without a standard headlight. Today, most models of domestic and foreign production are designed to work only during daylight hours. And those that have a built-in flashlight do not always provide high-quality lighting. The factory headlight illuminates a narrow sector in front of the car and quickly becomes dirty. Ready-made kits are on sale that can be installed on the Tiller Neva, Plowman, Volgar, Forza and other domestically produced units. With an average quality, such sets are expensive. You can save well if you make a light on the tiller with your own hands. With a headlamp, the cultivator will become much more functional and more convenient to use. Consider the options for how to connect the headlight to the tiller.

Light without battery and generator

When deciding how to make a headlight for their tiller, most make the most difficult technical decisions. Making a light without a generator and battery can be simple, fast and inexpensive if you use bicycle lights. This option can be used as the main or alternative light source for any motor vehicle: tiller, cultivator, lawn mower, snow blower. A properly sized flashlight can also be fitted to a motorized dog, towing vehicle or snowmobile.

Bicycle lights have the following advantages:

  • no need for wiring;
  • minimum financial investments with high efficiency;
  • reliability in all weather conditions;
  • availability of its own charger for portable batteries;
  • the ability to mount on the steering column on the brackets that come with the kit;
  • quick removal for manual use or for charging.

It costs two bike lights to purchase. It is advisable to use one for the main beam, the second for lighting directly in front of the unit.

How to make light on tiller MTZ-09

Tiller MTZ-09, like many others (for example, Neva, Zubr, Agat), is not equipped with a headlamp for working in the evening and at night. If necessary, lighting can be made and installed by hand.

To make a headlamp for MTZ-09, MTZ-09n or any other tiller on your own, you will need:

  • electrical wire;
  • LED or halogen bulb (optimal power. 5 W with a minimum angle of light scattering);
  • a body from a faulty energy-saving diode lamp, or from a small bicycle headlight;
  • household switch or toggle switch.

To connect the lighting to the tiller, you can use the algorithms proposed above: through a battery without a generator, or using a standard generator.

From ignition

An alternative version of the light on the tiller with your own hands without a generator is to connect to the ignition contacts. Each time after starting the engine, power will appear and the installed headlight will light up. The main disadvantage is the inability to turn off the equipment until the tiller dies.

When considering options for how to put a headlight on a tiller from the ignition, they think about the convenience of using lighting. It is necessary to consider additional elements that will allow you to turn off the light when parking, regardless of the state of technology.

Connecting to the ignition contacts. an alternative version of the light for the tiller

How to make a headlight on a tiller?

As a lighting on a tiller, many owners of special equipment install headlights of domestic and foreign cars. This option is expensive and unreliable. There is not enough outgoing light, and the system itself will not last more than a few months. Alternatively, they develop a headlight for a tiller with their own hands, which allows you to get the necessary lighting and equipment power.

READ  Gasoline in the crankcase of the tiller engine cause

Step-by-step instructions for making:

  • Purchase an old, inexpensive headlight. Equipment from Soviet cars is suitable.
  • Remove the glass protection and other elements fixed with plastic fasteners from the device.
  • Pour the dummy headlight using plaster, for which the finished material is poured into the device and remains until completely dry. After that, you can remove the cast, preserving its integrity.
  • The resulting template is applied in three layers of fiberglass, each time treating the material with epoxy resin. After processing, the future headlight must dry under vacuum.

Many owners install the headlights of domestic cars as lighting on a tiller

  • Then they start making glass on their own. This will require an oven, special slats and fiberglass. It is necessary to make a platform from the rails, which is placed in a preheated oven up to 180-200 C °, where fiberglass is placed without a protective film.
  • When the material begins to deform, it can be pulled out and applied to the finished workpiece. After pouring out the mold, it is necessary to place the future headlamp in a vacuum.
  • After complete cooling, the product is sanded with sandpaper.
  • The final stage is the installation of electrical equipment, installation of the lamp.
  • Before using the headlight in the tiller, it is necessary to check the operation of the device and the absence of short circuits several times in order to avoid damage.

    How much adrenaline is in your blood

    Therefore, it is necessary to think over a number of steps in advance:

    • used electrical circuit;
    • way of power supply of headlights;
    • the right choice of light.

    Lighting on the tiller can be done by yourself

    For tillers with belt drive

    A feature of technology with a belt drive is the absence of a generator. Therefore, the owner of the special equipment must independently install the electrical equipment with the help of locksmith tools and additional spare parts. They can be removed from a car or other equipment.

    The main thing during installation is to replace the alternator pulley with one that matches the tiller‘s belt drive. For greater convenience, the electrical equipment is attached at the back, after which its operability is checked and the lighting is connected.

    The absence of a generator is a feature of the belt drive technology.

    DIY headlight installation options

    After making the headlight and preparing the tools, they proceed to installing the light on the tiller.

    The choice of the source of electricity is one of the main tasks when installing the headlight yourself.

    Step-by-step instructions for performing:

    • Conduct wiring from the electricity source to the headlight, check the system is working and the brightness of the light.
    • Install the switch in a convenient place for use, and then integrate it into the headlamp power circuit. Only one wire goes from the button to the light.
    • At the final stage, they turn off the power supply and proceed to the installation of protective elements, corrugations, as well as fixing all the parts on the equipment. Without heat shrinkage and additional means, lighting can be damaged or fail.

    One of the main tasks when installing a headlight yourself is choosing source of electricity. Usually use a generator, battery or ignition.

    Necessary tools for the job

    Before starting work, it is necessary to prepare all materials, including wiring, headlight, corrugation, and also assemble a set of tools:

    • soldering iron;
    • screwdrivers and wrenches;
    • nippers and stationery knife;
    • electrical tape and heat shrink tubing;
    • electric drill and fasteners.

    For heavy tillers

    In heavy tillers, generators and belt transmission are not used, therefore, rechargeable batteries are used for the light source.

    It is recommended to install batteries from motorcycles, since they have sufficient power, small dimensions and weight.

    The only drawback is that you need to make and fix the battery holder yourself. For this, an iron profile or corners welded into a single structure are suitable. And for greater reliability, the product is treated with a soft material, after which the battery is attached.

    Specificity of selection and installation of lighting

    Before installing the headlight on the tiller, you need to decide on the equipment used. The choice of a lamp for lighting depends on the complexity and nature of the work being carried out, as well as the lighting requirements.

    The more light is needed at night, the more power of the selected lamp should be.

    Also, there are technical features when installing headlights. If the power of the generator is not enough to provide a constant flow of light, use 12V batteries. It is recommended to use light equipment so as not to increase the load on the tiller.

    Without generator

    Another method of connecting lighting is widespread among operators. Here it will be possible to do without using a generator. You will need a 12 volt battery and LED strip.

    There is no need to specially purchase a new battery. For this purpose, you can use an old electric scooter battery.

    In addition to the source code, you must think in advance where this device will be mounted. If you are the owner of a large vehicle, then the ideal solution would be to install a battery between the gearbox and the engine.

    Step-by-step actions:

    • Using welding and an iron angle, you need to make a stand for your gel battery. It is attached to the frame of the mini tractor.
    • A battery is installed from the inside, which is clamped by a pair of bolts and a metal insert.
    • Wires are laid from the battery to the power button. All joints must be sealed and insulated with heat-shrinkable tape.
    make, lever, tiller

    This kind of lighting will turn out to be very bright. However, this method of installing headlights has one negative side: a full charge of the battery is enough for literally a couple of hours of operation, after which it will need to be recharged again. This is a very significant disadvantage for those who work intensively with a mini tractor.

    With your own hands

    Almost all owners of tillers resort to using headlights from Soviet light vehicles as lighting equipment. This is one of the easiest ways to solve the problem.

    But do not forget that such a light will not be bright enough, and it is unlikely to please you with a long service life.

    Therefore, the best option is considered to be the independent manufacture of such electrical equipment. You do not need to purchase expensive sources and equipment. All you need is the same headlight from a Soviet car. You will only replace the inside.

    So, to begin with, the outer glass and other elements, fixed with plastic clips, are removed from the headlight. The next step is to make a dummy body of the lighting device. It is made of plaster. Liquid gypsum is poured into the base of the fixture and spread evenly over the entire base. Wait until the plaster is completely dry, then the impression must be carefully pulled out.

    Please note that experts do not recommend artificial drying, so it is better to wait until the gypsum hardens naturally.

    make, lever, tiller

    Three layers of fiberglass should be applied to this template. Be sure to apply epoxy between coats. It is inexpensive, on the market it.

    After all the steps taken, your workpiece should lie at room temperature in a hermetically sealed container, without air penetration. Wait until the dummy is completely dry. Next, you will need to grind the product so that there are no irregularities on it.

    Now comes the most important step. you need to make glass. To do this, you need to heat the oven to a temperature of 180-200 C. Buy thin slats in advance and make them a stand. The manufacture of such a structure will require about 10 rails. Then attach the fiberglass to it. Remove the protective layer of the material. Otherwise, the workpiece will absorb all the dust. You can send the workpiece to the oven.

    Open the oven periodically and check the product. As soon as it begins to deform, you can take it out and apply it to the material that was prepared a few steps above. All this is again sent to a sealed container with a tight-fitting lid. Wait for complete hardening.

    Do not immediately install the lighting fixture. Previously, it must be checked several times for short circuits, and only after that the headlight can be attached to the tiller. Do not use a suspended structure to install it. Such a light source must be fixed in at least four places.

    Power generator

    After you have built the main part of the light source, you need to connect it to the generator. You can use any standard electric generator from a mini tractor. For this purpose, many trailer manufacturers produce vehicles with excess capacity. This power is just spent on lighting and installing a car signal.

    Such an electric generator is more than enough for a given light source.

    To equip the tiller with lighting, just follow the steps below:

    • First of all, route the wiring from the generator to the headlight.
    • Install the power button near the steering wheel, or in another place convenient for the driver. A wire is also removed from it and connected to the headlamp. Check the quality of the lighting and the operation of the power button.
    • If all is well, then disconnect all wiring. The wires should be protected with a corrugation. Otherwise, you could inadvertently pick up and damage them. Also, without protection, the possibility of water ingress and short circuit is not excluded.

    If the generator is powerful enough, you get very bright lighting with a high beam. The low power of the generator may be indicated by the constant flashing of the headlight at high loads on the tiller. If you are faced with just such a situation, then a reasonable solution would be to replace the standard unit with an electric generator from any tractor made in Minsk. Its power will definitely be enough for you.

    Do not forget that if you are installing a third-party electric generator, then standard mounts will not work for it. You will have to cook additional ones. Lighting coil is used for connection.

    READ  How to Make Teeth on a Saw

    After successful installation, check the wiring. Get in the habit of checking your contacts every time you work with a tiller. Otherwise, moisture may enter, which will affect the operation of the tiller as a whole.

    How to make a light on a tiller?

    • With your own hands
    • Power generator
    • Without generator
    • From ignition

    In the modern world, all mini tractors are very well equipped. Despite this, not everyone has lighting equipment. However, solving this problem will not be difficult. Everyone can put a headlight on a tiller without having any knowledge of electrical engineering. Everything is done very simply and according to the instructions.

    From ignition

    This is the easiest way to create a light source. You need to route the wire with one end to the ignition and the other to the headlight switch. Such a light source will work stably. This connection method also has a disadvantage: with the ignition off, you cannot turn on the headlight.

    All of the above lighting installation options are compatible with absolutely any brands of tillers and mini tractors manufactured both in Russia and abroad.

    How to make a Tiller for bow making, a quick guide

    To learn how to make light on a tiller, see the video below.

    How to reverse speed on a tiller

    Let’s take a look at how to reverse the speed on the trailer. The presence of a reverse depends on the model and dimensions of the mini-equipment. You can cultivate the land with a motor cultivator, a light tiller and a heavy machine. It all depends on the goals and objectives set. Usually, when using models weighing up to 30 kg, there is no need for a reverse speed, moreover, it complicates the design of the unit. On a heavy machine without this function, it will be more difficult to do the job.

    Agricultural machinery will not move without a gearbox. It happens:

    • angular;
    • gear;
    • downward;
    • reverse gear.

    The task of the bevel gear is to ensure the collision of the transmission with the engine, which affects the power of the gear. The gear is the transmitter between the motor and the wheels. The reduction gear serves to reduce the speed to increase power.

    The reverse gear has a clutch located between the gears. They are on the main roller. The main task of this system is to ensure the reverse gear of the equipment. To make this mechanism yourself, the first thing you need to do is prepare a case, for which many use a two-inch fitting square.

    You can use the generator shaft from the Ural motorcycle. The gears will fit from the Friendship chainsaw. In the shaft, you just need to drill a hole of the appropriate diameter. Mount another pinion shaft with bearings on the opposite side. And already on the weekend, fit a pulley to ensure rotation.

    You can purchase a ready-made gearbox, only when buying it is better to give preference to more expensive mechanisms, since they are more reliable and last longer.

    Among the malfunctions of gearboxes, users highlight the rapid wear of the gears and the fact that the transmission takes off.

    If you increase the speed of the cultivator, then you need to take into account that wear will occur much faster. When doing land work, I want to quickly cope with the task. To increase or decrease the speed of movement, you can try the throttle stick. If the work is hard, then when the gas decreases, the engine will stall.

    The first speed is used when plowing the land when more power is required from the machine. Faster work reduces the depth of cultivation.

    How to reduce the speed of a tiller

    To solve certain tasks (plowing virgin lands and heavy soils), some models of tillers may be too fast, in which case it is necessary to reduce the speed.

    Without resorting to changes in the equipment itself, you can use the crawler gear, which is present on many models. This option allows you to reduce the speed without reducing power, allowing you to work the soil more thoroughly.

    To reduce the speed, you can reduce the diameter of the wheels or replace the gear pair in the wheel reducer by changing the gears. Gears of different sizes are usually installed, with the number of teeth of 61 and 12, in order to reduce the speed, it is necessary to replace them so that the number of teeth on the larger sprocket increases.

    Tiller maximum speed

    Many owners are wondering: what is the fastest speed possible on a tiller? The answer depends on many nuances, mainly on the tiller model. It is also important to consider that the working speed is lower (2-4 km / h) than the speed of the tiller when transporting goods. In the event that the working speed is increased, some types of work will be more difficult, as the control of the tiller will become very difficult for the operator. If the tiller is used as a vehicle, then its speed can reach 30 km / h.

    How to increase the speed of a tiller

    There are two ways to increase the speed of a tiller:

    • installation of large wheels;
    • replacement of a gear pair.

    Let us first consider how changing the wheels helps to increase the speed of the cultivator. The standard wheel size of almost all mini-unit models is 57 cm. When changing, tires that are 1.2 times larger in diameter can be installed. Usually wheels of 70.4 cm are used. Despite the small difference, the speed of the tiller increases markedly. If the arches into which the tires are inserted will allow you to insert wheels with a large diameter, then you can try adding centimeters.

    Let’s consider how to increase the speed on the tiller in the second way. Like any technique, the cultivator has several speeds, which are controlled by gears. Usually cultivators move at a speed of 2 to 15 km / h, while the large gear has 61 teeth, and the small gear has 12. To increase the speed, the gear pairs of the reducer are replaced. We increase the number of teeth, thus reaching the maximum speed of the tiller.

    It is recommended that the replacement be carried out by professionals and preferably in specialized centers, since parts turned with a minimum error will affect the operation of the motor. It is not only the replacement of the gear that is important, but also the correct selection of the pulley.

    Ways to increase speed on a tiller

    Many farmers are wondering how to increase the tiller speed. The most common agricultural technique is the tiller. With its help, the performance of work on land and personal plots is greatly simplified. Let’s consider how you can increase the speed on this technique. With the increased speed, the productivity and cross-country ability of the mini-car will increase, which can be used in any season and weather.

    Best Speed ​​Tiller Models

    A fast tiller is an indispensable assistant when transporting goods in rural areas or when working over a large area. Diesel tiller Centaur MB 1081D is the fastest among heavy class tillers, can reach speeds of up to 25 km / h. Tiller Motor Sich MB-6D has a maximum speed of 16 km / h.

    Popular models of tillers from domestic manufacturers have a much lower maximum speed. on average, 12 km / h for MB-2 and MB-23, Neva. The tiller Mobile-K Cheetah also has a good speed. 12 km / h (gearbox 41).

    What is the speed of the tiller

    Tiller speed depends on several parameters:

    • tiller class
    • engine type
    • availability of attachments
    • type of gearbox
    • wheel size
    • the area where the tiller works

    As a rule, the tiller class is associated with the type of engine, light models are equipped with gasoline engines with a capacity of up to 5 HP, medium ones. with gasoline engines 6-12 HP, heavy ones. with diesel engines with a capacity of 12 HP or more. Diesel engines are more powerful, so equipment with such engines will have a higher speed.

    Among the budget models of middle class tillers, the type of gearbox is 2 forward, 1 reverse, more expensive models have 6 forward and 3 reverse gears. The more gears, the higher the speed is available.

    Wheel size matters: the larger the wheel diameter, the faster the equipment moves.

    Attachments such as plows, mowers can reduce speed. A tiller with a trailer will also have a lower speed, although it is possible to accurately calculate the speed with a trolley only when taking into account the speed and weight of the tiller itself, as well as the weight and type of the cart. Usually the speed of a tiller with a trailer does not exceed 10 km / h.

    The more difficult the terrain, the more the speed decreases. For plowing on virgin soil, it is recommended to use weighting materials that ensure passability and help maintain speed. However, it is worth remembering that plowing heavy land at high speed is not recommended, as the quality of land cultivation decreases.

    Do-it-yourself speed increase

    How to make your tiller faster? It should be noted that we are talking about transport speed. Tiller Neva MB-2, with certain modifications, can reach speeds of more than 20 km / h, however, if it does not have a differential, then control becomes much more complicated.

    You can increase the speed in several ways, for example, put wheels of a larger diameter or change the gear pair of the wheel reducer, replacing the standard gears with 61 and 12 teeth 55 and 18, respectively. This method is quite difficult to implement, but it allows you to increase the initial speed by almost 2 times.

    Some owners want the tiller to drive at 40 km / h. It is possible to make such a modification, but it must be borne in mind that there will be a large load on the gearbox, and it will be difficult to drive such a vehicle.

    What tricks did you use to change the speed on the trailer??

    Replacing the Carburetor on a Mantis 2-Cycle Garden Tiller / Cultivator