How to run a new motorcycle. Error 6. Use fuel with additives

Playing a two.Stroke engine of a trimmer for grass (benzokos)

The use of gasoline cobs is due to the need to process adjoining or garden territories, open areas. In the process of use, on a benzoocos, and in particular its mechanical nodes, there is a large load on the part of internal and external factors. For the tool to work as efficiently from the very beginning of the purchase, and for a long time does not break, it is necessary Playing Motokos gasoline Before starting use. This is done in stationary conditions with a trained specialist or the owner of the product, since there are no difficult operations in the process. The main thing is to know how to correctly carry out the location of the gas instrument, so as not to entail errors. You can also turn to this issue to specialists who sell you a new not.So.Rolled braid, or performing a major overhaul to replace the drive nodes.

Explaining whether your tuning is needed, we will highlight the advantages of such an event:

• The new tool is evenly lubricated;
• Grinding all parts is performed;
• The product smoothly goes into working mode;
• A comfortable examination of the tool is performed in case of identifying the need to regulate the interaction of mechanisms to stabilize work processes.

The last paragraph also allows you to check the quality of the engine when running after overhaul, when smooth commissioning also takes place. In a similar gender, running in the same time is performed after the spare parts for motorcycles in the engine, gearbox and other mechanisms have been changed.

Peculiarities

It should be noted that the gasoline braid is controlled very simply. It is enough to see how other users use this unit to start using it fully. The performance of the main technical functions is intuitive and does not require any difficulties in practice. It will not be difficult to run the gasoline trimmer correctly. Over, there is almost no difference between devices of household and professional categories.

The key difference is the type of motor. On technology for professionals, it is more powerful and gives more revolutions. A two.Stroke engine is more often used in household models. Four.Stroke units are more reliable and give out a greater effort, so they are suitable for special conditions, difficult and overgrown sites.

How to run in parts?

The described launch method is quite suitable even for Chinese technologies. But sometimes it is impossible to start the first time or the trimmer stops immediately. In this case, similar manipulations are performed when closing the air duct valve. If then nothing works, you need to contact a specialist. If the system works correctly, never start the device immediately.

Read set for changing oil in lawnmands

First, the engine should work at idle for 5 minutes. Important: if the instructions indicate another time, you must follow its instructions. During heating, it is necessary to adjust the air supply. Setting various provisions of the air damper lever, they guarantee that the cutting part is not moving. Having waited for warming up, completely open the damper and set the power by 50% of the maximum.

In this position, the lever is held within 20. 30 seconds. Having lowered the gas to a minimum, let the braid work 30-40 seconds. Then they set the power by 20% and wait 10-15 minutes. After that, the engine turns off and remains at rest for ¼ hours. When the trimmer cools down, the engine starts in accordance with the already described scheme, but first the damper opens.

Gas maintenance should be avoided, since poorly processed parts can be damaged. Long idle is also contraindicated. This will lead to overheating. This completes the engine operation, after which you need to start the transmission. This procedure is performed on an open area where soft fresh grass grows. It is mowed by 5. 10 minutes without a break, periodically processing gases with a capacity of 50-75%.

After such a session, the mowing stops for 20 or 25 minutes. Typically, 3-4 cycles are enough for the correct operation of the trimmer for many years. Most often they try to start the device until the first refueling is completed.

Features of Kustorez See in the next video.

The correct first launch and launch of a bush cutter are very important steps when starting a new tool. On the one hand, they can save a gasoline engine motorized engine, laid down by the manufacturer, since at this stage there is a crushing of mobile units and parts. On the other hand, the first necessary skills for working with a trimmer are acquired when we are talking about the first tool in my life.

• Preparation for the first launch of a bush
• Examination and lubrication of the gearbox
• Preparation of the correct fuel mixture
• The first trigger
• The start of work on starting brushes for gasoline

Preparation of the correct fuel mixture

Before starting to run into a new engine, a benzokos, it is also necessary to prepare the fuel mixture correctly. As you know for two.Stroke engines, it is prepared from special two.Stroke oil and gasoline, taken in certain ratios. You can find out proportions from the instructions attached to the tool, or on the labeling label. From the instructions you will also learn the recommended type of fuel, as well as the recommended type of motor oil.

Having gathered to run into a new gas station, many are faced with the problem in the preparation of the fuel mixture. And the reason for this is the disagreement in the instructions of the tool manufacturer and in the instructions of the manufacturer of motor oils. The first recommend a 1:25 proportion. The latter recommend 1:50. Who to believe? How to proceed?

See also: The rating of the best electrocos and benzos: features of devices, which is better and what is the difference

According to experts, if in the instructions for a motorcycle, manufacturers write a proportion of 1:25 or 1:30, then it is most likely a cheap tool with poor cooling, or the manufacturer does not know what kind of oil will be added to the consumer. But here it must be understood that the excess of lubricant does not affect the performance of the trimmer in the best way. Excess oil does not completely burn out when operating the engine. It cokes, clogs a cylinder and piston.

What to do in this situation when running in a new tool? An ideal option would be to purchase exactly the oil that the manufacturer of the benzocouses recommends. In the case of run.In engines, when it is not possible to purchase the recommended oil, it is best to purchase a good Husqvarna two.Stroke oil for the same gas tool. It costs not cheap, but there is enough it for a long time. It is necessary to interfere with it as it is written in the instructions on the bank.

Inspection of the gearbox gas.Cosse and its lubrication

Checking the gearbox before starting a gasoline trimmer must be carried out on a regular basis. The lack of lubrication or its small amount increases the friction of the gear gear of a gearbox operating at fairly high speeds. As a result, overheating and gears occurs. Motokosa gearbox fails. To prevent the occurrence of such a breakdown during operation and the regular inspection helps.

If, before the launch of a gasoline braid, an insufficient amount of lubrication in the gearbox or its absence in the case is laid “Litol”. To do this, it is necessary to unscrew the screw on the bend of the gear housing and the “lilest” in the amount of 1-2 ml.

Working with a gasoline trimmer for a long time, every 8-10 mothers add grease to the gearbox of the bar.

How to start a motorcycle

The peculiarity of any technique with a two.Stroke engine is a hard algorithm of cold launch, which must be strictly observed.Good afternoon, dear subscribers and guests of the channel.

The other day, a man asked me to see his mower.

The complaint was that the tool would not start. The client said that he bought a mower recently, worked only once. An attempt to start a motorcycle for a second time was unsuccessful.

Such leaks indicate that the mower shifts fuel, but the user practically did not work, and as I later found out from the client, they appeared during an unsuccessful launch.

Now everything fell into place. This motorcycle is completely serviceable, but the client would not be bad to read the instructions, especially the section in which the process of “cold” launch is described.

How to start work?

The literacy of the first launch largely depends on how a gasoline braid will show itself with further operation. Errors can lower the device of the device. The fact is that after starting the moving mechanisms of the working apparatus will be rubbed to each other. Additionally, the skills of using the trimmer are formed. This is very important in cases where they work with this technique for the first time.

Start by examining the gearbox and the quality of the coating with its lubricant. Then the fuel mixture is prepared according to the instructions.

Having noticed a lubrication deficiency or its absence, you need to add a portion of “lithol”. The procedure is carried out very simply: a screw located on the bend of the gear housing is twisted. Through the released channel, 1-2 ml of lubricant is added by a technical syringe. With everyday work with a trimmer 1 time in 8-10 hours, you will have to lubricate the gearbox of the bar.

But the roller.Tank is not exhausted only by laying the oil.

Two.Stroke engines need a combustible mixture of two.Stroke oil and gasoline. It is prepared in the proportion indicated in the guide to the tool or on the lubricant label. The preparation of fuel should be carried out a little so that only one mowing is enough. You need to place a fuel supply in the next container:

It is recommended to pick up oil with a medical syringe. This will more accurately observe the dosage. Sometimes another question arises. The manufacturer of the tool and the manufacturer of motor oils indicate different proportions of the combustible mixture, so it is difficult to decide which instructions to follow.

After the tests and pouring of the fuel mixture, such manipulations should be done:

We start running.In gas troops

After starting, do not rush to immediately run the trimmer. Let the engine idle for 5 minutes. While heating is going on, adjust the air supply to the air damper with a lever so that the rogue with a trimmer line or with a knife does not rotate. As soon as the tool warmed up, we completely open the air supply to the corresponding lever to the “ON” position and squeeze the gas trigger for 1/2 and hold the seconds of seconds 30. Then we drop the gas, let the trimmer work on xx 3040 seconds. In this mode we continue 10 minutes 15. Then we mock and let it rest for 15 20 minutes.

Stp fuel system cleaner did the impossible!

By cooling the benzokos, we continue to run the engine according to the previous scheme. Start hot, trimmer should already be with an open air damper. Try not to hold the gas for a long time, since the movable details of the tool only rubbing each other. And do not let the engine work at idle for a long time as it can overheat.

The next stage is the running.In the gearbox of a gasoline braid. To do this, select a plot with soft young grass. Kosim 5 10 minutes with 1/2 2/3 from full gas. After we take a break for 20 25 minutes. Repeat the cycle 3 4 times.

Generally Running Benzokos for the described algorithm is made until the fuel mixture in the tank is fully production. After which the tool is ready for long.Term work. In the process, follow the temperature regime of the gearbox and the motor. They should not overheat.

Motokosa service (trimmer)

Engine. The air filter should always be clean (without dirt or sawdust); foam filter must be wetted with oil. The fuel filter must be checked once a week, in the case of intensive use of the tool, if necessary, to replace it in time. Checking the tightening of nuts and screws. Before starting work. Cleaning from a muffler carrier (or its grid) and candles. If necessary.

Cutting discs. The cutting faces should be well and properly sharpened using the necessary templates and files (emery), in compliance with the angles of the cutting parts depending on the brand of the disk. Double.Sided disks regularly turn over 180 ° and wear out evenly. A dumb disk or a disk with poor or improper sharpening does not cut well, and thereby overloads the engine, which leads to an accelerated reduction in its motorcyclear.

Flacks and trimmer heads. Use only a special braid trimmer line. Do not use wire or metal cables! Install a trimmer line only of the diameter that is recommended by the manufacturer. Wind on the bobbin tightly, but do not cross the turns. Clean the mowing head from dirt and, if necessary, lubricate. A worn or deformed head can disable a gearbox and/or shaft motorcycles.

Corner gearbox. As necessary, cleaned of dirt (such a “fur coat” does not allow the gearbox to cool normally) and add a consistent lubricant of Husqvarna, or similar, for a reducer pair.

Protective covers. It is forbidden to work without a protective casing. This is dangerous for the life of the operator and others, and can also overload the motor motorcycles. For each type of cutting equipment, only its own protective casing, provided for by the manufacturer, should be used.

Independent repair of motorcycles

It should be noted that it is not always possible to independently repair motorcycles, but in most cases, small repairs are possible for everyone.

If the trimmer motor broke, but you are not a car mechanic and not an electrician, it is better not to try to fix the mechanism. There is a chance that you cannot collect it back. There may be such problems: low compression in the engine, the engine jammed, the carburetor failed. If these phrases do not tell you about anything, then you should not repair the motorcycle for the picture and intuition.

It should be noted that the maintenance and repair of the chainsaws and motorcycles are largely similar.

The trimmer consists of a bar, a motor (happens from above or below), and a mowing head with knives, various additional elements. What can be repaired here yourself?

Air damper; 2. Handle; 3. Engine stopping device; 4. Throttle control lever;

5-bracket limiter; 6. Bar; 7. Protective device of cutting devices;

1) If the swallowed a toggle switch is turned on, and you are familiar with simple electrical circuits and are friends with a soldering iron, solder and rosin, then you can easily replace the toggle switch with a new. They are sold in electrical equipment and lighting stores.

2) if the wire limiter with braid head, It can be wrapped with flexible copper or aluminum wire to the bar. You can also make a new mount from a strip of stainless steel.

Sunday Bike Market | Largest Bike Market of Karachi Pakistan

3) if the trimmer line is torn in the drum braid head. There is nothing easier than replacing it on your own. You can, of course, just buy a head for motorcycles separately and replace it, but the trimmer line will cost a hundred percent cheaper. The optimal material here is a trimmer line from 0.9 to 1.5 mm, nylon or nylon. Measure the diameter of the used trimmer line at once, before it ends completely. Thinner. Can break, thicker. Causes engine overheating and unnecessary vibration. You need to disassemble the drum and wind the trimmer line manually, then collect the drum.

4) if the bar breaks, it can also be repaired by scraping and gluing to wooden rails or iron brackets.

5) If strong vibration has begun, and the engine began to work “unevenly”, perhaps a motorcycle has a lubricant. Any trimmer is easily disassembled, it is recommended to lubricate it with technical oil at least once a year.

7) if the trimmer is equipped with plastic knives, and they were deformed for some reason, there is a way to replace them with metal. To do this, you need to make several stainless steel knives. This is difficult at home, but a familiar turner operating in an industrial enterprise or factory will be able to save the situation. Knives are attached to the shaft using a sleeve with a puck. Such modernization will lead to the fact that a trimmer will become possible to mow grass of any stiffness. But caution when handling such a trimmer should increase.

8) the engine does not start? To start a braid, sometimes even hot, it is necessary to completely close the damper to enrich the mixture. Check the flow of gasoline, clean, if necessary, replace the glow of incandescent.