Replacing the starter cord motokos Patriot. Typical malfunctions

How to put a starter on a trimmer for Patriot grass

One of the key parts of the Kustorez is a starter designed to facilitate the start of the device engine. Like other parts, it breaks periodically. In this case, there are two solutions to the problem: to repair a trimmer for the starter’s grass or replace it completely. The second option is simpler, but more expensive. In addition, on sale you must first find the necessary part, since different models of lawn mowers use different starters. If you have free time and a screwdriver with an appropriate tip, you can restore the performance of this device, if you know how it works, what defects are characteristic of it and how to fix it. All this is in this material.

In order to independently fix the gasoline starter, you need to understand the principle of its operation and know its device. To date, trimmers for grass have manual and automatic starters, and the first. the most common

Part is a plastic case in which a pulley with a cord wound on it is placed to start the engine. In order for the cord to be wound independently after winding the tool, the steel belt is located inside the pulley. A rattle is installed on the front of the pulley, which blocks the starter on the drive shaft of the tool motor.

The note! Depending on the model and brand from which a trimmer for grass is made (Huter, Husqvarna and other brands), the ratchet can consist of one or two separate components.

The principle of the manual starter is the same for Chinese, European and domestic production of a gas trimmer for grass, whether it be Hitachi, Patriot or another manufacturer. To start the engine, the owner of the device abruptly pulls by the cord. The pulley rotates from this movement, and the protrusions located on it enter into the hook with dogs located on the flywheel. Then the flywheel and crankshaft begin to rotate the pulley. After starting the engine under the influence of the centrifugal force, the crests and dogs diverge in different directions. And after the user releases it, the starter cord is wound on the pulley using a return spring.

Important! With intensive use of the drive cord, it breaks over time, and the spring wears out. These details are easy to replace with your own hands.

Signs and reasons for the failure of the starter

In rare cases, the executive mechanism breaks when the tool is inaccurate. The consequences can be unpleasant: a deformed cord is wound on a flywheel of a working engine, a pulmonary pulley and a spring break but these are isolated cases, a complete replacement of the starter is rarely required.

The main malfunctions of the trimmer for the grass of the starter

It is easy to determine the reason for the refusal of the starting device. There are several main options:

Perhaps the starter mechanism is accidentally broken. The consequences will be deplorable if the wrapped cable is wrapped around the flywheel of the internal combustion engine: then the spring will burst and the pulley will break. But such cases when a complete replacement of the starter is required are extremely rare. In most cases, it is enough to fix a new spring or replace the cord to fix the mechanism.

You should make sure that the spring does not injure the owner in case of accidental departure.

Starting analysis

Disassemble the starter mechanism to install new parts instead of broken in the following order:

• unscrew the screw, fastening the pulley using the starter cover using a screwdriver;
• Remove the spring and antennae;
• Carefully remove the pulley (you need to turn your head or practice, after putting on your glasses and gloves);
• determine why the trigger is triggered;
• If the spring fell apart almost completely, it is replaced;
• когда пружина выйдет из крючка, установите его на место, согнув перед собой антенну (на фотографиях показан процесс установки);

• By inserting the spring plate into the groove, carefully tighten it.

To change the spring, the work should be done carefully and carefully: it can accidentally explode under the influence of the force caused by its. Even if the video is carefully removed, the spring tape breaks very quickly from the coil and can injure the hand with sharp edges.

Immediate replacement of the spring plate does not always work. This often slips, so attempts should be repeated to achieve the desired result.

Starter builder

The assembly of the starting installation is carried out in several stages:

• The coil turns over, installing it so that the bend of the spring accurately enters the groove of the case, as in the photo below;

• make two goals between which the spring is located;
• Put a cup for a mustache in place;
• Tighten the screw (photo below).

Make the above manipulations to put two goals. Failure to fulfill this requirement can lead to damage to a plastic glass over time, and when it is removed, it will begin to jam. Because of this, it seems that spring has come. To eliminate this drawback, you need to install this longer piece or additional washer.

When such details are absent, there is only a little unscrew the screw, and the starter assembly will begin to work without fixing. But this option is temporary. It is better to repair it as quickly as possible.

Spring tension

After installing the spring, tighten it. To do this, follow the following actions:

• Remove the handle from the starter cord;
• Then the rope is inserted into the groove of the coil;
• The spring is tightened by the rotation of the turn counterclockwise (winding);
• perform the required number of revolutions specified in the instructions for the operating of the used trimmer model for grass and the length of the cord used;
• At the very end, the rope descends into the hole in the starter cover;
• Place the handle in place by blocking it with a node.

If after the repair the spring continues to fly, you can get rid of this in the following ways:

• Insert the corresponding piece of the plate into the groove at the location of the spring hook;
• Drill holes on both sides of the groove in the coil to insert the spring hook and fix it with wire.

Replacing a torn cord

The broken rope is replaced in the following order:

• The old cord is removed;
• choose a rope of the desired size (thickness and length);
• Having passed it through a special hole in the coil, tie a knot;
• inflate the spring, making the required number of revolutions;
• Fix the pen

It is better to tighten the spring plate with your Partner so that the edge of the cord does not bend inside the starter mechanism.

Assemble a starter for a trimmer for grass and tighten the spring is easy, only you need to do this carefully and carefully. For different models of gasoline brushes, the launching mechanisms are the same, so they are repaired in the same way. There are some nuances associated with their constructive features.

Assembly of a motorcycle starter

During maintenance and repair of the starter, it is important to properly collect it. as if the assembly of the device was made by the manufacturer

Any incorrectly installed details will not allow you to fully use a trimmer for grass or braid.

• After winding the spring, turn the coil and install it so that the second spring hook will return to its place. There are technological windows on the coil to control the correct installation of the spring.
• Place the starter’s pulley and make sure that one of the spring hooks enters the groove located on the starter cover.
• Insert a spring and washers on the sides so that the spring does not wash the plastic compartment in which it is located. If the spring is broken and the other is not, an additional washer is put in its place.
• Insert a cup of antennae into the deepening of the coil.
• Put the coil in place, tighten the bolt to the end, but without fanaticism.

If you do not protect the compartment with washers from the main spring, the compartment where it moves when unscrewing and unscrewing the starter cord, the coil often snaps when trying to launch a gasoline trimmer for grass or a bush. The weakening of the coil bolt will lead to its loss.

Information on how to assemble a starter for a trimmer for grass, watch in the video.

The device of the chainsaw starter

Almost all leading manufacturers of chainsaws complete their products with starters of a similar principle of action. It is no coincidence that specialized stores offer universal designs of starters that are equally successful for both Stihl, Husqvarna, Makita chainsaws, and for Chinese semi.official fakes under the named brands. Only starters of domestic production (forester, Urals and a number of others) have some features only.

The principle of operation of the starter for the chainsaw is as follows. A handle is installed in the groove of the case, through which the cable is missed. If the handle is sharply lifted, the cable is stretched, and introduces the drum of a ratchet that transfers the movement to the drum with the slots provided for the shaft. In this case, the crankshaft makes several revolutions, and the working mixture in the space between the piston and the cylinder head is compressed. Accordingly, when lowering the handle, the contact between the ratchet and the slots is lost, and the shaft stops.

With an increase in the volume of the engine, the required amount of fuel-air mixture required for its subsequent ignition is also growing, so the number of jerks for the starting cable for large power saws increases. Therefore, in order to accelerate the return of the drum, baked return springs made of steels with high elastic properties are used.

The relief of the launch of the chainsaw is realized in the following ways:

• Preliminary enrichment of the working mixture, for which there is a special damper in the design of the carburetor.
• By installing an automatic decompression valve, which provides a decrease in the working pressure in the chainsaw cylinder.
• By installing an additional spring, which during the movement of the cable facilitates the spinning of the crankshaft.
• The presence in the design of some chainsaws (for example, Partner S, Maxcut, etc.) the primer. the pump that provides preliminary pumping of the fuel.

How to pull the spring

Spring repair

If the material of the starter spring is poor.quality, the spring bursts (usually at the place of its connection to the drum, where it forms a loop). Replace the spring in this case is not worth. Carefully clean its surface from dirt and traces of lubrication, gently polish the destruction place, and then release the spring at 600 650 ° C (the spring steel should purchase raspberry color). It is necessary to cool the spring slowly, and at 100 150ºС you can already carefully wrap its end in the shape of a restrictive protrusion on the inner surface of the drum (steel will acquire the necessary plasticity) and insert into place. Simple repair of the starter of the chainsaw of Repair Starter Chainsaw how to pull the chain on. The elastic properties of the spring will not change.

Tightening the spring PIM

The spring is pulled with a canvas worn on the drum. The tension and configuration of PIMs are made according to the following algorithm:

• Traction springs are put on the canvas (they are included);
• The spring mechanism is pulled (the number of revolutions depends on the diameter of the shaft and the mass.body characteristics of the canvas. you can find out the approximate number of revolutions from a special table);
• The spring is fixed with special brackets;
• traction springs are refueled in a shaft in special slots located at its ends;
• The lock of the spring is removed;
• The smoothness and speed of the canvas is checked (it is necessary to hold it with your hand to exclude sharp blows of the stoppers on the lower lamella on the edge of the box and, if the stoppers have not yet been installed, avoid complete winding of the canvas on the shaft).

Practical recommendations

In order to compare holes for fixing the cord in the pulley and the case, you may have to make a few more turns. A new rope is threaded into a technological hole and make a loop or knot: this will allow it to slip out of the pulley. The rope is taken to the side so that it does not interfere with further work. Next, it is necessary to fix the pulley.

First you need to install a smooth launch spring in place. It can be used the same if damage is not detected in it. or new replacement if necessary. A starter clamp is installed on top of the spring, which is fixed with a special screw. In the article we will tell you how to adjust how to adjust the carburetor on a video chainsaw. He reliably fixes the clamp for a long time, avoiding its distort and swing. I have a carburetor mounting stilettos on a chainsaw, how to change it? After that, you need to make a few turns of the rope and start it inside. The cover with the assembled starter is installed in place. With the help of screws, it is fixed.

After the repair and assembly is completed, you can start work. Self.repair of the starter does not take much time and does not require complex skills, but saves time and money if you perform such work in the service center.

It is necessary to approach the repair of the chainsaws responsibly and timely to carry out preventive examinations, monitor the quality of the fuel and oil used. These simple manipulations will increase the duration of the tool in working condition.

Spring repair

The procedure for repairing the start of the launch system:

• Dismantle the starter from the tool.
• Remove the protective cover.
• Wind the cord from the end of the pulley to avoid scrolling the mechanism.
• Pass the second end of the cord in the hole of the protective cover.
• Pull the cord 17-20 cm to check the turn of the pulley of the spring mechanism.
• Check the operation of the spring after stretching and releasing the mechanism.
• Unscrew the circle circle from the side of the generator, removing 3 fasteners.
• Demolish the pulley and cord.
• Check the condition of the parts for wear and the presence of damage and cliffs. If the cliff is small, then you can eliminate the defect by welding.

How to install a starter on a trimmer for grass

One of the key parts of the Kustorez is a starter designed to facilitate the start of the device engine. Like other parts, it breaks periodically. In this case, there are two solutions to the problem: to repair a trimmer for the starter’s grass or replace it completely. The second option is simpler, but more expensive. In addition, on sale you must first find the necessary part, since different models of lawn mowers use different starters. If you have free time and a screwdriver with an appropriate tip, you can restore the performance of this device, if you know how it works, what defects are characteristic of it and how to fix it. All this is in this material.

Three.dimensional starter. device and principle of operation

In order to independently fix the gasoline starter, you need to understand the principle of its operation and know its device. To date, trimmers for grass have manual and automatic starters, and the first. the most common.

Part is a plastic case in which a pulley with a cord wound on it is placed to start the engine. In order for the cord to be wound independently after winding the tool, the steel belt is located inside the pulley. A rattle is installed on the front of the pulley, which blocks the starter on the drive shaft of the tool motor.

The note! Depending on the model and brand from which a trimmer for grass is made (Huter, Husqvarna and other brands), the ratchet can consist of one or two separate components.

The principle of the manual starter is the same for Chinese, European and domestic manufacturers of gas trimmers, whether it be Hitachi, Patriot or another manufacturer. To start the engine, the owner of the device abruptly pulls by the cord. The pulley rotates from this movement, and the protrusions located on it enter into the hook with dogs located on the flywheel. Then the flywheel and crankshaft begin to rotate the pulley. After starting the engine under the influence of the centrifugal force, the crests and dogs diverge in different directions. And after the user releases it, the starter cord is wound on the pulley using a return spring.

Important! With intensive use of the drive cord, it breaks over time, and the spring wears out. These details are easy to replace with your own hands

Signs and reasons for the failure of the starter

In rare cases, the executive mechanism breaks when the tool is inaccurate. The consequences can be unpleasant: the deformed cord is wound on the flywheel of a working engine, a pulmonary pulley and a spring break. But these are isolated cases, a complete replacement of the starter is rarely required.

Diagnostics and elimination of malfunctions

To diagnose the starter mechanism for the purpose of its further repair, it is necessary to disassemble the assembly. It’s not difficult to do, just a screwdriver is needed. But during this operation you need to be careful. With careless movements, the spring can fly and harm the user.

How to repair a starter on a trimmer

One of the key nodes of the lawn mower is a starter designed to simplify the start of the device engine. Like other details, it breaks periodically. In this case, there are two solutions to the problem: repair of the starter of the trimmer for grass or its complete replacement. The second option is simpler, but expensive. In addition, the required detail first needs to be found on sale, since different starters are used for different models of gasoline. In the presence of free time and screwdriver with a suitable tip, restore the performance of this node yourself, if you know how it works, what malfunctions are characteristic of it, and how to eliminate them correctly. About all this. in this material.

A torn rope is replaced in the following sequence:

• The old cord is removed;
• choose a suitable rope (thickness and length);
• Having reached it through a special hole in the coil, a knot is tied;
• Sprinkle a spring, producing the required number of revolutions;
• Fix the pen.

It is better to stretch the spring plate along with the partner so that the edge of the cord does not hit the starter mechanism.

It is easy to assemble a starter on a trimmer and wound a spring, only you should do it carefully and with caution. For different models, the gas tanks of the launching mechanisms are the same, so they are repaired in a similar way. In this case, there are some nuances associated with their constructive features.

Trimmer starter. device and principle of operation

In order to fix the starter of the lawn mower on your own, you need to understand the principle of its work and know its device. Today, manual and automatic starters are installed on trimmers, while the former are most often found.

The part is a plastic case in which a pulley with a cord wound on it is placed to start the engine. So that the lace is independently twisted after the tool factory, on the inside of the pulley there is a strip spring made of alloy steel. On the front of the pulley, a ratchet is installed that creates a starter‘s engagement with a drive engine shaft of the tool.

On a note! Depending on the model and the brand that released a trimmer for grass (Huter, Husqvarna and other brands), a pulley with a ratchet can be a single whole or two separate components.

The principle of the manual starter is the same on the gas troops of Chinese, European and domestic production, whether it be Hitachi, Patriot or another manufacturer. To start the engine, the owner of the device abruptly pulls the cord. The pulley turns from this movement, and the ledges located on it are hooked with dogs located on the flywheel. Further with the pulley, the flywheel and the crankshaft begins to rotate. After starting the engine under the influence of centrifugal force, the protrusions and dogs diverge in different directions. And the starter cord after the user releases it, wound on the pulley using a return spring.

Important! With intensive use of the drive cord, it breaks off over time, and the strip spring wear out. These details are easy to replace with your own hands.

Motobobok ignition system

Ignition adjustment

The ignition coil for the Neva walk.behind tract is adjusted as follows by the ignition adjustment overview of the motor block engine

One of the main factors of the correct operation of the ignition system plays a gap between the starter and the flywheel. It should be in the range from 0.1 to 0.15 mm.

To adjust it on the Neva walk.behind tractor, it is necessary to remove the housing and unscrew the stator bolts. Then put the probe and set the necessary gap, tighten the bolts back and check the gap over the entire surface of the flywheel.

Generator, malfunctions, elimination

The generator is an important component of the entire mechanism. It is designed to charge the battery and work headlights

When choosing a generator, you need to pay attention to its power. It should exceed the power of all connected devices to ensure uninterrupted operation

For the Neva walk.behind tractor, it is possible to use an old car generator.

Important! During its installation, it is necessary to observe the scheme presented below. Otherwise, the generator is possible

There are 4 wires in the generator. Two of which are blue. It is thanks to them that the converter is connected. Red, connects to the headlights, and gives tension on them.

Electrostarter

Many people seek to improve their walk.behind tract. In the winter seasons, he does not start poorly due to the fact that the manual starter does not scroll. In solving this problem for the walk.behind tractor, Neva came up with a special electric starter. This is an autonomous device that, when the ignition is turned on, begins to rotate and gives a spark.

Elektrostarter is a complex design, and it is not realistic to make it at home. You can use any other automobile electric starter that could stay from the old car.

Candles

What candles are needed for, and how to change them we have already figured out. Let’s look at the brands that are necessary for each specific type of Neva engine:

In standard configuration, Neva Motobobes are not equipped with a headlight. However, this option is presented as an additional. Since work in the evening is almost impossible without headlights.

If desired, you can install the headlights yourself from the car, scooter, tractor, etc.D. To do this, with the help of welding, make a special box for the headlight and get it there. And attach the wires from it to the generator. But not directly, but through a switch that should be in the middle and be responsible for turning on and off the headlights.

How to make a repair starter with your own hands

If there are difficulties during the launch of the tool, power disappeared or malfunctions arose in the fuel supply system, then it is necessary to repair the chainsaw starter with your own hands or give the tool to the service.

Diagnostics

Diagnosis of the tool launch system is carried out as follows:

• Unscrew the fasteners and remove the lid.
• Turn a screw that attaches the mechanism to the protective cover.
• The starter smoothly launch, removing the spring and clamps from it.
• For examination for wear and defects, a reel with a cable is dismantled.
• Check the fuel system for water in it. If there is water inside the system, then the fuel fluid must be replaced.
• Conduct an inspection of the power unit for overflow with fuel fluid. In this case, you need to unscrew and dry the spark plug, pull the starter, dismantling the air damper.
• Check the spark of spark.

How to wind a rope on a trimmer starter for Patriot grass

Chainsaw is an indispensable assistant in the construction and harvesting of firewood. Correct work with moderate use guarantees a long service life without breakdowns. However, the problem may arise quite unexpectedly, and the working chainsaw loses its effectiveness, and the malfunction can be a trifle.

The repair of the starter’s chainsaw is presented after a starter’s break to break. Without a chainsaw cord, it becomes completely inoperative; There is no other way to launch a tool. Repair was carried out using the Partner P350S chainsaw; The cunning reliable launch of this saw requires a minimum stretch of the launch cord 4-5 times to work, therefore, probably, the first fault was a breakdown of the cord. The cord does not break immediately, initially the thread of the protective stocking of the cord breaks off and prevents the launch of the saw. It is better not to wait until all the threads are torn and fix the cord in advance. No need to invent anything, the repair should not create difficulties, but accurate compliance with the assembly conditions is necessary. The step.by.step guide for shooting photos and video scheme is the following.

Turn the three screws with which the starter cover is attached. For this process, a straight wrench with a straight screwdriver is suitable, but to speed up work it is better to use a standard tool.

Remove the starter. The chainsaw is equipped with a smooth start mechanism located above the coil with a cord.

Turn the screw that is attached to the smooth starter and the starter coil is attached. Be careful not to lose the puck!

The starter is removed. Remove the screw. Remove the screw.

Melt the ends of the rope above the fire so that it does not dissolve.

Tied a complex knot on one end. Installation should be large diameter, but should not act when installing on the reel.

Insert the cord into the coil hole. Do not twist the cord!

Replace the coil. Installation error may occur here. The coil has two grooves, one of which should fall a spiral spring hook. Set the coil so that it clicks in place, and the hook snaps in place. This is checked by rotation of the coil clockwise to determine the occurrence of a return force.

The cord node is fixed by a spring protrusion

Install a smooth start device. The protrusion of the mechanism should be in the deepening of the coil.

Insert the other end of the cord into the outlet.

Installation of a smooth start device screw is screwed. The cord is stretched

Insert the cord into the starting handle. Tie a large node at the end of the rope. With the help of a small node, it is likely that the rope will slip, and the entire cord will be wrapped in a starter, and to pull it, you will need to remove the starter again. Check the reliability of the node. Look at the photo.

Cord in the descent handle lock assembly

The most important point! We release the cord loop inside the starter and begin to rotate the starting mechanism clockwise without wrapping the cord! This saw requires at least five revolutions. We manually block the coil. Pull the loop handle. Holding the cord and mechanism, we allow you to wind the cord to the reel. Watch the video.

Replace the starter and fix it with three screws. Repair is made.

Repair of a damaged or damaged cord with step.by.step instructions takes 15 minutes, which is much faster and cheaper than contacting the service center.

How to fix a starter on a chainsaw

The reason for the malfunction of the launch system of the chainsaw may be:

• Drive pulley. This part is subjected to high axial and radial loads, therefore, before starting work, it is recommended to inspect the pulley for damage and cracks on the back of the case. If necessary, repair the part or replace it with a new.
• Spring mechanism. If he has lost his properties or there are cracks or breakthroughs on it, it is necessary to replace this element. It is also recommended to inspect the places for the presence of defects.
• The rope of the launch system. The rope should be examined for wear and injuries. If necessary, replace the part and install it with the pulley.

Diagnostics

Diagnosis of the tool launch system is carried out as follows:

• Unscrew the fasteners and remove the lid.
• Turn a screw that attaches the mechanism to the protective cover.
• The starter smoothly launch, removing the spring and clamps from it.
• For examination for wear and defects, a reel with a cable is dismantled.
• Check the fuel system for water in it. If there is water inside the system, then the fuel fluid must be replaced.
• Conduct an inspection of the power unit for overflow with fuel fluid. In this case, you need to unscrew and dry the spark plug, pull the starter, dismantling the air damper.
• Check the spark of spark.

Replacement of the cord

In order to replace the cord, the following tools will be required:

Replacing the launch cord is as follows:

• You need to unscrew the fasteners that hold the side cover with a screwdriver.
• Then dismantle the starter from the tool body.
• After that, you need to turn the lid and conduct an inspection.
• Then dismantle the clip and spring.
• Untie the knot on the rope.
• You need to pull out the pulley on which the cord is wound. Remove the cord and replace it with a new.
• Then get the pulley in place and tie the rope on the knot. Set the clip and spring.
• After that, tighten the lid using fasteners.
• At the end, install the starter in place and fasten the fasteners.

Spring repair

The procedure for repairing the start of the launch system:

• Dismantle the starter from the tool.
• Remove the protective cover.
• Wind the cord from the end of the pulley to avoid scrolling the mechanism.
• Pass the second end of the cord in the hole of the protective cover.
• Pull the cord 17-20 cm to check the turn of the pulley of the spring mechanism.
• Check the operation of the spring after stretching and releasing the mechanism.
• Unscrew the circle circle from the side of the generator, removing 3 fasteners.
• Demolish the pulley and cord.
• Check the condition of the parts for wear and the presence of damage and cliffs. If the cliff is small, then you can eliminate the defect by welding.

How to put a spring

In order to install a new spring, the following actions must be performed:

• Gently extract the clip of mechanism.
• Conduct an inspection of the inner part of the clip in which the spring mechanism is located near the C-shaped element.
• Fix and pull the upper part of the spring with your finger and pull the launch mechanism to the side.
• Extract a worn.out mechanism and wind a new spring. Excesses and twisting of the element should be avoided.
• Collect a new spring mechanism. It is recommended to do this slowly so that the mechanism does not unwind.
• Twine the spring and insert it into the starter mechanism.
• Gently fix the clip.

Prevention of problems

At some point, difficulties with the starter appear on any trimmer

So, finding that the starter mechanism broke on the gas station, one should not rush to the specialists to do it immediately. Knowing how the malfunction is eliminated and/or the details are replaced, repair work can be performed without the help of others. This does not require any specific tool. At first, the procedure may seem complex and painful, but countless webs dedicated to the repair of the starter will help to solve the case very rapidly and simply.

For a lawn mower or a gasoline trimmer for grass. a mechanical node, in which a pulley puts on a ratchet enters. The pulley in the initial position is wound a rope. At starting, it stretches outward. The pulley is spring.loaded. it is worth releasing the end of the rope for you, how it drowns back. As a spring, a flat ribbon shared in a ring is used. She recalls the spring in huge mechanical watches that start a day. The starter itself is placed more often on the back than closer to the front end of a mowing or a trimmer for grass. To correctly create all manipulations with a starter for a lawn mower, you should know the features of the device and installation.

Repair of the starter of the chainsaw Patriot

Chainsaw is an indispensable tool not only for a summer resident, but also during construction work. If you need to stock up on firewood for the winter, then going to the forest without a chainsaw does not make sense at all. With the proper operation of the tool, it can last a long time, but in any case, sooner or later various types of malfunctions will occur. One of such malfunctions is the starter breakdown, as a result of which the engine starts to start. In this situation, it is advisable to repair the starter of the chainsaw starter with your own hands. How to do this, we will find out in the material.

Typical breakdowns and repair of the chainsaw starter

Before carrying out repairs, it is necessary to find out the reasons for the breakdown. Since the product is constantly subjected to dynamic and other types of loads, its failure is not excluded. Frequent causes of starter breakdowns are: rupture of the cable, abrasion or painting several shits of the rattle drum, damage to the spring, a crack of the pulley and others. To determine why the saw does not start, you will need to conduct an appropriate revision of the starting mechanism. Consider the main types of malfunctions, and also find out how to properly repair the product.

https: // hitech-online.ru/Tehnika-Dlya-Sada/Trimmer/Remont-STARTERA.html https: // Chistayrabota.ru/kak-razobrat-trimmer-patriot/https: // StrPort.ru/instrumenty/Trimmer-Benzinovi-Patriot-PT-3355-SOSOBENNOSTI-KHARAKTERICTIKI-InSTRUKIYA-OTZYVY HTTPS: // StrPort.RU/Instrumenty/Benzinovyi-Trimmer-Patriot-PT-3055-%E2%80%93-SOSOBENNOSTI-KHARAKI-INSTRUKTSIYA-OTZYVY HTTPS: // CRAST.ru/Instrumenty/Remontra-Benzopily-Patriot

Prevention of problems

Sooner or later, problems with the starter arise on any trimmer. STIHL FS 55, MTD 790 or other brand. This malfunction can be postponed, but the tool should be treated carefully. In particular, do not make too sharp jerks, it will break the cord or spring. It is not recommended to expose a brush to impacts or other physical influences. In the case of a breakdown of the starter case and the cut of the cord, it can be wound on the engine flywheel. It will break the pulley and break the spring.

Therefore, having discovered that the executive mechanism has broken on the uterus, do not immediately rush with the help of specialists. Knowing how to eliminate problems and / or replace the details, you can carry out repair work yourself. This does not require a special tool. At first, the procedure may seem tedious and tiring, but numerous online repair videos when starting can help you solve the problem as quickly as possible and easier.