How to make light on a walk-behind tractor without a generator
Front lamp made of scrap materials
To make a bright lantern for a bicycle with your own hands, first of all, let’s decide on the LED. In our case, the heart of the circuit will be a 10W CREE XM-L. Its light output of 1000 lm is enough not only to illuminate the roadway, but also to surprise the drivers of oncoming traffic. To form a narrow beam, you need a small lens and a mount for it.
As a retainer, you can use a flange from a P213 transistor and a part of a plastic tube from a coil. The basis for the flashlight is a radiator from a computer processor, in which you need to drill two holes for attaching the LED, two for the wires and two for attaching the focusing lens. First, we fix the LED, not forgetting to apply thermal paste. Then we pass the wires through the holes and solder to the plus and minus CREE XM-L. The next step is to assemble the focusing part. You may need to experiment with the focal length and shorten the tube length a little. Next is the case. You can take spare parts from an old bicycle headlight, or you can make it yourself from foil PCB. The dimensions of the case are selected individually, depending on the shape of the radiator. This design provides a place for the driver (you can see its diagram in this article) and a microswitch located behind the radiator. The front of the lens is protected by plexiglass, which is held by 4 screws (it would be more efficient and ergonomic to fix it with hot melt glue). We paint the body black and the front light on the CREE XM-L LED is ready to be mounted on a bicycle. It remains to stock up on two lithium batteries and you can hit the road.
We make light on a walk-behind tractor without a generator: instructions and diagram
For heavy motoblocks
In heavy walk-behind tractors, generators and belt transmission are not used, therefore, rechargeable batteries are used for the light source.
It is recommended to install batteries from motorcycles, since they have sufficient power, small dimensions and weight.
The only drawback is that you need to make and fix the battery holder yourself. For this, an iron profile or corners welded into a single structure are suitable. And for greater reliability, the product is treated with a soft material, after which the battery is attached.
For motoblocks with a belt drive
A feature of technology with a belt drive is the absence of a generator. Therefore, the owner of the special equipment must independently install the electrical equipment with the help of locksmith tools and additional spare parts. They can be removed from a car or other equipment.
The main thing during installation is to replace the generator pulley with one that corresponds to the belt drive of the walk-behind tractor. For greater convenience, the electrical equipment is attached at the back, after which its performance is checked and the lighting is connected.
The absence of a generator is a feature of the belt drive technology.
Bike mount
We figured out how to make a flashlight for a bicycle, now you need to attach it to your vehicle. The easiest way to do this is with a conventional plastic clamp. Drill the body of your device on both sides closer to the back wall, best of all, where there is a distance between the heatsink and the back wall. Insert a plastic strap through the hole and tighten it to a convenient location on the handlebars of your bike.
Done! You have made a bicycle flashlight with your own hands. It’s time to test it thoroughly in the evening driving conditions. Remember to bring your regular flashlight with you in case something goes wrong and your new bike flashlight needs work. Good luck on the road!
Homemade taillight from an old reflector
Assembling a tail light on a bicycle with your own hands is also easy. We will take as a basis an ordinary reflector in a plastic case, which is an integral part of any bicycle. In addition to him, we need:
The second method involves the installation of a more powerful radiator with fins that improve heat dissipation. Any radiator removed from Soviet equipment or from the processor of an old computer is perfect.
We cut it to the required size, try on and drill two holes for attaching the LED. Then we drill 4 holes in a plastic case with a diameter of 4.5 mm for screeds.
Nylon ties should not be the thinnest, for example, 4 mm by 160 mm, with which we firmly tighten the radiator with the reflector body.
The made lantern is completely sealed, which is both good and bad. On the one hand, such a taillight is completely protected from all weather conditions. On the other hand, the PCB and plastic housing hinders the cooling of the LED.
To reduce heat loss on the LED, a homemade taillight can be improved in several ways:
- connect the LED to an adjustable driver, setting the half power mode;
- use a radiator of a different form factor to avoid complete isolation;
- install some super bright red LEDs like smd 3014.
Let’s start assembling
Let’s figure out further how to make a lantern for a bicycle with our own hands. First, we fix the lens in the front of the case with hot melt glue. Hot melt glue is the most reliable option, but if one is not available, a good superglue can be used, subsequently sealing the remaining gaps with a sealant.
Attached bicycle light on the handlebars
Install the LED at some distance from the lens, having previously fixed it to the radiator. You will need to drill holes in the radiator to remove the wires. At this stage, you need to power the device and find out what distance will be optimal. Try your flashlight in a dark room, directing a beam of light onto the wall. this way you can most clearly evaluate the result.
Fix the radiator in place. Depending on which case you managed to find, choose a mounting method. Perhaps the hot melt glue will not be enough, then you will have to drill holes on the sides and fix the radiator with screws.
Now you need to install the back cover of your flashlight. If it is not provided in the case, you can cut it out of a piece of plastic. There must be a distance between the radiator and the cover. Fasten the batteries on the inside of the cover, and on the outside. the switch, connecting it according to the installation diagram of your LED. Place the cover on the housing. Best of all, if the cover is secured with screws, then it can be removed to replace the batteries.
How can you make light on a walk-behind tractor?
How to make light on a walk-behind tractor, because most models are not equipped with headlights? a uniaxial tractor (mini-tractor) is a mechanism that is designed for agricultural work (plowing, cultivation, watering, etc.). Many models can be used as a vehicle by means of trailers. In this form, walk-behind tractors transport people and goods, which makes harvesting easier.
Unit electrical system
Medium and heavy motoblocks are equipped with an electric generator that charges the battery and powers the headlight. The main function of the battery is to start the engine of the mini-tractor using an electric starter. On medium and heavy walk-behind tractors, it is possible to connect several headlights (main and rear for the trailer), direction indicators.
The power of the working generator is sufficient for the installation of additional electrical equipment, as well as the stable simultaneous operation of all electrical devices of the walk-behind tractor. Manufacturing plants have provided for the possibility of additional installation of electrical equipment and equip mini-tractors with generators with a power reserve of about 30%.
The battery capacity corresponds to the starting current of the electric starter. Most mini-tractor models are equipped with generators without electrical excitation. It will be replaced by constantly rotating magnets. Most often, manufacturers install single-phase generators that produce alternating current.
Self-installation of the headlight
If the unit was purchased without a lighting system, then you should not be upset. You can install it yourself. Some manufacturers sell separately the lighting kit (headlight, wires and switch), earning extra money from this option, realizing that most owners will use a single axle tractor as a vehicle. The engine has a special place for connecting the factory headlight. It would seem that this is a little money in comparison with the price of a mini-tractor, but why spend it if the lighting can be made from improvised means?
Let’s consider in detail how to connect the headlight to the walk-behind tractor. The first step is to find the lighting element itself. Almost every owner of the unit has another mechanical device (car, moped, scooter, tractor), to which additional headlights are attached. If this is not the case, then a used headlight can be purchased at disassembly points or in the automotive market to save money. If possible, it is best to purchase a new headlight that can be matched to the color of your mini tractor. A headlight for a small motorcycle or scooter is suitable for this.
Generator 220 volts from a walk-behind tractor // No secrets!!!
It is necessary to purchase both a toggle switch and the required length of electrical wire.
The most convenient place to install the toggle switch (switch) of the headlight is the steering column near the gear lever.
We install and fix the switch. Next, we move on to installing the headlight. Find a place that’s comfortable for her. The front of the engine or steering column is best suited for installing this equipment. Experts advise to mount the headlight on the steering column tube, because the one placed on the engine will get dirty when driving in the rain. Next, we stretch the wires. If the walk-behind tractor has a place for connecting the factory headlight, then we connect the wires to it, if it is absent, then it is most convenient to draw the power from the terminal of the oil pressure indicator lamp. Next, we connect the wires to the switch, and from it we pull the cord to the headlight, using the body of the walk-behind tractor as a mass. We fasten the wires with clamps or electrical tape to the steering column.
Connection by means of an electric generator
The best way to connect the light on the walk-behind tractor is to use the generator supplied with the machine. As a rule, standard electric generators for all models of this special equipment have excess power that can be used to operate the lighting fixture. The connection of the headlamp to the energy source is carried out according to the following algorithm:
- using wiring, the lighting element is connected to the generator;
- one of the wires is equipped with a toggle switch, which it is desirable to place at the steering wheel or in another place convenient for the driver;
- after checking the functionality, the electrical wiring is placed in a protective corrugation and fixed on the body of the mini-machine.
If the standard generator has sufficient power, then the lighting will be bright and stable. When, with an increase in the load on the device, the lamp starts blinking and turns off, it makes sense to think about replacing the standard electric generator with a device from any tractor model.
Caution! When using equipment designed for other equipment, it is necessary to provide the single-axle tractor with additional support frames, which increase the fastening strength.
Self-installation of the headlight
If the unit was purchased without a lighting system, then you should not be upset. You can install it yourself. Some manufacturers sell separately the lighting kit (headlight, wires and switch), earning extra money from this option, realizing that most owners will use a single axle tractor as a vehicle. The engine has a special place for connecting the factory headlight. It would seem that this is a little money in comparison with the price of a mini-tractor, but why spend it if the lighting can be made from improvised means?
Let’s consider in detail how to connect the headlight to the walk-behind tractor. The first step is to find the lighting element itself. Almost every owner of the unit has another mechanical device (car, moped, scooter, tractor), to which additional headlights are attached. If this is not the case, then a used headlight can be purchased at disassembly points or in the automotive market to save money. If possible, it is best to purchase a new headlight that can be matched to the color of your mini tractor. A headlight for a small motorcycle or scooter is suitable for this.
It is necessary to purchase both a toggle switch and the required length of electrical wire.
The most convenient place to install the toggle switch (switch) of the headlight is the steering column near the gear lever.
We install and fix the switch. Next, we move on to installing the headlight. Find a place that’s comfortable for her. The front of the engine or steering column is best suited for installing this equipment. Experts advise to mount the headlight on the steering column tube, because the one placed on the engine will get dirty when driving in the rain. Next, we stretch the wires. If the walk-behind tractor has a place for connecting the factory headlight, then we connect the wires to it, if it is absent, then it is most convenient to draw the power from the terminal of the oil pressure indicator lamp. Next, we connect the wires to the switch, and from it we pull the cord to the headlight, using the body of the walk-behind tractor as a mass. We fasten the wires with clamps or electrical tape to the steering column.
How to make light on a walk-behind tractor?
Many manufacturers produce this agricultural mechanism without built-in lighting. Here the question arises of how to connect the headlight to a single-axle tractor yourself with your own hands.
Unit electrical system
Medium and heavy motoblocks are equipped with an electric generator that charges the battery and powers the headlight. The main function of the battery is to start the engine of the mini-tractor using an electric starter. On medium and heavy walk-behind tractors, it is possible to connect several headlights (main and rear for the trailer), direction indicators.
The power of the working generator is sufficient for the installation of additional electrical equipment, as well as the stable simultaneous operation of all electrical devices of the walk-behind tractor. Manufacturing plants have provided for the possibility of additional installation of electrical equipment and equip mini-tractors with generators with a power reserve of about 30%.
The battery capacity corresponds to the starting current of the electric starter. Most mini-tractor models are equipped with generators without electrical excitation. It will be replaced by constantly rotating magnets. Most often, manufacturers install single-phase generators that produce alternating current.
Work of light from the ignition system
You can install the light on a mini-tractor without a battery and an electric generator, using the most affordable way. connecting from the ignition. For the headlamp to work, one end of the electrical wire is fed to the starting system, and the other goes through the switch to the lantern. The disadvantage of the light of the walk-behind tractor from the ignition coil is the impossibility of lighting when the engine is off.
Each of the methods of connecting lighting devices listed in the article is suitable for various models of special equipment, both domestic and foreign.
Helpful information
a uniaxial tractor is a universal agricultural mechanism that is used to perform various tasks on personal plots, dachas and vegetable gardens. The versatility of the device allows you to use it both for land work and for transporting crops and other goods. Unfortunately, the complete set of many mini-tractor models does not provide for the presence of lighting elements. Therefore, the question of how to make light on a walk-behind tractor is relevant for most owners of this compact and practical machine.
DIY lighting installation
Manufacturers of special equipment offer spare parts for walk-behind tractors and ready-to-connect lighting kits, consisting of a headlight, a toggle switch and wiring. However, many owners of units, to avoid additional costs, prefer independent preparation and installation of lighting equipment. Installing lighting on a mini-tractor with your own hands does not require special skills, the acquisition of expensive materials and the use of special equipment. Headlights from various Soviet-assembled vehicles are often used as a lighting device for agricultural machines.
Note! The brightness of the old flashlight may not be enough for the departure of special equipment on the track or for performing a large amount of work. In addition, the service life of such a device does not exceed 2-3 months.
Headlight for walk-behind tractor. independent production
Many owners of motoblocks use headlights from domestic and imported cars to install on their units. This method is the simplest, however, it should be remembered that the old headlight on a single-axle tractor will not emit bright enough light and will last no more than several months.
It is much better to make your own lighting for an agricultural machine. This does not require the purchase of expensive materials and equipment. You will need the same old headlight, the filling of which you will later replace with new parts. The order of work is as follows:
- Remove the existing glass surface and other elements from the old headlight that are attached to the base with plastic clips;
- Next, make a plaster cast based on the headlight frame. To this end, pour the still liquid material into the headlight base along its entire perimeter. After the final drying of the plaster mass, it must be carefully removed;
- Apply 3 layers of fiberglass to the impression. There should be a layer of epoxy between each of the tiers. Place the workpiece in a vacuum and wait at least a day. during this time the impression will completely solidify. After that, align the workpiece so that even the slightest chips do not remain on it;
- Start making glass for your homemade headlight. To do this, preheat the oven to 190 ° C, make a stand of 8 battens fastened together and fix a glass fabric sheet in it. Before putting the mold in the oven, do not forget to remove the protective film from the material, otherwise it will be covered with dust particles;
- As soon as the material sags in the stand, remove it from the oven and apply to the previously made workpiece. The product must be placed and kept under full vacuum until it hardens.
After hardening, the manufactured headlamp will need to be carefully sanded, degreased and dried. Further, 1-2 halogen lamps or LED strip are placed inside it. Installing the headlamp on a single axle tractor is done after a thorough inspection of the lighting fixture. To fit the headlamp on a single axle tractor, be sure to use a sturdy frame and at least 4 fasteners.
For heavy motoblocks
In heavy walk-behind tractors, generators and belt transmission are not used, therefore, rechargeable batteries are used for the light source.
It is recommended to install batteries from motorcycles, since they have sufficient power, small dimensions and weight.
The only drawback is that you need to make and fix the battery holder yourself. For this, an iron profile or corners welded into a single structure are suitable. And for greater reliability, the product is treated with a soft material, after which the battery is attached.
Electrical diagram
The headlight connection diagram is quite simple and consists of only three main elements:
- a power source, including an ignition, generator or battery;
- power switch. a simple button that breaks and turns on the power supply circuit for the lamp;
- lamp holder to which wires are connected from a power source through a switch.
A fairly simple diagram for connecting a headlight to a uniaxial tractor
For greater reliability, all wires are placed in a special corrugation. The material protects the electrical wiring from damage and allows the equipment to be fixed in such a way that it does not interfere with the use of a single axle tractor.
Connecting and checking the headlight
The procedure for installing the light on the equipment does not take much time.
Basic steps on how to connect a headlight to a single axle tractor:
- install an external power source for the light;
- connect wires to electricity and headlight;
- add a switch to turn the light on and off;
- carry out the final assembly of the elements.
After that, they test lighting, the continuity of operation and reliability of the switch.
Specificity of selection and installation of lighting
Before installing the headlamp on a single-axle tractor, you need to decide on the equipment used. The choice of a lamp for lighting depends on the complexity and nature of the work being carried out, as well as the lighting requirements.
The more light is needed at night, the more power of the selected lamp should be.
Also, technical features arise when installing headlights. If the power of the generator is not enough to provide a constant flow of light, use 12 V batteries. It is recommended to use light equipment so as not to increase the load on a single-axle tractor.
From generator
Most manufacturers make walk-behind tractors with electric generators with sufficient power for the regular operation of equipment and connecting lighting. If the equipment is weak, you can replace the generator with a more suitable type.
Without a generator and battery, you can connect the lighting yourself
Step-by-step installation instructions:
- connect wires to the generator contacts, and one of them must be connected via a button;
- conduct wiring from the generator and switch to the lighting fixture and check the operation of the system;
- fix the headlamp to the frame and use protective elements to prevent moisture and damage.
You can independently connect the lighting without a generator and battery, but this will require a headlight with an independent power source.
Necessary tools for the job
Before starting work, it is necessary to prepare all materials, including wiring, headlight, corrugation, and also assemble a set of tools:
- soldering iron;
- screwdrivers and wrenches;
- nippers and stationery knife;
- electrical tape and heat shrink tubing;
- electric drill and fixing materials.
How to make a headlamp for a uniaxial tractor?
As a lighting on a uniaxial tractor, many owners of special equipment install headlights of domestic and foreign cars. This option is expensive and unreliable. There is not enough outgoing light, and the system itself will not last more than a few months. Alternatively, they develop a headlight for a uniaxial tractor with their own hands, which allows you to get the necessary lighting and equipment power.
Step-by-step instructions for making:
- Purchase an old, inexpensive headlight. Equipment from Soviet cars is suitable.
- Remove the glass protection and other elements fixed with plastic fasteners from the device.
- Pour the dummy headlight using plaster, for which the finished material is poured into the device and remains until completely dry. After that, you can remove the cast, preserving its integrity.
- The resulting template is applied in three layers of fiberglass, each time treating the material with epoxy resin. After processing, the future headlight must dry under vacuum.
Many owners install the headlights of domestic cars as lighting on a single-axle tractor.
Before using the headlight in a walk-behind tractor, it is necessary to check the device’s operability and the absence of short circuits several times in order to avoid breakdowns.
DIY headlight installation options
After making the headlight and preparing the tools, they proceed to installing the light on a single-axle tractor.
The choice of the source of electricity is one of the main tasks when installing the headlight yourself.
Step-by-step instructions for performing:
- Conduct wiring from the electricity source to the headlight, check the system performance and the brightness of the light.
- Install the switch in a convenient place for use, and then integrate it into the headlamp power circuit. Only one wire goes from the button to the light.
- At the final stage, they turn off the power supply and proceed to the installation of protective elements, corrugations, as well as fixing all the parts on the equipment. Without heat shrinkage and additional means, lighting can be damaged or fail.
One of the main tasks when installing a headlight yourself is choosing source of electricity. Usually use a generator, battery or ignition.
For heavy motoblocks
In heavy walk-behind tractors, generators and belt transmission are not used, therefore, rechargeable batteries are used for the light source.
It is recommended to install batteries from motorcycles, since they have sufficient power, small dimensions and weight.
The only drawback is that you need to make and fix the battery holder yourself. For this, an iron profile or corners welded into a single structure are suitable. And for greater reliability, the product is treated with a soft material, after which the battery is attached.
How to choose a generator for a walk-behind tractor?
It can be quite difficult for a novice farmer to choose the right generator for a walk-behind tractor. However, not everything is as complicated as it might seem at first glance.
The single most important factor to pay attention to is the power of the device. Whichever generator you choose for an agricultural machine, its power must necessarily exceed the total power of the loads under which the single-axle tractor operates. This will allow the device to work properly under a voltage of 220 Volts without the risk of surges in the electrical network, and power all electrical appliances available on the walk-behind tractor.
Often, inexperienced owners of walk-behind tractors purchase and equip their equipment with generators designed for installation on cars. This is the best option if the farm regularly uses a powerful single-axle tractor of a heavy class. In other cases, it is impractical to buy such generators due to their high cost.
Possible difficulties and ways to solve them
Although mounting a headlight on a single axle tractor is an easy task with a minimum number of elements, machine owners face challenges.
The main difficulties and methods of solution:
- the headlight does not light up: it is necessary to check the performance of the structure from a constant power source;
- the light does not turn on / off: the malfunction is associated with the button that is out of order, or the contacts are out of order;
- after installing the headlight on a single-axle tractor, nothing happens: the problem lies in the generator or the battery, and electrical wires may also be damaged.
How to make a headlamp for a uniaxial tractor?
As a lighting on a uniaxial tractor, many owners of special equipment install headlights of domestic and foreign cars. This option is expensive and unreliable. There is not enough outgoing light, and the system itself will not last more than a few months. Alternatively, they develop a headlight for a uniaxial tractor with their own hands, which allows you to get the necessary lighting and equipment power.
Step-by-step instructions for making:
- Purchase an old, inexpensive headlight. Equipment from Soviet cars is suitable.
- Remove the glass protection and other elements fixed with plastic fasteners from the device.
- Pour the dummy headlight using plaster, for which the finished material is poured into the device and remains until completely dry. After that, you can remove the cast, preserving its integrity.
- The resulting template is applied in three layers of fiberglass, each time treating the material with epoxy resin. After processing, the future headlight must dry under vacuum.
Many owners install the headlights of domestic cars as lighting on a single-axle tractor.
Before using the headlight in a walk-behind tractor, it is necessary to check the device’s operability and the absence of short circuits several times in order to avoid breakdowns.
Light without battery and generator
When deciding how to make a headlight for their walk-behind tractor, most make the most technically complex decisions. Light can be made simply, quickly and inexpensively using bicycle lights.
Bicycle lights have the following benefits:
- no need for wiring;
- minimum financial investments with high efficiency;
- reliability in all weather conditions;
- availability of its own charger for portable batteries;
- the ability to mount on the steering column on the brackets that come with the kit;
- quick removal for manual use or for charging.
It costs two bike lights to purchase. It is advisable to use one for the main beam, the second for lighting directly in front of the unit.
How to choose the right lighting coil
Often, when using Lifan engines in appliances and households, it becomes necessary to connect various electrical appliances. Many craftsmen are trying to use additional installed generators. But it is expensive and not always convenient. We have to come up with complex designs, adapt the pulley and belt systems. This greatly complicates the entire mechanism, and most importantly, the reliability of the entire system is lost. An excellent way out of this situation is the generator built into the engine (flywheel with magnets plus a lighting coil). Lifan offers its customers several options for such generators.
Lifan’s standard coil is a 0.6 Amp (12V) coil for a standard single cylinder motor and a 3 Amp (12V) coil for a standard twin cylinder motor. Due to the fact that their power is too low for connecting third-party consumers, such coils are sufficient only for starting the engine and its operation.
If you want to connect additional useful consumers to the engine (for example, lighting lamps, battery power, receiver, navigator, etc.), then for these purposes it is necessary to use more powerful coils.
In this case, the minimum power for a single-cylinder motor will be a 3 Ampere coil, through which you can connect a lamp up to 40 watts. Further, if you need more powerful consumers, then the coil will already be 5 Amperes or 7 Amps. You can also directly connect lamps to them, for example, halogen lamps, since the current is not too large, and a relay-regulator in this case is not necessary in the circuit. The total power of connected devices when using a 5 Ampere coil increases to 60 watts, a 7 ampere coil rises to 84 watts. (How to find the power “P” when we know the current strength “I” and the voltage “U” probably everyone well remembers from the school physics course. We just find the product of the current and voltage P = IхU). All of the above coils provide alternating voltage (AC). Thus, it is clear that lamps and devices need to be selected appropriately.
However, if it becomes necessary to charge the battery installed on the equipment, then you will already need a constant voltage (DC) at the output. The above coils alone will not be enough. Then you will additionally need to install a relay-regulator (or rectifier) in the electrical circuit. As well as if you already have more powerful coils of 18 Amp or 20 Amp, and they are usually put on 188F (13 HP) or 190F (15 HP) single-cylinder motors, or two-cylinder 2V77 (17hp), 2V78 (21hp), then for stable operation of the devices you will need, in addition to the coil, use a voltage regulator relay. In the case of coils more powerful than 7 Amperes. always. For this, Lifan produces, for example, such a relay-regulator (18 Amperes). or here is such a relay-regulator (20 Amperes). However, such powerful coils and the corresponding flywheels (plus the relay-regulator) are supplied as spare parts in very limited quantities. Lifan does this deliberately. The main reason for this is that customer redesigns (do it yourself) are not covered by the manufacturer’s warranty. On our website, we offer our clients such “pumped-over” engines of exclusively original factory assembly and design. All of them are assembled at the Lifan plant, specifically at the request of the Russian consumer. And they are fully covered by the entire factory warranty.
Specificity of selection and installation of lighting
Before installing the headlamp on a single-axle tractor, you need to decide on the equipment used. The choice of a lamp for lighting depends on the complexity and nature of the work being carried out, as well as the lighting requirements.
The more light is needed at night, the more power of the selected lamp should be.
Also, technical features arise when installing headlights. If the power of the generator is not enough to provide a constant flow of light, use 12 V batteries. It is recommended to use light equipment so as not to increase the load on a single-axle tractor.
Build a Cargo Tractor 168cc 6.5HP
DIY light on a walk-behind tractor: instructions on how to make
How to carry out lighting on motor vehicles from a generator? How is the headlight connected to the walk-behind tractor? How to make light on a walk-behind tractor without a generator?
- Lighting options for vehicles of any class
- Light without battery and generator
- How to make a headlamp for a uniaxial tractor?
- Electrical diagram
- Necessary tools for the job
- Disc plow: algorithm of actions
- Motoblocks and motor-cultivators (cultivators)
- Generator wiring diagram
- How to choose the right lighting coil
- Specificity of selection and installation of lighting
- For motoblocks with a belt drive
- For heavy motoblocks
- How to choose a generator for a walk-behind tractor?
- Connecting and checking the headlight
- Connection by means of an electric generator
- Possible difficulties and ways to solve them
- Possible malfunctions and their elimination