How much oil to pour into a trimmer. The time of continuous operation of the benzokosa is indicated in the instructions of the trimmer. On average, Kosim is 15-20 minutes, after which we mock a trimmer and let it cool for 3-5 minutes. Also, weather conditions provide for the duration of continuous work. In hot weather, when mowing high grass, thickets of weeds, under a large load, the trimmer overheating faster.

How much to fill in gasoline oil for a trimmer

If you bought a trimmer, a benzos, a motorcycle, a chainsaw and other types of equipment, then you probably know that two.Stroke engines are used as power units on them. These motors do not work on pure gasoline, like four.Stroke, but on a mixture of gasoline with butter. In what proportion should be diluted gasoline with butter for a trimmer. This question as a question is asked by each summer resident before preparing the tool for work. We will figure out in detail in this matter, since the dilution of gasoline with oil for a trimmer affects the life of the tool, and improper preparation of the mixture will lead to Rapid engine wear. What is the danger of excess or insufficient amount of oil in gasoline for a trimmer:

• If gasoline is diluted with a large amount of oil (above the norm), this will lead not only to a large amount of smoke, but also to the formation of a carbon on the walls of the cylinder and a drop in power. This incapacitance will cause wear of the piston, which will be diagnosed to reduce its performance
• If gasoline contains an insufficient amount of oil poured into a trimmer, then this is even more dangerous. After all, the working mechanisms of the engine will not be lubricated in sufficient quantities, which will ultimately lead to their Rapid wear (Rapid destruction of the piston rings and jamming of the motor occurs). With an insufficient amount of oil in gasoline, poured into a trimmer, the wear of the motor will occur ten times faster

So that you do not have to pay for errors at the cost of overhaul of the engine or buying a new tool, it is necessary to fill the fuel of the correct consistency into the tank from the first day. You can find out the ratio in the instructions for the tool, since models of different manufacturers can give different recommendations. Usually this ratio is the following norms:

• 1 to 25 or 1 liter of gasoline 40 grams of two.Stroke oil
• 1 to 40 or 1 liter of gasoline 25-30 grams of grease
• 1 to 50. This is added to a liter of gasoline 20 grams of oil

The value of 1 to 50 is considered standard (indicated on canister with butter for two.Stroke engines), but it is necessary to rely on it in the most extreme case, since the manufacturers indicate the recommended value of the proportion, and if it is not observed, the operational resource of a two.Stroke motor decreases.

In addition to observing the proportion, you must also learn to prepare the mixture. After all, the option of adding oil to the gas tank is categorically contraindicated, although some do so. If you bought a trimmer or a gas tank, you will need the consumables that you will use to prepare the mixture. The instructions for the preparation of the fuel mixture in the trimmer have the following view:

Prepare gasoline and two.Stroke oil, based on the above recommendations for choosing a lubricant and fuel Additionally, to prepare the mixture, you need to take a container or container. Typically, a plastic bottle is used for this, the choice of which needs an appropriate approach. It should be clean inside. Using a milk container and other drinks is not recommended

The best option is a mineral water container It is very important that the capacity has a whole value of volume, that is, 1 or 2 liters, so that you do not have to calculate how much oil is pouring into a bottle per 1.5 liters, 1.3 or 1.25 liters, because you can easily make a mistake so easily You will also need a syringe that is used as a measured device for dosing. For such purposes, a regular medical syringe for 10 cubes is suitable

It is desirable that the syringe has an exact measuring scale After preparing the necessary materials, you can proceed to prepare

Instructions for the preparation of the fuel mixture in the gasoline:

• First you should fill a plastic container. The container is filled with 2 fingers not supplemented to fit the oil
• The required amount of two.Stroke oil is typed in a syringe, and poured into a bottle with gasoline. You need to do just that, and not vice versa
• After adding a lubricant to the bottle, it requires to close it tightly with a lid and stir. However, take into account that the streaming needs oil with the designation “Pre mix”. If the container “Self mix” is on the container with oil, then you do not need to shake the container, and after connecting the substances, you can pour them into the tool tank

After preparing the fuel mixture for a trimmer, it remains to season the tool, and start work. How to correctly refuel trimmers, gas troops, chainsaws and other types of motor vehicles, consider in detail.

How much oil should be poured into a trimmer per liter of gasoline

Many people know popular with summer residents, residents of the village and communal services, many people know the trimmer tool under the definition of a motorcycle. But the mowing of grass and weeds is only one of the aspects of the use of the trimmer. He successfully copes with cutting young shoots in gardens, with cutting highly supported branches, with the cultivation of flower beds and greenhouses. You only need to change the standard gearbox for a special nozzle.Most trimmers are equipped with two.Stroke engines. Light, simple in order and quite powerful. The resource of engines on professional braids and bush cutters, such as Husqvarna or Echo, reaches 2,000 hours. According to real users, the Husqvarna trimmer worked for 7 years without engine repair. For household and semi.Professional trimmers, for example, Fubag or Champion, the resource is 400. 500 mothers.

How to prepare a fuel mixture for a trimmer

But such results are real if you know exactly how much oil is added to gasoline for a garden trimmer. The fact is that two.Stroke engines operate on a mixture of gasoline with butter. The fuel enters the cylinder, burns there, creating a working effort on the piston, and that part of the oil that did not have time to ignite, lubricates the moving parts of the piston group. When preparing a mixture for a trimmer to a liter of gasoline, it is necessary to add a strictly defined amount of oil. If there is too little lubrication, then the friction force will become too large and the motor will jam, and in the case of too much, the oil will fill the candle and the engine will staller. Also, with excess oil, the engine power will decrease, it will not develop the required revolutions and smoke much.When compiling a fuel mixture, it is necessary to calculate how much oil is needed per liter of gasoline, based not only from the standard proportion, but also from which brand of gasoline and oil is used. In the case of two.Stroke engines, it is very important.

Butter

For trimmers, a special two.Stroke oil is made, on the package of which there should be a note “2t”. Car, and even more so, transmission oil is strictly prohibited. Two.Stroke oil in three types is produced:

It all depends on what substances make up the oil base. Mineral oil is the cheapest and unreliable. Its use is justified only in household class trimmers, which work for 30-60 minutes a day with large interruptions. Most manufacturers of motorcycles of this level indicate that TS-W3 class oil is suitable for the engine. This means that you can use mineral, synthetic and semi.Synthetic oil 2t.

It is advisable to buy only those grades of oil that the manufacturer recommends for a professional class motorcycle. This is usually semi.Synthetics and synthetics with special additives. Manufacturers mark the oil in letters:

• That. For two.Stroke engines with a volume of up to 50 cubic centimeters;
• TV. For engines 50. 200 cubic centimeters;
• TS. For engines of motorcycles, snowmobiles, etc.D.

In motorcycles, if the type of oil is not indicated in the instructions, you can fill in all three modifications. How much oil is added to the fuel of the trimmer depends on the brand of the tool and the quality of gasoline. Also, on the packaging with butter, the letters FA, FC, etc. May occur.D. They show the level of smoke.

The closer the second letter to the beginning of the alphabet, the more smoke stands out during combustion. As a rule, high.Quality oil has very little. This indicator does not affect the choice of oil. Important than the inscriptions “Self Mix” and “Pre Mix”. The first phrase means that the oil dissolves independently, and the container with the second mixture must be shaken several times.

The best oils in the market are STIHL, Shell Helix Ultra, Oleo-Mac, Lukoil.

Fuel

It remains to choose which gasoline to fill in a trimmer. The choice is small-AI-92 and AI-95. The difference between them is quite significant. If the manufacturer’s instructions do not indicate which gasoline, then it is necessary to stop at AI-92.

It practically does not depend on the brand of gasoline, how much oil per liter of gasoline must be added if the fuel is high.Quality and fully corresponds to the declared brand.

Buy gasoline only at branded gas stations, there the risk of buying A-80 instead of AI-92 is almost zero.

If it is recommended to fill in AI-95, then do not use other brands of gasoline. If the engine starts, then it will work irrelevantly and quickly overheat. So you run the risk of disable a motor not only of a household trimmer, but also a professional.

Preparation of the mixture

Many novice users are sure that if you add oil oils to the fuel mixture more than necessary, it will benefit. This is not true. Uninhabited oil is not excreted from the engine with exhaust gases, but will settle inside in the form of soot. This plaque threatens the integrity of the piston. If you use the mixture with an excess of oil regularly, then the trimmer will be greatly smoke, and the drop in power is inevitably.

With a lack of oil, the trimmer will overheat, the piston rings will be destroyed and the piston jams. If the oil deficiency is insignificant, then the trimmer will work 30. 40% less than the resource. If the lubricant is not enough more than 20%, then the motor will jam after 20. 30 minutes of intensive work. Each instructions for the trimmer have proportions on how to dilute the fuel mixture. This is usually 1:25. 1:40 or 1:50. In practice, it looks like this:

• 1:25. 40 milliliters of oil per 1 liter of gasoline;
• 1:40. 25 milliliters of oil per 1 liter of gasoline;
• 1: 50. 20 milliliters of oil per 1 liter of gasoline.

By the table, you can determine how much oil is poured into a certain volume of pure fuel:

Many problems with motorcycles arise due to improperly prepared fuel mixture. In two.Stroke engines, lubrication is produced by special oil (not ordinary motor!) mixed with gasoline. If the oil is not mixed with gasoline, then the motorcycle will quickly fail. Oil/gasoline is mixed in the proportion specified in the instructions of the trimmer. This is usually 1:40 or 1:50.

The question often arises: 1:50 proportion is how much oil and gasoline?

Oil selection rules

Motor oil depending on the chemical composition:

• Mineral. Made of oil distillates and is intended for low.Power air.Cooled equipment;
• Semi.Synthetic. Is a mixture of mineral and synthetic oils and is suitable for 2T and 4T, as well as for air and liquid cooling;
• Synthetic. Produced on the basis of complex ethers and can be used in powerful equipment, as well as for work in difficult climatic conditions.

Depending on the classification of the API, the following groups of oils for trimmer engines can be distinguished:

• That. For low.Power equipment with an engine volume up to 50 cm³ and air cooling;
• TV-for powerful equipment with a motor volume of 50-200 cm³ and an air cooling system;
• TS. For a powerful two.Stroke equipment (motorcycles, chainsaws, lawn mowers, etc.) with a engine volume 50-200 cm³;
• TD. For motors of boats with liquid cooling.

To choose the optimal oil for a specific trimmer model, it is better to take into account the recommendations specified in the instructions. For motorcycle 2t usually used oil-TV and API-t.

Leading manufacturers of garden equipment themselves develop and produce oils for their equipment. Such lubricants most fully satisfy all the technical and operational characteristics of specific series of trimmers. For example, for STIHL motorcycles FS 5, it is best to use the STIHL HP or STIHL HP Super oil, for Husqvarna 143R, Husqvarna HP or Husqvarna LS oil is suitable. But for the brand Patriot, ordinary M-8V mineral oil is suitable.

Mixing rules

To prepare the fuel mixture, it is necessary to use clean and dry containers, which does not contain extraneous inclusions or pollution. It is not recommended to use plastic containers. After adding liquids in the required proportion, the mixture must be thoroughly mixed for 2-3 minutes. You cannot do the following:

• Add a small amount of oil directly to the gas tank of motorcycles, as this will not give a homogeneous mixture;
• First of all, pour oil, and then gasoline. Due to the difference in densities, with this order of adding components, a heterogeneous mixture is also obtained
• Anging the components “by eye”. With this approach, it is not possible to achieve an accurate proportion of gasoline and oil for a trimmer 1/50 or 1/40;
• Use polyethylene bottles, since the latter is dissolved by gasoline.

Instruments

The gasoline trimmer Patriot RT 3355 is designed to trim and mow low grass on lawns, streets, around trees, along the roadsides, on lawns and garden areas. The unit is successfully used on even and relief, uneven areas. The manufacturer improved the model taking into account convenient transportation and easy use: the bar is made by a detachable, quickly assembled and disassembled. The comfort of operation adds a wide shoulder belt with an adjustable length. Fast launch is simplified by the primer.

• Description of the Patriot RT 3355 model
• Preparation and pouring of the fuel mixture in the trimmer Patriot RT 3355
• Stages of launching a trimmer of gasoline Patriot RT 3355

Description of the Patriot RT 3355 model

• Universal aggregate: The use of trimmer line allows you to carry out work on cutting lawns and flower beds, a change to a cutting knife allows you to perform a cut of dry stake, weeds with a hard or elastic stem, a trinter trim.
• Comfortable management and operation. Using innovative protection against vibration in the design, the selection of the optimal balance of the tool.
• Handle and shoulder belt using ergonomic technology.
• The primer facilitates the start, removes the load from the starter.
• Maintenance is affordable and convenient. If necessary, quick repair and elimination of problems in the ignition and in the filtration compartment is carried out.
• Engine power 1.8 l.With. Allows you to productively carry out continuous work within 4-4.5 o’clock.
• Engine volume 033 l.
• A sharp knife with a diameter of 230 mm. Knife rotation frequency of 8000 rpm.
• Strong reliable trimmer line with diameter 2.4 mm.
• Capture width 460 mm.
• Cycling handle.
• Net 6.6 kg.
• Gross 8.6 kg.
• Dimensional dimensions 95 x 36 x 23 cm.

Preparation and pouring of the fuel mixture in the trimmer Patriot RT 3355

• The mixture for a two.Stroke engine is made only from original Patriot oils and high.Octane gasoline AI 92.
• For cooking, use a special canister from a trimmer configuration. Marking is adapted for gasoline and oil of a particular model 3355.
• Gasoline is poured to the mark for gasoline fluid.
• The corresponding brand of oil Patriot for a two.Stroke engine flows into it.
• With a few shakes, the mixture is brought into a homogeneous state.
• Preparation of the mixture in a conventional gasoline canister is performed with exposure to gasoline/oil 32: 1 proportions.
• The preparation of the fuel mixture directly in the trimmer tank is not recommended.
• It is recommended to prepare a portion of the mixture for one, maximum two gas stations.
• Pour the mixture with the engine turned off, away from the sources of open fire.

Stages of launching a trimmer of gasoline Patriot RT 3355

• The freshly prepared mixture is poured into the tank.
• It is transferred up to the “cold” position, the air damper lever.
• The ignition on the control handle is set to the “inclusive” position.
• 5-7 clicks on the primer button to fill the carburetor with a mixture.
• The trimmer is laid on a stable surface at a safe distance from objects and people. The contact of the trimmer head or cutting knife with the ground is avoided.
• The gas trigger is pressed on the control handle and is fixed in this position.
• A trimmer holds with one hand, and with the other hand stretches the starter handle until the “hook”. At this moment, the handle pulls sharply until the engine is launched.
• Install the lever of the air damper in the middle position.
• Starter handle must be pulled several times before the engine starts.
• Warm the engine 5-10 seconds. Transfer the lever of the air damper down. Press the gas trigger for unlock.
• Smoothly pressing the gas trigger, bring the engine to maximum speed. They start working.
• They produce kosbu, holding the trimmer tightly by ergonomic handles.
• For a heated engine, the operations described above are performed without pressing the primer. In this case, the air damper is placed in the lower position.

The result of calculating the fuel mixture:

To make it more convenient to measure the desired volume of oil in milliliters use a medical syringe of a larger volume, it costs inexpensively, sold in any pharmacy. Or use any measured container container.

Our calculator will help you count the desired proportion for refueling any benzo tool, for example: boat engine, chainsaw, trimmer, lawn mower, etc.D. In other words, you can independently and freely calculate the correct ratio of gasoline and oil for two.Stroke engines. Mixing instructions in the photo below.

It is important, before starting the calculation, read the instrument operation instructions, in particular with points: refueling volumes, the ratio of the fuel mixture. These data will be initial for the correct calculation.

For your convenience, the resulting result can be printed on a printer by clicking the “Print” icon. We will be happy with constructive Комментарии и мнения владельцев and reviews regarding the work of our service.

Keep in mind that the gas.Instrument.Tool has a period of running and the gasoline/oil ratio differs from the recommended.

How much to add oil to gasoline for a trimmer

Equipment for the care of lawns occupies an honorable place in the garage of a country house or a summer residence. Competitors. Motoblock or chainsaw. Lose to trimmers and lawnmands in popularity. Among the operations of service for motorcycles, maintenance, maintenance and regular refueling are highlighted.

Using a trimmer in the garden

In modern conditions, the purpose of the trimmer is to care for the lawn and the site as a whole. Unlike the traditional unit for the rotation of lawns, Trimmer has advantageous differences:

• High mobility. This allows you to use the device in hard.To.Reach and limited in terms of places.
• Universality. Depending on the type of vegetation, the working organs change, which allows you to cut grass of any height and stiffness.
• Simplicity of design. With timely maintenance, the trimmer does not require regular tuning, frequent repair.

When choosing a trimmer, analyze the operating conditions of the unit, which will help to make the correct selection of the type and power of the engine.

We select gasoline and oil for refueling

In the overwhelming number of cases for refueling a tall gas tank, gasoline with an octane number 92 is used.

But if the manufacturer indicates the 95th gasoline for a trimmer, then you should not save. The difference in price between two varieties is currently minimal.

The selection of oil should be taken carefully. API classification gives a certain order for liquids of two.Stroke engines:

• Class Ta. Air cooling motors. From mopeds to lawn mowers;
• Class TV. Low.Power motors up to 200 cm3 from chainsaws to light motorcycles;
• TS class. Motorcycles and snowmobiles;
• TD class. For use with yachts, boats and hydrofaters motors.

Thus, the oil of the last two categories is not allowed for use with trimmers. When purchasing oils from domestic sellers, we pay attention to the method of mixing fluid with gasoline. When the Self Mix marks. No additional conditions are required to mix two components. At the mark “Pre mix”. Forced mixing is necessary.

Do not ignore recommendations for the use of only recommended oils. Professionals such as STIHL and Husqvarna develop original recipes for their models, taking into account their temperature modes of operation, parts used. Do not deprive yourself in advance, saving in oil.

Practical guide for the correct preparation of the mixture

Before solving the issue of how to mix oil with gasoline for a trimmer, organizational issues should be completed. These include the following points:

• Storage of technical fluids. For gasoline, it is better to provide a metal canister, and leave the oil in the factory container. It is allowed to use a special two.Section canister for convenience.
• The volume of the cooked mixture. Do not cook in advance a large volume. It is better to pour gasoline into a benzoca, taking into account the planned volume of work. The uniformity of the mixture during long.Term storage will be violated.
• Mixture tool. An ideal device for the selection of oil and dosage accuracy is an analogue of a medical syringe. This will not only allow you to accurately measure the liquid, but also creates conveniently in work.

By the way, when buying oil, do not make a big stock. It is enough to buy the volume that you can spend per season.

Dilute in the correct proportion

The problem of how much oil is pouring into gasoline for a trimmer is aggravated by bringing different proportions in different sources. For example, this discrepancy is often found:

• Proportion 1:40 is indicated in the instructions for the unit;
• Value of 1:25 on the plastic container of the fuel tank;
• Proportion 1:50 on a plastic container for the preparation of the solution.

At the slightest doubt, pay attention to the packaging with oil. When determining the volume to pour oil into gasoline for benzocouses,The properties of fluid are taken into account. It is taken into account that two.Stroke engines do not like oil starvation. At the same time. The excessive enrichment of the mixture oil is capricious.

When determining how much you need to add oil to gasoline for a trimmer, use a standard proportion. For one liter of gasoline, 1000 ml is divided into 50, and a 20 ml of oil is obtained. If the poured volume is 500 ml, then the amount of lubrication is reduced in proportion to. It is easy to calculate the amount of gasoline for large volumes. If it is necessary to prepare a mixture for the Kostsov brigade, you will need 200 ml of oil per 10 liters of gasoline.

Why add

Important is the uniformity of mixing. Therefore, when adding oil to a liter of gasoline to a trimmer, the following algorithm is used. Half of gasoline is mixed with all the required oil volume. After thorough mixing, the volume of the mixture is brought to the nominal with the addition of the residual part of the gasoline.

Follow the cleanliness of the container, including the mixing container or a canister with gasoline. Do not use an improvised container of unprepared plastic for preparing a mixture. Even small portions of impurities or garbage will contribute to the failure of the carburetor. After preparation, pour gasoline to pour into a trimmer it is better with a container with a device that protects the mixture from the strait.

If you break the ratio

The mixture supplied to the cylinders is represented by gasoline-oil fog. Oil promotes lubrication of moving parts and surfaces in the cylinder. The lack of oil affects the resource of parts. With a large share of oil, it does not have time to burn. Deposits are formed, which over time are able to exfoliate from the walls of the cylinder, and leave the bully, wear out the surface of the cylinder walls.

During operation, try to remember how much oil per liter of gasoline for a trimmer is needed even with single gas stations. For example, when extracting the last drops of oil from the container, it is a mistake to think that a one.Time violation of the proportion will not change anything.

Do I need to dilute gasoline for a 4-stroke engine

The lubrication of parts of the cylinder.Piston group in a more perfect motor is carried out by the traditional method of spraying and under pressure. Therefore, you do not need to add oil to gasoline. Only control its volume in the working tank.

What oil to choose for refueling in a trimmer or types of lubricants

Trimmers and benzocoses operate on two.Stroke engines that have a simplified design. Rarely, but there are models of trimmers with 4-stroke engines that work on pure gasoline. Two.Stroke.Type power units do not have a compartment for pouring motor oil (oil crankcase), due to which the weight of the tool is reduced and their cost is reduced. If the rotating details of the motor are not lubricated, then in the end they will quickly fail. To prevent this, the trimmer is refueled not by clean gasoline, but by a mixture with butter. What kind of oil to dilute with gasoline for a trimmer?

First, remember or find out what types of oils are produced by chemical composition:

• Mineral fluids. Designed for small power technology, which has air cooling. This is the cheapest type of lubricant for motors
• Semi.Synthetic substances. They are used for technology, which has air and water cooling
• Synthetic. Suitable for all types of motors with different types of cooling. They do not require frequent replacement, and this type of lubricant is several times more expensive than mineral and semi.Synthetic

From the foregoing it follows that for a trimmer, oil with any composition is suitable. Mineral water, synthetics and semi.Synthetics. Oils with different chemical composition differs in price, so it is necessary to rely when buying on the recommendations of the tool manufacturer. The instructions indicate recommendation information about which types of oils are best used. If this is the TS-W3 standard, then it is not so important which composition should have a substance. In this case, you can dilute mineral water, semi.Synthetics and synthetics with gasoline.

It is interesting!The main thing when choosing oil is not to fall on the fake, since today you can very often find different types of lubricants for two.Stroke engines, which consist mainly of low.Quality oil products.

The ratio of gasoline and oil for a trimmer table. First launch and running.In gas.Cubs

Hello! Acquired the PRORAB 8406 trimmer 1. How to make gasoline with oil correctly and in what proportion? I did not find the original oil from Prorab, I bought Hungsvarna HP oil. In the instructions for the trimmer it is written from third-party oils, you can use the oil mif \ 4 class oils, API TC-TB. In the case of using another brand of oil, the proportion of the fuel mixture does not change. Standard proportion of the mixture 1:25. But in a specialized store “Specialist” that Hungsvarna HP was sold to me, I urgently advised to dilute at 1:50 (as it is written in oil). Actually the question: if the instructions are written to dilute the oil by 1:25, and 1:50 is recommended in oil, then in what proportion to breed? And 1:25 is how much? 40 ml? I will not turn off the engine if I scout at 1:50? 2. How to properly run the engine? In the instructions, in addition to starting and disconnecting, nothing is written. Maybe you don’t need running.In? I read that there are such trimmers that can work immediately after the purchase.

Do I need to lubricate the gearbox before work or there is already a factory lubricant? I hope for your help, thanks!

1) Gasoline is always divorced with oil in the proportion as indicated on the bank with this oil! With two.Stroke products (benzotrimers, chainsaws, etc.) You can use any oil for two.Stroke engines, except for boat two.Stroke engines. It is advisable to use oil from normal stores, where the probability of buying fake oil is minimal. It is better to take Husqvarna or STIHL oil. STIHL oil should be with a sealed neck. Beware of fakes. There is a risk of spoiling the piston immediately. 2) driving two.Stroke products is not done! Please remember this! All two.Stroke products are high.Speed and love exclusively work on full gas! No half.Gases are permissible! This leads to incomplete exhaust and shifts with oil sediments of the wall of the piston. As a result. Bullying piston. So the full gas and every 25-30 seconds are discharged gas for 1-2 seconds to let the product rest and return to the normal temperature regime. 3) a gearbox in motorcycles with a straight shaft must be scored by a new grease every 20 hours. Oil from there comes out naturally during operation. This is done so that dirt, dust, etc. D. So if you do not want to get to replace the gearbox, score special gear lubrication every 20 hours. It is not difficult and the whole operation takes no more than 3 minutes. Lubric tubes are sold in each store with garden equipment and cost from 100 to 300 rubles. 1 tube is enough for 3 years. —- The concept of running the tool comes down to working with incomplete load during the production of the first two or three fuel tanks. For example, during a mowing not thick, low grass or sawing dry, not large wood. In no case should you run into the instrument at idle by burning a few fuel tanks. As a result of such running.In on the Windows of the cylinder, a carbon carbon fumes form on the piston and in the muffler, which negatively affects the engine resource.

Trimmer, or Benzokos. A tool that cannot be dispensed with in the household. Over, its reliability, efficiency and long life depend on many factors.

For example, fuel quality. This means that you need to correctly select oil for a trimmer, follow the proportions when adding to gasoline and the rules for refueling the device.

See also: Volkswagen Crafter 30 2.5 TD MWB L2H2 4DV. Van, 89 l.S, 6MKPP, 2006. 2011.In emulsion or condensate in the engine (determination of a malfunction)

Trimmer oil: gasoline ratio, two.Stroke engines, proportion, how to dilute

Trimmer, or Benzokos. A tool that cannot be dispensed with in the household. Over, its reliability, efficiency and long life depend on many factors. For example, fuel quality. This means that you need to correctly select oil for a trimmer, follow the proportions when adding to gasoline and the rules for refueling the device.

What oil to choose

For effective operation of the trimmer, it is necessary to select oil for two.Stroke engines. This is due to the lack of an oil crankcase in such a device. The following classification is released depending on the chemical composition of the oil:

• Mineral ones. It is based on an oil distillate, suitable for low.Power technology and with an air type of cooling, but requires frequent replacement and can only be used in good weather in the warm season;
• Semi.Synthetic. Suitable for garden equipment with air and liquid cooling type;
• Synthetic. At the basis have complex ethers, do not require frequent replacement and can be used at any time of the year.

Oil for 2 stroke engines is characterized by good solubility and a feature of complete combustion. For a trimmer, it is recommended to use a lubricant that is suitable for devices with an air cooling system. Most often, the packaging indicates that the oil is intended for garden equipment and has the marking of the TA, TV or TS. Over, the last of them is most preferable.

Often manufacturers of benzos release suitable oil, so you can facilitate your choice if you select the liquid of the corresponding brand.

What gasoline to fill

Gasoline for a trimmer must be selected inequilled with an equal number of 92 or 95. As practice shows, AI-80 gasoline can lead to breakdowns of the device, which is a dubious savings.

The fuel should be fresh, that is, after buying it can be stored for no more than 60 days.

Other factors are affected by the quality of fuel, for example, the use of a special lubricant for benzocosa and breeding it in a separate container. It is also recommended to use special canists designed to store gasoline.

How to dilute gasoline with a trimmer oil

Dilute gasoline for a trimmer in the correct proportion. Insufficient amount of oil can lead to poor lubrication of the elements of benzokos, which contributes to Rapid wear.

The correct ratio can be found from the instructions for the trimmer. Most often it is 1:25, 1:40, 1:50. To obtain such proportions in 1 liter of gasoline, you need to add 40 ml, 25 ml and 20 ml of oil, respectively.

Diluting gasoline with lubricating fluid directly in the fuel tank is unacceptable, in addition, the proportion of oil and gasoline should be clearly observed. If you ignore this rule, then the operation of the trimmer engine can be unstable, which is why it will quickly fail.

• Petrol;
• Oil suitable for two.Stroke engines with an air cooling system;
• Canister, better metal;
• Mixing container is also better metal;
• Gloves;
• Respirator.

Make a mixture of gasoline and oil as follows:

• Pour 1 liter of gasoline into the container, add half the desired portion of the oil. Mix thoroughly, do it extremely carefully away from the sources of open fire.
• Add the rest of the oil to the gasoline for the trimmer and mix thoroughly again. Now fuel can be poured into a trimmer fuel tank.

The mixture can be stored for no more than three months, so it is better to dilute gasoline in such quantities that there is enough use.

See »lineup and features of Craftsman lawn mowers

For dilution, only high.Quality oil can be used, while it is recommended to purchase it only in trusted stores, for example in specialized hypermarkets.

How and how much to refuel

It is easy to refuel the fuel tank of the trimmer. To do this, place the tank so that the cover is placed on top. The amount of fuel depends on the trimmer model. This information is indicated in the instructions, there is also a mark directly on the tank.

Overfilling the tank is strictly prohibited.

This can lead to the fact that the fuel is overlooking the intake pipe and the fuel filter, which can cause the engine breakdown or fuel ignition.

When refueling a trimmer, you need to observe safety measures:

• Try to fill in the liquid so that it does not spill, you can use the watering can for this;
• If gasoline nevertheless spilled, then it needs to be wiped right away;
• The trimmer’s launch should start after the combustible container is removed in a reliable and safe place, preferably at a distance of more than 10 meters;
• With a long break between operations, drain the remaining fuel.

Correct proportion and compliance with the technology of mixing and refueling will help extend the life of the trimmer. In this case, it is recommended to choose only a high.Quality product of the corresponding brand.

How much oil is needed per 1 liter of gasoline for a chainsaw?

Recommended proportion oils to gasoline 1: 50, t. E. On 1l. Gasoline 20ml.

For the preparation of the fuel mixture, unhealthy petrol with an octane number of 92 and motor oil for two.Stroke air cooling engines in the proportion of oil recommended by manufacturers. The manufacturer recommends the use of oil Champion and breed it in proportion with gasoline 50: 1 t.

Fuel

It remains to choose which gasoline to fill in a trimmer. The choice is small-AI-92 and AI-95. The difference between them is quite significant. If the manufacturer’s instructions do not indicate which gasoline, then it is necessary to stop at AI-92. It practically does not depend on the brand of gasoline, how much oil per liter of gasoline must be added if the fuel is high.Quality and fully corresponds to the declared brand. Buy gasoline only at branded gas stations, there the risk of buying A-80 instead of AI-92 is almost zero.

If it is recommended to fill in AI-95, then do not use other brands of gasoline. If the engine starts, then it will work irrelevantly and quickly overheat. So you run the risk of disable a motor not only of a household trimmer, but also a professional.

Two.Stroke oil requirements for chainsaws

High.Quality two.Stroke oil for chainsaws should completely burn without the residues of ash or soot, while highlighting a minimum of smoke. High anticorrosion properties and thermo.Oxidative stability can provide maximum engine protection both in working condition and during the period of downtime. The composition of effective oils for the engines of chainsaws, motorcycle or motor cultivators must include certain additives to increase viscosity and solvents that will contribute to better mixing with gasoline. An important requirement for the quality of modern two.Stroke oils is their environmental safety.

If you do not have a special measuring canister with divisions that are included in the set of the Trimmer that deserves attention, or such a container is lost, then use any suitable container. Better glass or metal. Plastic can also be used, but you need to choose a bottle with hard walls.

The capacity of the vessel should be a multiple of 1 liter. You can take a bottle and 1.5 liters, but practice shows that it is not very convenient. You also need a medical syringe, preferably 20. 50 milliliters. First, gasoline is poured into the container, then an accurate amount of oil is added (by volume). The procedure cannot be changed.

If you have Pre Mix oil, then you need to close the bottle or canister and turn it upside down several times and shake it hard. If Self Mix oil, then it will dissolve on its own. The prepared mixture must be used throughout the day. If you know how much fuel is the trimmer spent on a certain amount of work (or time), then calculating the amount of the mixture is not difficult. Otherwise, before each refueling, dilute the new fuel so that the minimum amount remains until the end of the work.

Standard proportions

Often with the proportions of oil and fuel for reliable operation of motorcycles, problems arise. The reason for everything is absolutely different information in the sources. You may encounter the difference in data in terms of a dozen units, but it happens half. Therefore, you involuntarily think about how many oils per 1 liter of gasoline are needed: 20 ml or all 40. But for this there is a technical passport for the product that you purchase in the store. There should be a description of the device, instructions for its operation and instructions on the rules for preparing the fuel mixture.

First of all, it is necessary to take into account the information that the manufacturer recommends, since in the case of failure of the motorcycles, you can make your claims to him, and not a third.Party source. If there is no instructions in the passport, and even more so if the passport is missing, then we recommend looking for another trimmer model from a more reliable seller.

For all other cases, when you have a benzo.Cave model in your hands and there is no way to find out its technical features, there are standard proportions of the most likely components of the fuel mixture for a two.Stroke engine. Basically, these units use AI-92 gasoline and special synthetic oil, which contains a solvent for better mixing with fuel. Such oil evaporates slowly and has the ability to completely burn in the cylinder, without leaving a car.

The standard attitude of synthetic oil to gasoline is 1: 50. This means that 100 ml of oil needs 5 liters of gasoline, and in accordance with this, oil consumption per 1 liter of gasoline is 20 ml. Knowing the amount of oil required to dilute 1 liter of fuel, you can easily calculate any norms when preparing fuel for a trimmer. When using mineral oils, the ratio of 1: 40 is most often standard. Therefore, 1 liter of fuel will require 25 ml of such oil, and 125 ml per 5-liter canister.

During the work of benzokos, it will not be difficult to determine and adjust the actual amount of oil, the right specific model to a person who has a little experience in the operation of such a technique. You should only pay attention to exhaust gases (their color, toxicity of the smell), stability of the cycles, engine heating and developed power. About what consequences from the incorrect proportions of mixing gasoline and oil can be expected is lit in another section of the article. There are motorcycles operating on gasoline AI-95 brand gasoline. It should also be taken into account.

How to dilute gasoline with a trimmer oil

Dilute gasoline for a trimmer in the correct proportion. Insufficient amount of oil can lead to poor lubrication of the elements of benzokos, which contributes to Rapid wear. In case the oil is more than the olive formed on the pistons and spark plugs. Foreths on the moving parts of the engine interferes with normal operation and leads to the speedy breakdown of the motor.

What proportion is required for a specific trimmer model can be found from the attached instructions. Most often, for 2-stroke gasoline motors of motorcycles, the fuel mixture is used in a ratio of 50: 1, where 50 is part of the gasoline, 1-part of the oil. That is, 20 ml of oil should be added to 1 liter of gasoline. The table will help to choose the necessary ratio.

To correctly measure the proportions, use measured containers with a milliliter scale. For these purposes, a special canister with a double neck is perfect, it is designed to mix and storage of oilbenzin. For example, oil can be typed with a medical syringe without a needle. Before mixing liquids, make sure that there is no water, dust and particles of dirt in the container for the finished fuel mixture.

Diluting gasoline with lubricating fluid directly in the fuel tank is unacceptable, in addition, the proportion of oil and gasoline should be clearly observed. If you ignore this rule, then the operation of the trimmer engine can be unstable, which is why it will quickly fail.

It is not recommended to use plastic bottles or canists for this purpose. This is due to the fact that gasoline has the ability to dissolve plastic, which means that part of the plastic can get into the fuel tank, which can lead to a carburetor breakdown. Although there are special plastic canists with the marking “Flame”.

• Petrol;
• Oil suitable for two.Stroke engines with an air cooling system;
• Canister, better metal;
• Mixing container is also better metal;
• Gloves;
• Respirator.

In addition to protective equipment, do not forget about fire safety rules, because gasoline and engine oil are easily ignited:

• It is better to work on the street to avoid accumulation of gasoline vapor in the room;
• You can not smoke and create situations related to the emergence of a spark.

Make a mixture of gasoline and oil as follows:

• Pour 1 liter of gasoline into the container, add half the desired portion of the oil. Mix thoroughly, do it extremely carefully away from the sources of open fire.
• Add the rest of the oil to the gasoline for the trimmer and mix thoroughly again. Now fuel can be poured into a trimmer fuel tank.

The mixture can be stored for no more than three months, so it is better to dilute gasoline in such quantities that there is enough use.

For dilution, only high.Quality oil can be used, while it is recommended to purchase it only in trusted stores, for example in specialized hypermarkets.

The correct selection of oil for benzos

Two.Stroke engines are filled with a mixture of unhealthy gasoline and oil with 2t markings. In this case, you need to use the recommended gasoline AI-92. If you apply a brand with a higher octane number, the temperature of the flash and combustion will be higher, the valves will burn out prematurely. The same applies to the clock. The recommended composition is not the most expensive. But the use of another brand is unacceptable. Viscosity will change, this will lead to insufficient lubrication of ordinary products made without grinding high accuracy.

If the oil is added with excess, incomplete combustion will lead to the formation of a soil and an excessive exhaust into the atmosphere. A rich mixture is harmful to the engine. For a four.Stroke engine, the oil is poured separately from gasoline. It washes nodes, cools, reduces friction. In the process, the oil is polluted and after 50 working hours should be replaced. What kind of oil is poured into a benzoocos, indicated in the passport. The composition should have a 4t mark with a viscosity of 10w40.

The best oil for any engine is the recommended. However, Shel Helix Ultra oil is world famous. The company has been developing a new technology for obtaining synthetic oil from natural gas for 40 years. Pureplus technology made it possible to obtain an improved composition of basic oil. On its basis, with the addition of the necessary additives, leading manufacturers receive recommended oils for their equipment.

The choice of oil primarily depends on the recommendation of the manufacturer. So, oil for benzo.Chatting oil is used only corporate. The same oil is suitable for the brand of a knight, as the engines in the brand brands. There is an opinion of experts, oil of any manufacturer, designed for one type of equipment, is suitable for use on all brands. But if possible, it is better to use the recommended.

The path of oil recommended for the Khuskvarna benzocyes was investigated. The company has no its own production, only the spill. The product purchased wholesale is spilled into small containers, marked and enters the retail network. Perhaps the composition of the oil at the manufacturing stage added exclusive additives for Khuskvarna.