How to Wrap Fishing Line On a Petrol Trimmer Properly

Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that there is an instruction, but it still doesn’t work out. Let’s try to deal with this issue in this article.

So, to rewind the fishing line, you need, for starters, to remove the reel from the trimmer – it will be more convenient. The removal method will depend on the type of trimmer.

Remove the coil from the trimmer

How to Wrap Fishing Line On a Petrol Trimmer Properly

On small electric trimmers with the bottom position of the engine (when it is when working near the ground), the coil usually has two keys on its sides. We click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.

On electric and petrol trimmers with a curved bar (it is still not possible to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.

On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper one with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

More than 200 types of trimmers in one place at the lowest prices. Click and see

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding process

If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find the hole fixing the line on the inside of the reel, insert one end of the line there and start reeling the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, we take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If there are two grooves, then each antennae is wound on its own groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, we fix the ends in special grooves, and if they are not there, hold them with our fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.

Video: How to Wrap Fishing Line On a Petrol Trimmer Properly


If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.

There are still reels in which the line is threaded through a through hole on the inside. After that, the ends of the fishing line, without winding, are threaded completely through the holes on the outer casing of the reel, the reel is assembled and the button, which is usually pressed, is rotated so that the line can be released during operation as it wears out. Turn the button – the line itself is wound inside. At the same time, turning it in the “wrong” direction will not work, since it can only spin in one direction. If you get used to it, then you can wind the line onto such a reel without even taking it apart – you just need to combine the through hole of the inner drum with the holes on the outer case of the reel, and then thread the line into them.

That’s all for the matter. Good winding!

Despite the fact that gardening equipment has been used for a long time, for some owners of private houses it is still a novelty. That is why often questions arise about how to properly wind a line on an electric or gas trimmer.

This is essentially a simple operation, but all its stages must be performed correctly to achieve the desired result. Moreover, in the operating instructions, only a few manufacturers give an answer to this urgent question. Study the article and find out how the line is wound around the reel of the trimmer.

The procedure for winding fishing line on the trimmer reel

First of all, you should know that trimmers have different working nozzles. The reel can be designed for different lengths and thicknesses of fishing line – this point should be considered when purchasing supplies.

So, how do you charge the fishing line into the trimmer coil? All work is divided into several stages:

  1. First you need to disassemble the trimmer head.
  2. Unscrew the nozzle by rotating the drum to the right.
  3. Press your fingers on the two latches located on opposite sides of the slots, and remove the top cover of the nozzle. You can pry the cover with a screwdriver. This should be done carefully: the reels with automatic line feed have a spring, which can forcefully drop the lid along with all the contents of the reel.
  4. Remove scraps of old fishing line.
  5. Now you need to find the middle of the fishing line. To do this, rewind it to the required length (for example, 10 m), cut and fold in half.
  6. Hook the middle of the fishing line into an existing recess or insert it into the hole specially designed for this. And start winding. The direction is indicated by the arrow, which is usually applied to the body of the trimmer coil (usually against the rotation of the drum). Some models have a double-sided reel: in this case, the fishing line should be wound in different directions: one end – in one direction, the other – in the other, while the loop of the fishing line must be brought into the dividing slot located in the middle.
  7. Leave the loose ends of the fishing line about 20 cm long each. Later they will need to be fixed in the recesses.
  8. And finally, the last step will be drum assembly. Replace the washers and spring. On the upper ring of the reel there are two recesses where you need to fill the antenna line of the fishing line. Pass them through the holes and install the reel in the drum, trying to tighten the fishing line and not displace the spring.
  9. Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, the excess fishing line will be cut off by the cutting blade itself.

As you can see, it is easy to wind the line onto the reel of the trimmer: the main thing is to do everything right. And here are some more tips that will be useful to you when choosing a fishing line, its winding and subsequent work:

  • Fishing line is of different thickness and with different cross-section. The best option for winding is the "native" for this model of fishing line;
  • Never use a fishing line or metal cables for the trimmer. Such a replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawn mower, but also others;
  • The fishing line is cut off when the working trimmer comes into contact with solid objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the fishing line onto the reel;
  • Use a straight line for mowing grass and a pigtail line for coarse weeds. It is more durable and will not be permanently cut.

How to Wrap Fishing Line On Forester Trimmer

How to Wrap Fishing Line On Forester Trimmer

Despite the fact that gardening equipment has been used for a long time, for some owners of private houses it is still a novelty. That is why often questions arise about how to properly wind a line on an electric or gas trimmer.

This is essentially a simple operation, but all its stages must be performed correctly to achieve the desired result. Moreover, in the operating instructions, only a few manufacturers give an answer to this urgent question. Study the article and find out how the line is wound around the reel of the trimmer.

The procedure for winding fishing line on the trimmer reel

First of all, you should know that trimmers have different working nozzles. The reel can be designed for different lengths and thicknesses of fishing line – this point should be considered when purchasing supplies.

So, how do you charge the fishing line into the trimmer coil? All work is divided into several stages:

  1. First you need to disassemble the trimmer head.
  2. Unscrew the nozzle by rotating the drum to the right.
  3. Press your fingers on the two latches located on opposite sides of the slots, and remove the top cover of the nozzle. You can pry the cover with a screwdriver. This should be done carefully: the reels with automatic line feed have a spring, which can forcefully drop the lid along with all the contents of the reel.
  4. Remove scraps of old fishing line.
  5. Now you need to find the middle of the fishing line. To do this, rewind it to the required length (for example, 10 m), cut and fold in half.
  6. Hook the middle of the fishing line into an existing recess or insert it into the hole specially designed for this. And start winding. The direction is indicated by the arrow, which is usually applied to the body of the trimmer coil (usually against the rotation of the drum). Some models have a double-sided reel: in this case, the fishing line should be wound in different directions: one end – in one direction, the other – in the other, while the loop of the fishing line must be brought into the dividing slot located in the middle.
  7. Leave the loose ends of the fishing line about 20 cm long each. Later they will need to be fixed in the recesses.
  8. And finally, the last step will be drum assembly. Replace the washers and spring. On the upper ring of the reel there are two recesses where you need to fill the antenna line of the fishing line. Pass them through the holes and install the reel in the drum, trying to tighten the fishing line and not displace the spring.
  9. Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, the excess fishing line will be cut off by the cutting blade itself.

As you can see, it is easy to wind the line onto the reel of the trimmer: the main thing is to do everything right. And here are some more tips that will be useful to you when choosing a fishing line, its winding and subsequent work:

  • Fishing line is of different thickness and with different cross-section. The best option for winding is the "native" for this model of fishing line;
  • Never use a fishing line or metal cables for the trimmer. Such a replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawn mower, but also others;
  • The fishing line is cut off when the working trimmer comes into contact with solid objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the fishing line onto the reel;
  • Use a straight line for mowing grass and a pigtail line for coarse weeds. It is more durable and will not be permanently cut.

Video: How to Wrap Fishing Line On Forester Trimmer


Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that there is an instruction, but it still doesn’t work out. Let’s try to deal with this issue in this article.

So, to rewind the fishing line, you need, for starters, to remove the reel from the trimmer – it will be more convenient. The removal method will depend on the type of trimmer.

Remove the coil from the trimmer

On small electric trimmers with the bottom position of the engine (when it is when working near the ground), the coil usually has two keys on its sides. We click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.

On electric and petrol trimmers with a curved bar (it is still not possible to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.

On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper one with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

More than 200 types of trimmers in one place at the lowest prices. Click and see

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding process

If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find the hole fixing the line on the inside of the reel, insert one end of the line there and start reeling the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, we take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If there are two grooves, then each antennae is wound on its own groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, we fix the ends in special grooves, and if they are not there, hold them with our fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.

If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.

There are still reels in which the line is threaded through a through hole on the inside. After that, the ends of the fishing line, without winding, are threaded completely through the holes on the outer casing of the reel, the reel is assembled and the button, which is usually pressed, is rotated so that the line can be released during operation as it wears out. Turn the button – the line itself is wound inside. At the same time, turning it in the “wrong” direction will not work, since it can only spin in one direction. If you get used to it, then you can wind the line onto such a reel without even taking it apart – you just need to combine the through hole of the inner drum with the holes on the outer case of the reel, and then thread the line into them.

That’s all for the matter. Good winding!

How to Wrap Trimmer Fishing Line Properly Video

We wind the fishing line onto the reel correctly!

How to Wrap Trimmer Fishing Line Properly Video

Fishing is a really exciting and fascinating affair. Novice spinningists, of course, want to quickly join him and finally get an sensible result. The reservoir where you are going to fish is selected, all the necessary accessories are bought. There are rods, reels with baits and fishing lines – too. However … Even directly on the shore, even a minor, but still tangible nuisance can wait, which sometimes completely disrupts all fishing.

Her name is winding fishing line. Each coil is equipped, it seems, with an instruction with a basic circuit. But the fact is that with such an attitude a lot can not be caught for sure. With improper winding, the loop can be reset, and instead of removing the fish from the hook, you will have to bother with unraveling the lump from the fishing line with your own hands.

The structure of the winding line can also be very different, it depends on the chosen reel

Start using spinning most often with gear that is shorter (both reels and rods). The caliber of the bobbin in them is two to three thousand (that is, a hundred-meter line is not more than a third of a millimeter thick in this case, the limit). The winding structures can also be very different: this is a chaotic winding in a random arrangement of Chinese samples (more or less suitable for monofilament, but completely inappropriate with braided fishing line), and such more professional formats as a straight cylinder, straight and inverted cone. And from the very beginning it is better to accustom yourself to those types of styling that are more serious, because this is not a whim, but higher efficiency. Having saved fleetingly several hundred rubles, then you will begin to curse everything in the world, when instead of casting and biting (well, or just casting and waiting), fishing will turn into a continuous struggle with “beards” and other fishing line overlays. Such fishing has never brought joy to anyone.

How to quickly wind a line onto a spinning reel

How to wind the line onto the reel. First of all, we fasten the bobbin to a motionless rod-shaped object

The basic, fundamental rule – the equipped fishing line must be as flat as a ruler. For a cylindrical winding, a straight line is optimal, and if a cone is chosen, it is inclined. But in any case, remember it firmly, only fishing line without bends.

How to ensure such leveling in practice? First of all, we fasten the bobbin to a motionless rod-shaped object on which it should easily and freely scroll. Pencils and knitting needles, fountain pens and screwdrivers, small metal tubes without sharp edges, and even a straight and well-polished stick can serve as a rod. As a last resort, find someone who agrees to hold.

Knots for attaching fishing line to the reel

Pull the fishing line through every single rod ring. Tie a knot at the elongated end. Now you can start refueling fishing line on the surface of the reel. First, we attach it over the bobbin in a circle, having previously lifted the arc of the logger, and when another node of the Arbor type is tied and tightened, the arc can be omitted.

The braid line is very fond of slipping. This can be avoided if a piece of rubber (for example, cut off from an unusable fingertip or a worn glove) is poked under the attachment point, in extreme cases, support it with a band-aid if there is no rubber.

And here comes the turn of winding fishing line. Turn the knob on the spool gently and evenly. Make sure that the line goes tight all the time. It must be maintained, but only in tight gauntlets.

When winding, avoid, as far as possible, completing it at the level of the sides of the bobbin. If this rule is not observed, then self-resetting of loops or their terrible tangling become very probable. To avoid this outcome, pay attention to the side even though a millimeter or two remain unreelted fishing line. On the other hand, exceeding a gap of five millimeters may make long-range casting impossible. Prevention is backing (in fact – reeling up the bottom of the main fishing line from the auxiliary, not thicker than three tenths of a millimeter, otherwise even laying will be unattainable). Keep in mind that almost all threads work well in backing, except for long-drying cotton and nylon.

Video: How to Wrap Trimmer Fishing Line Properly Video


Watch a useful video: how to wind a fishing line onto a reel

To determine how much fishing line to throw on backing is possible only by experiments, there are no ready-made formulas and theoretical provisions on this subject. It will take another bobbin. We wind the main forest onto it, then backing (do not forget about the clearance from the side). Next we attach the main mount, on which we are already introducing fishing lines in the reverse order. Check out our website and read more helpful tips for fishermen.

Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that there is an instruction, but it still doesn’t work out. Let’s try to deal with this issue in this article.

So, to rewind the fishing line, you need, for starters, to remove the reel from the trimmer – it will be more convenient. The removal method will depend on the type of trimmer.

Remove the coil from the trimmer

On small electric trimmers with the bottom position of the engine (when it is when working near the ground), the coil usually has two keys on its sides. We click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.

On electric and petrol trimmers with a curved bar (it is still not possible to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.

On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper one with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

More than 200 types of trimmers in one place at the lowest prices. Click and see

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding process

If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find the hole fixing the line on the inside of the reel, insert one end of the line there and start reeling the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, we take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If there are two grooves, then each antennae is wound on its own groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, we fix the ends in special grooves, and if they are not there, hold them with our fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.

If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.

There are still reels in which the line is threaded through a through hole on the inside. After that, the ends of the fishing line, without winding, are threaded completely through the holes on the outer casing of the reel, the reel is assembled and the button, which is usually pressed, is rotated so that the line can be released during operation as it wears out. Turn the button – the line itself is wound inside. At the same time, turning it in the “wrong” direction will not work, since it can only spin in one direction. If you get used to it, then you can wind the line onto such a reel without even taking it apart – you just need to combine the through hole of the inner drum with the holes on the outer case of the reel, and then thread the line into them.

That’s all for the matter. Good winding!

How to Wrap Fishing Line On Champion Trimmer Properly

How to Wrap Fishing Line On Champion Trimmer Properly

  1. Instruction manual
  2. Common mistakes

Almost every novice when using a trimmer is faced with the problem of changing the line. Despite the fact that changing the line is very simple, you must learn to do it right. Replacing the fishing line with proper dexterity will take no more than five minutes – just enough to constantly practice it. This article will discuss replacing fishing line with Patriot trimmers as an example.

Instruction manual

In order to change the fishing line, you must remove the old one (if it was).

A coil is a part of the trimmer design, which is located inside the head of the lawn mowing, drum or reel. Depending on the manufacturer, the heads may be different. But this article only discusses Patriot, although their mechanism is used by many other companies.

Instructions on how to unwind the hand head on the trimmer are described below.

  1. First of all, you need to clean the head of dirt and adhering grass, if it is dirty. To do this, it is necessary to raise the lawn mowing head up and, holding the casing, remove the special protective cover, dressed on the drum.
  2. The next step is to remove the coil from the drum. The reel is easily removable even with one hand, because it is not fixed inside the drum.
  3. The drum itself is bolted to the trimmer. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with the reel, while unscrewing the screw counterclockwise.
  4. Now you can pull the coil out. As mentioned above, it is not fixed by anything, except for a hook with a metal shaft, so it does not need to be pulled out with force. Carefully, in a circular motion, pull the reel out of the drum.
  5. Now it remains to remove the old fishing line and follow the following instructions.

Installing the reel and drum in its original place is performed according to the inverse algorithm.

Before refueling the fishing line, you should make sure that a thread suitable for the trimmer has been purchased. In the event that the thread is not suitable, the fuel or energy consumption increases, as well as the load on the engine of the lawn mowers.

In order to directly replace the thread itself, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m of fishing line. The specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to determine the exact length, it can be done as follows: insert and twist the thread to such a state that the reel is fully charged (the level of the fishing line compares with the protrusions on the sides of the reel). Care must be taken to ensure that the line sits in the reel evenly.

The instructions for refueling fishing line are described below.

  1. The prepared thread must be taken and folded in half. It should be ensured that one edge is 0.1-0.15 m longer than the other.
  2. Now you need to take the ends in different hands. The one that is smaller must be pulled to the larger, so that it becomes 2 times shorter. When bending, an indent of 0.15 m should be maintained.
  3. Locate the slot inside the coil baffle. Carefully thread the loop that came out earlier into this slot.
  4. To continue work, it is necessary to determine the direction of winding the thread in the bobbin. To do this, it is enough to inspect the coil – there should be an arrow on it.
  5. If the pointer arrow could not be found, then it is entirely possible that there is a written designation. An example is shown in the photo below. Inspect the coil head. It has a direction indicator. However, this is the direction of movement of the coil. To get the direction of winding, you need to wind in the opposite direction.
  6. Now you need to fill the reel with fishing line. It is worth paying attention that inside the coil there are special guide grooves. When wrapping the thread, these grooves must be followed, otherwise the trimmer may be damaged. At this stage, you need to charge the coil very carefully.
  7. When the user winds almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15 m) and stretch it into the hole located in the wall of the coil. Now you need to repeat this action similarly with the other end (on the other hand).
  8. Put the coil itself in the head of the spool, before threading the line through the holes inside the drum.
  9. Now is the time to put the drum back in its place. After that, you need to take the ends of the fishing line with both hands and pull them to the sides. Then you need to put the cover back in place (here you can safely make efforts until you hear a characteristic click).
  10. It remains to perform "cosmetic work". We need to see if the thread came out too long. You can start a trimmer and check in practice whether everything is comfortable. If the thread comes out a little long, you can cut it with scissors.

Video: How to Wrap Fishing Line On Champion Trimmer Properly


Common mistakes

Although winding a fishing line is a very simple task, many beginners may not wind a fishing line correctly. Below are the most common errors.

  1. Many people when measuring the thread think that 4 m is a lot. Because of this, people often measure less, and, accordingly, they do not have enough fishing line. Do not be afraid to measure a lot, because you can always cut off the excess.
  2. In a hurry, some people do not observe the filling grooves inside the spool and wind the thread at random. This leads to the "flight" of fishing line from the reel and can even cripple.
  3. For winding, use only the appropriate fishing line. This error is most common. You need to monitor not only the thickness and volume of the fishing line, but also its type. Do not use the first caught fishing line for wrapping, which will not meet the goals. For example, it is not necessary to use a thread on young grass if it is necessary to mow dead wood.
  4. Do not turn on the device until it is fully wound and collected. Although this is obvious, some people do this in order to check if everything is done correctly.
  5. In no case should you confuse the direction of refueling, as this will overload the engine, and it will soon go out of operation.

Beginners are quite prone to make mistakes, therefore You must follow the tips in this article.

To learn how to replace a fishing line on a Patriot trimmer, see below.

Despite the fact that gardening equipment has been used for a long time, for some owners of private houses it is still a novelty. That is why often questions arise about how to properly wind a line on an electric or gas trimmer.

This is essentially a simple operation, but all its stages must be performed correctly to achieve the desired result. Moreover, in the operating instructions, only a few manufacturers give an answer to this urgent question. Study the article and find out how the line is wound around the reel of the trimmer.

The procedure for winding fishing line on the trimmer reel

First of all, you should know that trimmers have different working nozzles. The reel can be designed for different lengths and thicknesses of fishing line – this point should be considered when purchasing supplies.

So, how do you charge the fishing line into the trimmer coil? All work is divided into several stages:

  1. First you need to disassemble the trimmer head.
  2. Unscrew the nozzle by rotating the drum to the right.
  3. Press your fingers on the two latches located on opposite sides of the slots, and remove the top cover of the nozzle. You can pry the cover with a screwdriver. This should be done carefully: the reels with automatic line feed have a spring, which can forcefully drop the lid along with all the contents of the reel.
  4. Remove scraps of old fishing line.
  5. Now you need to find the middle of the fishing line. To do this, rewind it to the required length (for example, 10 m), cut and fold in half.
  6. Hook the middle of the fishing line into an existing recess or insert it into the hole specially designed for this. And start winding. The direction is indicated by the arrow, which is usually applied to the body of the trimmer coil (usually against the rotation of the drum). Some models have a double-sided reel: in this case, the fishing line should be wound in different directions: one end – in one direction, the other – in the other, while the loop of the fishing line must be brought into the dividing slot located in the middle.
  7. Leave the loose ends of the fishing line about 20 cm long each. Later they will need to be fixed in the recesses.
  8. And finally, the last step will be drum assembly. Replace the washers and spring. On the upper ring of the reel there are two recesses where you need to fill the antenna line of the fishing line. Pass them through the holes and install the reel in the drum, trying to tighten the fishing line and not displace the spring.
  9. Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

When you turn on the trimmer, the excess fishing line will be cut off by the cutting blade itself.

As you can see, it is easy to wind the line onto the reel of the trimmer: the main thing is to do everything right. And here are some more tips that will be useful to you when choosing a fishing line, its winding and subsequent work:

  • Fishing line is of different thickness and with different cross-section. The best option for winding is the "native" for this model of fishing line;
  • Never use a fishing line or metal cables for the trimmer. Such a replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawn mower, but also others;
  • The fishing line is cut off when the working trimmer comes into contact with solid objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the fishing line onto the reel;
  • Use a straight line for mowing grass and a pigtail line for coarse weeds. It is more durable and will not be permanently cut.

How to Wrap Fishing Line Coil Trimmer Correctly

Many, having developed a factory line on a newly acquired trimmer, try to rewind a new one, but they cannot, because they do not know how to wind the line onto the reel spool (bobbin). It seems that there is an instruction, but it still doesn’t work out. Let’s try to deal with this issue in this article.

So, to rewind the fishing line, you need, for starters, to remove the reel from the trimmer. it will be more convenient. The removal method will depend on the type of trimmer.

Remove the coil from the trimmer

How to Wrap Fishing Line Coil Trimmer Correctly

On small electric trimmers with the bottom position of the engine (when it is when working near the ground), the coil usually has two keys on its sides. We click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is taken out, on which the fishing line is directly wound. When parsing, be careful: there is a spring inside that can fly out and get lost.

On electric and petrol trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to grab the coil body with one hand, and with the second hand you need to start turning the lamb on it. It is he who fastens the coil to the trimmer bar. Having unscrewed the lamb, carefully remove the entire coil, being careful not to lose the spring inside.

On electric and petrol trimmers with a straight rod and a gearbox at its end (in addition to fishing line, you can also install a knife on such trimmers) we look for a hole under the coil, insert a screwdriver into it, for example, rotate the coil quietly until the screwdriver penetrates even deeper, and the coil will lock. Now twist the entire coil clockwise (since the thread is left) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using latches or twisted by a lamb. If the coil is on latches, then we press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just twist the lamb. There may also be a third type of connection of two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper one with the other, and start turning them in opposite directions. When disassembling such a coil, you must also make sure that the spring inside is not lost.

Video: How to Wrap Fishing Line Coil Trimmer Correctly


than 200 types of trimmers in one place at the lowest prices. Click and see

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding process

If your coil is designed to work with only one antennae, then everything is simple. You need to rewind 2-4 m of fishing line (depending on the size of the reel), find the hole fixing the line on the inside of the reel, insert one end of the line there and start reeling the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate an arrow, in which direction to wind the line. After winding up the fishing line, we leave a small piece of it unwound to expose it. We fix this piece in a special groove located on the inside of the reel and designed so that the fishing line does not unwind at the time of collection of the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the reel. Next, we take the outer part of the reel and thread the outer piece of fishing line into the existing hole, collect and put the reel back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we see how many grooves are available for winding fishing line. There may be one or two. If there is one groove, then both antennae are wound along this same groove. If there are two grooves, then each antennae is wound on its own groove. The reel with one groove should have a through hole into which the line is threaded. Unwind 2-4 m of fishing line, thread it through this hole so that on each side of the fishing line sticks out equally. And at the same time we wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little fishing line unwound, we fix the ends in special grooves, and if they are not there, hold them with our fingers. Pass both ends into the holes on the outer coil body. We assemble the coil and attach it to the trimmer.

If there are two grooves, we fold the piece of fishing line 2-4 m long in half, insert the loop obtained at the bend point into the groove between the two grooves, and simultaneously wind both ends of the fishing line in each groove. Further actions are similar to the previous option.

There are still reels in which the line is threaded through a through hole on the inside. After that, the ends of the fishing line, without winding, are threaded completely through the holes on the outer casing of the reel, the reel is assembled, and the button, which is usually pressed, is rotated so that the line can be released during operation as it wears out. Turn the button. the line itself is wound inside. At the same time, turning it in the “wrong” direction will not work, since it can only spin in one direction. If you adapt, then on such a reel you can wrap the fishing line without even taking it apart. you just need to combine the through hole of the inner drum with the holes on the outer casing of the reel, and then thread the fishing line into them.

That’s all for the matter. Good winding!

How to Wrap Fishing Line Coil Trimmer Correctly?

How to wind a fishing line on a trimmer

To wrap a fishing line on a gas or electric trimmer, you do not need to have any special skills. To begin with, it is important to determine the appropriate consumables, and then choose the best method. Fill fishing line into the reel of the device using two different methods.

Types of Trimmer Heads for Coils

The main elements of the trigger is a mowing head, which is a cylindrical body with a coil (bobbin) inserted inside. The fishing line (cord) is refueled into it. The heads differ from each other in the way the cord is fed and refueled. There are three types of heads:

  • Automatic. Submission of fishing line is carried out after this, as the user reduces engine speed. Automatic feed of the cord is very convenient when you need to perform a large amount of work. The disadvantage of such a head is the high consumption of thread.
  • Semi-automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its work is arranged so that the fishing line begins to automatically lengthen at a time when the trimmer is working at full speed. It is only necessary to slightly hit the head of the apparatus on the ground (this will remove the blockage of the fishing line), and the cord will be pulled out of the bobbin due to centrifugal force. Then the fishing line is cut to the required length with a knife, which is located on the protective casing.
  • Manual To lengthen the cord, you must stop the device. After that, the fishing line will need to be pulled out manually.

How to Wrap Fishing Line Coil Trimmer Correctly?

Types of trim coils

Fishing line selection

To ensure that the fishing line in the trimmer head is successful, it is important not to lose money with the choice of consumables. The thicker the cord you fill, the thicker and tougher the grass it can cut. Often used universal fishing line, the diameter of which is 2 mm. You can select the diameter suitable for the mower in the following ways:

  • See the line thickness information in the instructions that came with the trimmer.
  • Pay attention to the bobbin itself. Sometimes it displays information about the possible diameters of the fishing line.
  • Another option is to try inserting the cord into the outlet. If it easily passes into it, then the selected diameter of the fishing line is suitable for use.

Trimmer reel

You can pick up the cord by the type of engine. If the fishing line is too thick, the rotation resistance will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

  • For an electrical device with an engine less than 500 V, a thread 1.3 mm thick is suitable. If this was not found, then you can use a 1.6 mm fishing line. If the power is greater than 1 kW, then select a cord with a diameter of 2 mm.
  • For a gas trimmer, a shaft mower matters. For a bent version, a 2 mm cord is often used. If the shaft is straight, install a thread of 2.4–2.5 or 3 mm. The thickest fishing line is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross-section of the cord. Some popular options:

  • The most common fishing lines with a circular cross section. They mow fresh herbs well, but do worse with shrubs, dead trees.
  • Twisted (spiral) cord is not very strong, but not bad for thin young grass.
  • A serrated thread with sharp edges is ideal for large weeds in a neglected area.
  • You can even mow the lawn with a rectangular, star or square fishing line for a trimmer, but they are not very durable.
  • The most durable is a two-component cord with an inner core and a round cross-section.

Types of fishing line for trimmer

Please note that instead of fishing line, wire, metal strings and cables, as well as ordinary fishing thread, cannot be used. The device will be dangerous for both the user and others. So the cable or similar products will gradually start to work, as a result, their ends will unravel, and small pieces will fly apart at high speed.

Removing and disassembling the coil

The mowing trimmer head consists of a casing, a spring (not in every model), a bobbin with cord, and a cover. Before proceeding to disassemble the coil of the electrical unit, be sure to disconnect the trimmer from the mains. The disassembly method depends on the attachment of the mowing head. First option:

  1. To remove the cover that covers the inside of the head, press on the latches (latches), which are located on its two sides.
  2. Remove the cover under which you will see the spool. remove it from the housing. For some trimmer coils, there is a spring under the bobbin, which must also be carefully pulled out.
  3. Having removed the bobbin, you will see a screw in the center of the case. Unscrew it with a screwdriver.
  4. After removing the fasteners, take the body of the part and, swinging it in different directions, remove the gearbox from the shaft.

In the second embodiment, the trimmer head is screwed onto the gear shaft. To remove it, you need to fix the shaft. For this, a hole is provided in such devices through which a thin screwdriver or metal rod is inserted. Brief Instruction:

  1. Insert a screwdriver into the special hole, and then lock the shaft.
  2. Grasp the body of the head and start twisting it. This should be done clockwise, since the thread on the shaft is left.

Winding fishing line on a reel

Winding fishing line

Filling the fishing line into the reel of the trimmer is a relatively simple procedure, provided that you follow a certain algorithm of actions. When you need to determine how many meters of consumable material is enough, wind it onto the bobbin so that the coil does not exceed the diameter of the sides. Having determined the cord length, follow the following instructions:

  1. Fold the consumable in half so that one end of the line is 10-15 cm longer than the other.
  2. You need to start charging with the central side, which divides the trimmer bobbin into 2 parts. Find the groove where the cord should be inserted. Bend the latter in half.
  3. Decide in which direction you need to wind the line. To do this, look at the bobbin, which may be an arrow or an inscription. She indicates the side of the winding. If there are no signs on the reel, then look at the arrow on the mowing head. carry out the winding in the opposite direction.
  4. Wash the consumables carefully, turn to turn. Try to maintain maximum thread tension.
  5. After laying the cord, fasten the short end of the material first. To do this, insert it into the groove on the side of the coil, which will fit in diameter. Second end (genuine), attach to the groove on the other side of the trimmer bobbin.
  6. After fixing the fishing line, cut off its ends. Remember to leave allowances of approximately 10 cm.
  7. Install the refilled coil to the mower head of the device. To do this, you need to alternately insert and pull the thread into the outlet of the head, then to place the bobbin of the device in the skin.
  8. After applying the required force, pull the cord out of the locking grooves and tighten the material. At the end of this step, put on the cover and secure it with the latches.

Step-by-step winding of fishing line onto a reel

You can wind the cord on the trimmer in another way, in which two pieces of material are charged instead of one. Replacement is as follows:

  1. Bend one end of the cord in the form of a hook.
  2. At the bottom of the bobbin there should be a hole that is designed to fix the fishing line. Insert the bent end of the thread there.
  3. Wind the cord material in the direction of the arrow to the desired level, which does not exceed the diameter of the trimmer coil.
  4. The same actions need to be done for the second bobbin cell.
  5. Assembling the head of the device is similar to the first method.

Video

How to reel a fishing line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable assistant in the arsenal of a modern summer resident or the owner of his own house.

Thanks to these garden devices, you can easily mow down even a large garden plot. After acquiring this tool and doing a few tricks, many people think about how to properly wind the line onto the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since developers often do not fully reflect the instructions for replacing the fishing line in the instruction manual.

Preparation for winding fishing line

Prior to the winding process, it is necessary to remove the reel with fishing line from the housing. Depending on the manufacturer, power and type (electric or gasoline), there are three structural types of trimmers:

    Compact electric trimmers.

Straight Bar Trimmer

In such a model, it is possible to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To install the trimmer knife, it is necessary to combine the hole of the bobbin and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, it is easy to unscrew the housing by hand clockwise.

Winding fishing line on trimmer

The measured and accurate dismantling of the spool from the spit reel makes it possible to go directly to the winding of the fishing line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of reels, depending on the number of antenna line fishing line and methods of refueling:

  1. Trimmer head with one working antennae;
  2. A bobbin with two antennae fishing line;
  3. Auto winding reel.

Single-Barrel Trimmer Coil

Single-mustache coil brush

Many owners and specialists note the simplicity of operation and refueling reels with one mustache. Depending on the manufacturer, the length of the fishing line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and winding is made in the direction opposite to the working rotation of the bobbin. Most coils on the outside of the case have marks in the form of arrows that indicate the direction of movement of the trimmer bobbin.

After winding, you need to leave a free end of 15-30 cm to enhance centrifugal force, which is crucial when removing the trimmer line in automatic and semi-automatic reels. We pass the left end through the working hole of the coil and assemble the head.

Double Antenna Trimmer

Two groove head

After removing the spool from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but with careless refueling in a twin groove, there are problems with operation. Due to the likelihood of weaving adjacent tool strings, a situation may arise when it is impossible to remove new ones after wear of the working antennae.

Regardless of the number of streams for refueling, a fishing line from 1.5 to 3 meters long is taken. Winding must be done in the direction opposite to the rotation of the head, since winding in the direction of travel will cause the line to not be removed from the reel. After the fishing line is tucked into the trimmer coil, free ends (15-30 cm) are threaded through special holes. Next, we collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the guard will cut off the excess.

Trimmer head with automatic threading

Types of Trimmer Heads

In some models available on the market, a reel with an automatic winding mechanism is installed. It is enough for the owner to correctly tuck and fix the ends in the head, and the tool itself will perform the winding operation when it is switched on in the operating mode. It is almost impossible to wind a fishing line into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of an automatic trimmer head include the ease of refueling fishing line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

Video: How to Wrap Fishing Line Coil Trimmer Correctly?


How to wind a fishing line on a trimmer reel: winding methods and video

Any garden owner knows how quickly weeds can flood the area. To defeat them without excessive efforts will help the trimmer. This incredibly useful device is an indispensable tool for trimming and mowing grass.

It’s no secret that a conventional lawn mower can be used far from everywhere. In contrast, the trimmer can handle even very complex areas. This is especially true for those tools in which the cutting element is not a knife, but a fishing line.

Features of the use of trimmers

The trimmer mowing grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, aisles in the garden.

Such a convenient, and most importantly, effective device, as a trimmer, exists in several variations:

As the names indicate, the types of trimmer are noticeably different from one another. But regardless of the type of tool, it the cutting element may be a fishing line. Of course, the line tucked into the reel of the trimmer is not infinite. And sooner or later it will be required to replace it with a new one.

The consumption of fishing line depends on on frequency of use device and scope of work performed. The more grass is cut and the more often it is trimmed with a trimmer, the more actively the line is consumed in it. And, accordingly, the faster it will end. In this regard, the question arises: how to fill the fishing line into the coil of the trimmer?

Not everyone knows the answer to this question. But winding fishing line on a reel plays an important role in the trimmer. In order for the device to function normally, it is very important to correctly wind a new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

Which fishing line to choose

Before you stock up on this material for refueling in the trimmer, you need to make a choice. After all, the usual so-called round fishing line is far from the only existing species. How to choose the most suitable? First you need to determine the working conditions.

Type selection. A fishing line with a circular cross section is the most common. It will fit any coil with the rarest exceptions. This type of consumable is suitable for mowing fresh, juicy grass. But mowing the so-called dead wood, this species may no longer be able to cope. It is pointless to mention attempts to mow shrubs with this thread.

Besides the usual type, there are others, having sharp edges. Usually they are made with an “asterisk” or “square”. The presence of sharp edges is the main feature and key difference of these threads.

It is because of this peculiarity that the threads of such species are able to mow dry weeds. But the pointed threads are not without flaws, the main of which can be called quick wear and strength noticeably inferior to the round type.

In addition to the types of woods already mentioned, there are also interesting and common varieties. Especially among them can be noted fishing lines, inside of which stretched metal wire. Threads of this type are often used in tools that run on gasoline and have an engine more powerful than one and a half horsepower.

Threads with a metal core are like with round section and with sharp edges. Regardless of the type of cross-section, such threads are the best suited for overcoming mowing plants. Threads belonging to this type easily mow not only dry grass, but even small shrubs.

Threads with wire inside compare favorably with other types of consumables incredible durability. But unfortunately, this feature has a more than noticeable effect on the price of this type. The cost of threads with a core significantly exceeds the cost of threads of other types.

Thickness selection

In addition, special attention should be paid to the thickness of the consumable. For mowing young grass, a thread with a diameter within one and a half millimeters is suitable. The larger the diameter of the thread, the drier and coarser weeds it can overpower.

When choosing a fishing line by thickness there is one “but”. It is important not only to evaluate the capabilities of the material, but also to take into account the features of the trimmer. Necessary look in the user manual, which is attached to the tool and find information about the requirements for the cutting element.

Using the wrong thread may cause the tool to malfunction. Using a thread that is too thick will overload the motor of the device. And the use of too thin thread at times will increase the wear of the twisting mechanism.

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel it in the trimmer. When a suitable fishing line is found and acquired, you can begin to consider ways to wind it on a reel.

How to wind a line onto a trim reel

At first glance, refueling a fishing line into a tool reel is not an easy task. But it is enough to carefully study this process. and in the future, all necessary actions will be carried out without any difficulties.

To learn how to refill a fishing line with a trimmer, read this guide. The step-by-step instruction below takes into account the features of the coils of different types of trimmers, therefore applicable to any instrument.

So, the procedure is as follows.

  1. The fishing reel is the bottom end of the trimmer. First things first, of course, you need to remove this head from the device. To do this, fix the rod (or, in other words, the shaft) on which the coil is mounted. It is necessary to fix it in such a way that it does not scroll. It is easiest to do this by placing a kind of stupor (preferably metal) between the shaft thread through a special hole. When the shaft is locked, you can unscrew the coil.
  2. At this stage, the bobbin to attach the fishing line to is removed from the head. To do this, you need to disassemble the head into elements. To do this, you must first find the latch on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it with effort. Keeping the lock pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
  3. A tight spring is placed between the bobbin and the head. It needs to be temporarily set aside so that it does not interfere with the winding process. Before proceeding to the line of winding fishing line, it is necessary to inspect the bobbin. If it contains the remains of an old fishing line, they must be removed. When the bobbin is clean, you can begin preparing a new skein.
  4. It is necessary to measure and cut six (maximum. seven) meters from a previously prepared skein of new fishing line. The bobbin should be at hand.

At this point, actually begins the key stage, which this article is devoted to.

The first way to wind the line

The right amount of fishing line is cut off. Now you need to carefully inspect the bobbin, in order to understand what type it belongs to. It depends on how the line is to be wound on it.

There are two types of bobbins. In general, they are slightly different from each other. Regardless of the type, the coil is divided into two compartments. upper and lower. In the first type, the dividing face does not close into the ring and has a recess.

In the second type, it is solid, but near it on the sides on both sides there are small through holes. The method of winding the thread needs to be studied depending on which of the above types the coil belongs.

  • The previously prepared six-meter segment must be bent in half. It’s best not exactly in the middle, but in such a way that one half is about fifteen centimeters longer.
  • Then the place of the bend must be inserted into the recess in the dividing face. One half of the fishing line should be at the top of the reel, the other half at the bottom.
  • Now you can proceed directly to winding. You need to wind it in the direction that the arrow on the bobbin points. When winding, you need to hold the threads so that they do not intertwine and the upper half is wound into the upper part of the spool, and the lower half. into the lower part. Each half should remain free about fifteen centimeters from the end.
  • In the upper face of the bobbin there are small recesses (or, in other words, grooves) for fixing the consumable. The ends of the threads must be inserted into these recesses so that they are fixed one opposite the other.
  • The final stage of refueling consumables in the tool. the ends attached to the bobbin must be threaded into the corresponding holes in the trimmer head.
  • That’s all. The winding process is complete. Now it remains only to assemble the head into a single whole. The spring is carefully placed back between the bobbin and the head. Then you need to insert the bobbin into the head and press them together.
  • It is recommended that the loose ends of the thread be pulled outward. To do this, you need to take turns pulling the ends of the consumable so as to remove them from the grooves of the bobbin. You can make sure that the cutting element is removed from the retaining grooves by trying to pull the threads out a little. they should freely exit through the holes in the head.
  • While holding the bobbin down, put a cover over it. The cover must be screwed to the head so that all the grooves on their bodies are aligned and the bobbin remains fixed between them.
  • And finally, the most recent action. the head is screwed back into place at the bottom of the tool.

The process is completed. The line is tucked into a reel. The trimmer is ready for further work.

Second winding method

  • A previously prepared six-meter-long section, it is required to bend exactly in the middle and cut it. Thus, two segments of the same length are obtained.
  • At one end of each segment you need to make a small “hook”. To do this, it is necessary to bend a couple of centimeters from the edge and briefly fix it so that the “hook” does not bend.
  • Then one piece is taken. A “hook” is inserted into the through hole at the top of the bobbin.
  • Now you can proceed to the key stage. winding. The direction in which you want to wind is indicated by the arrow on the bobbin. It is important to ensure that the line is wound strictly within the top of the reel. Winding the thread to the very tip is not necessary. from the end should remain free about fifteen centimeters.
  • In the upper face of the coil there are small recesses (the so-called grooves) for fixing the consumable. The loose “tail” of the thread must be inserted into one of these recesses.
  • The top of the coil is tucked. Now you need to do the same procedure with the bottom. The second length of thread is taken. A “hook” is threaded through a hole in the bottom of the bobbin.
  • After that, you can begin to reel the fishing line (within the lower compartment). And at this stretch of free you also need to leave about fifteen centimeters from the end. This remaining “tail” must be inserted into the recess opposite to the one into which the end of the first segment is inserted.

The subsequent steps for this type of coil are exactly the same as those described for the previous type in steps five through nine.

This is how the fishing line in the trimmer coil changes. Nothing no complicated in the process. And after a few refueling completed, all actions will reach automatism.

To visually study the process described above, you can turn to the Internet for help. The popular YouTube portal has many different videos with a demonstration of winding fishing line on a trimmer reel.

How to reel a fishing line onto a trim reel. Walkthrough VIDEO

How to choose a fishing line. length, diameter, restrictions

IMPORTANT TO REMEMBER! Do not use fishing line or metal cables for the trimmer. Such a replacement is not effective and dangerous. A cable can injure not only the mower itself, but also others.

As for the length, it is worth counting on the estimated frequency of use of the trimmer. The more often, the more it is worth stocking up consumables.

Information on the possible diameter of the fishing line can be found on the hull. trimmer reels. Most likely, the range will be indicated there. Thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the features of the cultivated area. The larger the diameter, the easier it is to mow hard grass.

Preparation. remove and disassemble the spool

In most models of electric and gas trimmers, you need to remove the coil to replace the fishing line. The FUBAG tool allows you to skip this step. In order for the instruction to be universal, we will nevertheless consider it in detail:

1. Lock the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.

2. Unscrew the bobbin case. In our example, strictly in the clockwise direction.

3. Unscrew the cover in the direction indicated on the housing.

4. Take out the coil for winding.

The preparatory phase is over. You can proceed to winding fishing line.

How to wind a line onto a trim reel

Winding algorithm

2. Insert the resulting loop into the groove.

3. Lay the fishing line in the direction indicated on the element body.

4. Insert the short end into the groove on the side of the coil.

5. Fasten the long end in the opposite groove.

6. Place the reel with wound fishing line into the bobbin case.

7. Pull the fishing line out of the locking grooves.

8. Put on a cover and fix.

9. Trim the ends of the fishing line, leaving 10 to 15 centimeters.

Replacing the fishing line is completed and now it remains only to fasten the bobbin to the trimmer and you can work.

ATTENTION! Common fishing line problems

No wonder they say: "Forewarned is forearmed". Knowing about possible problems and the reasons for their occurrence, you can prevent them in a timely manner. We recommend remembering or leaving a memo.

How to Wrap Fishing Line On Trimmer Reel With Your Hands Properly – Consider Thoroughly

How to Wrap Fishing Line On Trimmer Reel With Your Hands Properly. Consider Thoroughly

Owners of private homes know how necessary this type of tool is, as a trimmer. It can be gasoline and electric, but they differ in the design of power units. To cut grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out during application, so how to wind the trimmer coil, we will consider in detail in the material.

What you need to know about fishing line for trimmer

A fishing line is a consumable that consists of nylon and serves as a cutting device. By means of this equipment, grass mowing occurs, which is ensured by rotating the tool head with high frequency. This material has a different thickness, which depends on its use on the corresponding tools, low-power electric (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with scythes (from 2.4 to 3 , 2 mm).

The more powerful the tool, the correspondingly thicker the cutting tool should be. This affects not only the quality of the grass mowing, but also the life of the material. If you are wondering how to wind the trimmer coil, then it’s time to change the reload tool. With the onset of spring, this issue becomes more and more popular, so it’s time to understand the step-by-step instructions for replacing the fishing line in the trimmer coil.

Types of Trimmer Heads for Coils

The main elements of the trigger is a mowing head, which is a cylindrical body with a coil (bobbin) inserted inside. The fishing line (cord) is refueled into it. The heads differ from each other in the way the cord is fed and refueled. There are three types of heads:

  • Automatic. Submission of fishing line is carried out after this, as the user reduces engine speed. Automatic feed of the cord is very convenient when you need to perform a large amount of work. The disadvantage of such a head is the high consumption of thread.
  • Semi-automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its work is arranged so that the fishing line begins to automatically lengthen at a time when the trimmer is working at full speed. It is only necessary to slightly hit the head of the apparatus on the ground (this will remove the blockage of the fishing line), and the cord will be pulled out of the bobbin due to centrifugal force. Then the fishing line is cut to the required length with a knife, which is located on the protective casing.
  • Manual To lengthen the cord, you must stop the device. After that, the fishing line will need to be pulled out manually.

Types of trim coils

How to remove the reel from the trimmer and remove the fishing line

Initially, before you put fishing line in the trimmer coil, you need to remove it from there. A coil or pickup is a device that is located inside the mowing head, bobbin or drum. The heads come in different types (depending on the manufacturers), however, the principle of replacing fishing line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

It is interesting! Tooling can be replaced directly on the tool, but if you are doing this for the first time, it is still recommended to remove the head and study the detailed winding process. After the technology has been mastered, you can perform replacement work on a trimmer trimmer or a brushcutter.

The instruction on how to unwind the manual head on the trimmer has the following form:

  1. Turn the tool upside down and, if necessary, clean it from contamination. Use two fingers of one hand to hold the cover latches (on the mowing head), which are located symmetrically to each other. After lightly pressing them inward, remove the protective cover from the drum
  2. Next, the fishing reel should be removed from the drum shaft. It is mounted on a shaft without fasteners, therefore it is dismantled with one hand
  3. The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with the appropriate tip or bit
  4. To unscrew it is necessary to hold the base of the drum with one hand, and the second to perform unscrewing with a screwdriver counterclockwise
  5. After that, you can proceed to dismantle. To do this, you do not need to pull it with all its strength, but slightly swaying to the sides, slowly disengage from the metal shaft on which the drum is mounted
  6. When reinstalling, put the head into the slots of the tetrahedral shape

This process is not difficult, and as you know, it is not necessary to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

  • Periodically removing the head is recommended to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even sometimes impossible
  • If the screw has a four-sided boring of the head, then a screwdriver or bits of the appropriate size should be selected for twisting to prevent the faces from licking on the head
  • When assembling the installation, treat the threaded seat with lubricants, for example, solid oil or machine oil
  • If the faces on the screw are licked, then you can use special clamping tongs to unscrew it
  • There are drums that do not require pre-disassembly. To dismantle them, grasp it and turn it clockwise in the opposite direction

Knowing how to disassemble the drum, you should continue to clarify the process of replacing the trimmer fishing line. The video below shows a detailed process on how to open the trimmer coil and disassemble it.

Fishing line selection

To ensure that the fishing line in the trimmer head is successful, it is important not to lose money with the choice of consumables. The thicker the cord you fill, the thicker and tougher the grass it can cut. Often used universal fishing line, the diameter of which is 2 mm. You can select the diameter suitable for the mower in the following ways:

  • See the line thickness information in the instructions that came with the trimmer.
  • Pay attention to the bobbin itself. Sometimes it displays information about the possible diameters of the fishing line.
  • Another option is to try inserting the cord into the outlet. If it easily passes into it, then the selected diameter of the fishing line is suitable for use.

Trimmer reel

Video: How to Wrap Fishing Line On Trimmer Reel With Your Hands Properly. Consider Thoroughly


You can pick up the cord by the type of engine. If the fishing line is too thick, the rotation resistance will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

  • For an electrical device with an engine less than 500 V, a thread 1.3 mm thick is suitable. If this was not found, then you can use a 1.6 mm fishing line. If the power is greater than 1 kW, then select a cord with a diameter of 2 mm.
  • For a gas trimmer, a shaft mower matters. For a bent version, a 2 mm cord is often used. If the shaft is straight, install a thread of 2.4–2.5 or 3 mm. The thickest fishing line is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross-section of the cord. Some popular options:

  • The most common fishing lines with a circular cross section. They mow fresh herbs well, but do worse with shrubs, dead trees.
  • Twisted (spiral) cord is not very strong, but not bad for thin young grass.
  • A serrated thread with sharp edges is ideal for large weeds in a neglected area.
  • You can even mow the lawn with a rectangular, star or square fishing line for a trimmer, but they are not very durable.
  • The most durable is a two-component cord with an inner core and a round cross-section.

Types of fishing line for trimmer

Please note that instead of fishing line, wire, metal strings and cables, as well as ordinary fishing thread, cannot be used. The device will be dangerous for both the user and others. So the cable or similar products will gradually start to work, as a result, their ends will unravel, and small pieces will fly apart at high speed.

How does the head with fishing line on the Lawn Mower work? Why do you need to know the principle of operation

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a clamping spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble a trimmer head without a spring, i.e. on a manual type head. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the above described instructions.

The principle of operation of the semi-automatic trimmer coil is as follows:

  1. Inside the head is a coil that is seated on the slots, preventing its free movement
  2. A spring acts on the coil, which presses it against the slots in the cover structure
  3. A line is wound around the tip, the length of which depends on the tool itself. Usually this length is from 1 to 4 meters
  4. During the execution of the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum is clamped, whereby it disengages from the slots. In this case, the fishing line is wound off the drum, increasing in length
  5. After releasing the required amount of fishing line, you should release the pressing, and continue to work on the cutting of grass

The advantage of a fishing line tool is that this consumable material does not require sharpening compared to metal discs. In addition, if there is a stone or a tree on the way, the line simply comes off, without adversely affecting the gearbox and the tool motor, as is the case with metal cutting discs.

Knowing the design and arrangement of the types of mowing or trimmer heads, it is necessary to go on to consider the process of refueling fishing line into the trimmer coil. Indeed, it is this moment that causes the majority of owners of special tools difficulties.

Winding fishing line on trimmer

The measured and accurate dismantling of the spool from the spit reel makes it possible to go directly to the winding of the fishing line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of reels, depending on the number of antenna line fishing line and methods of refueling:

  1. Trimmer head with one working antennae;
  2. A bobbin with two antennae fishing line;
  3. Auto winding reel.

Single-Barrel Trimmer Coil

Single-mustache coil brush

Many owners and specialists note the simplicity of operation and refueling reels with one mustache. Depending on the manufacturer, the length of the fishing line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and winding is made in the direction opposite to the working rotation of the bobbin. Most coils on the outside of the case have marks in the form of arrows that indicate the direction of movement of the trimmer bobbin.

After winding, you need to leave a free end of 15-30 cm to enhance centrifugal force, which is crucial when removing the trimmer line in automatic and semi-automatic reels. We pass the left end through the working hole of the coil and assemble the head.

Double Antenna Trimmer

Two groove head

After removing the spool from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but with careless refueling in a twin groove, there are problems with operation. Due to the likelihood of weaving adjacent tool strings, a situation may arise when it is impossible to remove new ones after wear of the working antennae.

Regardless of the number of streams for refueling, a fishing line from 1.5 to 3 meters long is taken. Winding must be done in the direction opposite to the rotation of the head, since winding in the direction of travel will cause the line to not be removed from the reel. After the fishing line is tucked into the trimmer coil, free ends (15-30 cm) are threaded through special holes. Next, we collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the guard will cut off the excess.

Trimmer head with automatic threading

Types of Trimmer Heads

In some models available on the market, a reel with an automatic winding mechanism is installed. It is enough for the owner to correctly tuck and fix the ends in the head, and the tool itself will perform the winding operation when it is switched on in the operating mode. It is almost impossible to wind a fishing line into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of an automatic trimmer head include the ease of refueling fishing line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

Instructions with a step-by-step description of how to wind the trimmer coil and the brushcutter

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head, and look at the side wall of the reel. This information is usually presented on a tip that will not allow you to make a mistake with the use of appropriate equipment.

If the information on the reel about what diameter the fishing line can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the snap, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of motokos and trimmers you use, you decide on your own which option is suitable.

It is interesting! The principle of how to wind a fishing line on a motor-scythe tip is appropriate not only for autonomous petrol units, but also for electric trimmers.

Video

Method 2. how to properly put fishing line on a motor-scythe reel with a photo description and video

The second method differs from the first in that not a single piece of equipment is charged into the coil, but segments of two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two pieces of fishing line into the tip of the brushcutter is the same with the first method, and to make sure of this, below is a detailed instruction:

  1. There are two equal lengths of material that can be used.
  2. One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with the help of which the fishing line will be fixed
  3. Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half.
  4. Brace fishing line should catch on the bracket, and make it winding in the direction of the arrow
  5. The tooling is wound up until a segment of 10-15 cm remains, which is fixed in the corresponding hole on the side of the tip
  6. Similarly, the manipulation of the second end of the fishing line
  7. The tabs start up in the holes of the head, and then, removing the snap-in from the temporary fasteners in the coil, a cover with latches is installed

The above instructions on how to install a scaffold in a Lawn Mower will help not only correctly, but also quickly perform the replacement procedure. Assembly of the trimmer coil, as mentioned above, can be performed without removing the head, but in this case you will need to conveniently fix the tool. Video instruction is presented below.

Tips and tricks on how to wind a fishing line and what you need to know

There are some useful tips and tricks that will be useful to learn not only for beginners, but also for experienced mowers. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations read as follows:

  1. Install the cover until it clicks. over, this is 2 or more clicks, which depends on the number of clips. If one latch does not snap in, then when you start the tool, the drum may pop out and injure a person
  2. Do not wrap the fishing line with a strong pulling it, as well as in an amount greater than you can insert it into place. It’s better not to wring the snap than it will be more, as this will lead to negative consequences in the form of the inability to unwind it if necessary
  3. If you own a tool not with two leads of the fishing line, but with one (usually these are low-power units), then the winding process is carried out in the same sequence as described above, only with the difference in the absence of a middle rim between the extreme bases of the coil
  4. After replacing the material, it is necessary to first check the operability of the tool, and only then proceed to mowing the grass. If you do not perform a preliminary check, then the forest can unwind and injure a person

It is interesting! Choose material of the appropriate quality so as not to get injured when working with petrol scythes, trimmers and scythes. In the process of mowing grass, small stones and other materials fall under the rotating parts, which can fly off over long distances, therefore, despite the fact that the fishing line is not a knife, work with the tool should be carried out in protective special uniform.

The result of the work done is the following. after the replacement of new material, the usual one is enough for an area of ​​up to 600 square meters, but taking into account the presence of a reinforcing layer on the fishing line. Conventional nylon materials serve less, which is important to consider when working. Do not try to mow thick-stemmed grass with fishing line, as there are special metal discs or knives for this.

How to Wrap Fishing Line On Trimmer Video Correctly

We wind the fishing line on the trimmer reel

Owners who have their own household plots often encounter the problem of keeping a lawn, namely, the need for high-quality mowing of grass. For these purposes, either a manual or an electric braid is used. a trimmer (see photo). It is clear that working with the electric model is much easier and faster. The grass is mowed using a fishing line rotating at high speeds. But during operation, the thread wears out over time and requires a change. So how do you rewind the fishing line on the trimmer reel with your own hands?

How to Wrap Fishing Line On Trimmer Video Correctly

Types of fishing line

The thread for the trimmer can be divided into types according to its diameter. It can begin with the smallest. 1.2 millimeters and reach up to 4 millimeters. The most commonly used is a diameter of 2 millimeters. But it is necessary to select it strictly individually, based on the specific model of the device. Often the required diameter of the product is indicated in the passport on the product. Usually the more powerful the trimmer, the larger the diameter of the fishing line should be. For example, it is best to wind a thread with a diameter of 2.4 millimeters on a coil of a Lawn Mower, and for a product with a weak engine, a thread diameter of 1.6 millimeters is suitable.

Fishing lines differ in type of section. It can be round (for mowing ordinary grass), square (for soft and often mowed grass), with sharp edges (for tall grass), with notches (for thin grass), and also complex (see photo). The latter can not be filled in all types of devices. It should be noted that the line is intended solely for mowing grass. To cope with other types of plants, it is necessary to use a Lawn Mower with a sharp knife. The length of the threads that can be tucked into the trimmer can range from 10 to 100 meters.

Video: How to Wrap Fishing Line On Trimmer Video Correctly


How to wind a line onto a trim reel

Spools of products may have different filing systems. This can be manual, semi-automatic or automatic feed. Depending on this, it is necessary to wrap the fishing line. So how do you thread a bobbin? To begin with, the cap is unscrewed on the coil (see video). If the thread on it is left-handed, then you need to turn it clockwise, and not as usual.

Such a thread is made so that during the operation of the product the trimmer head cannot unwind. To fill the thread will require about 5 meters of material (see photo). It must be folded strictly in half, insert the center into the space provided on the device and wind it in the direction of the arrow, which should be drawn on the reel, as in the video. After that, you just need to tighten the cap.

A car battery (battery) is a battery for storing and storing electric energy for the purpose of its further use. Namely for: launch.

Many motorists and motorists prefer at least a little, but to understand their own technology. This desire is fully justified. not only that.

How to replace a fishing line in any trimmer

Technological progress provides us with many opportunities to get rid of manual labor. Among other things, this includes grass mowing, which, when using an ordinary scythe, required a lot of physical energy. In modern conditions, this process is greatly facilitated, because Applied technology minimizes all costs. Devices such as electric and gas trimmers have firmly taken the place of indispensable assistants in gardening. Mowing grass with their help has become more fun than hard and grueling work.

Structurally, the trimmer consists of an engine, a rod and a working body, which, depending on the mowed vegetation, is either a mowing head or a disk mill. And if everything is more or less clear with a milling cutter, sometimes questions arise with a nozzle. As a rule, they appear when the line ends.

How to wrap fishing line on a reel? We understand.

So, first unscrew the nozzle. Do this by rotating the drum to the right. Here we have a drum in our hands with the remains of an old fishing line. We open it. Most often, the lid closes with latches, which can be opened with a screwdriver by threading it through the holes and pressing lightly. Or you need to squeeze the lock and turn the cover in the direction of the arrow. In this case, the lid itself must be kept, as in drums with automatic supply of fishing line there is a spring, which, when straightened, can throw out all the internal parts of the drum. Gently pulling out the reel, we remove scraps of fishing line from it.

Now you need to take 5 meters of new fishing line and fold in half (to find the middle). In the middle part of the reel there is a recess (in some designs. a hole), for which we need to hook our fishing line. There is also an arrow on the reel showing the direction of winding. An important detail. if the reel has two compartments, then one half of the fishing line should be wound in one direction, and the other in the other. Finishing the winding, you need to leave 15-20 cm of fishing line free. There are also two recesses on the upper ring of the coil through which these free ends must be drawn. We coped directly with the winding itself.

The last step in the fishing line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the fishing line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, pulling the fishing line and trying not to displace the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort so that the latches fall into place. Voila! The mowing nozzle is ready to go!

How to Wrap Fishing Line Coil Trimmer Correctly?

How to Wrap Fishing Line Coil Trimmer Correctly?

Despite the fact that gardening equipment has been used for a long time, for some owners of private houses it is still a novelty. That is why often questions arise about how to properly wind a line on an electric or gas trimmer.

This is essentially a simple operation, but all its stages must be performed correctly to achieve the desired result. over, in the operating instructions, only a few manufacturers give an answer to this urgent question. Study the article and find out how the line is wound around the reel of the trimmer.

The procedure for winding fishing line on the trimmer reel

First of all, you should know that trimmers have different working nozzles. The reel can be designed for different lengths and thicknesses of fishing line. this point should be considered when purchasing supplies.

So, how do you charge the fishing line into the trimmer coil? All work is divided into several stages:

  1. First you need to disassemble the trimmer head.
  2. Unscrew the nozzle by rotating the drum to the right.
  3. Press your fingers on the two latches located on opposite sides of the slots, and remove the top cover of the nozzle. You can pry the cover with a screwdriver. This should be done carefully: the reels with automatic line feed have a spring, which can forcefully drop the lid along with all the contents of the reel.

Video: How to Wrap Fishing Line Coil Trimmer Correctly?


When you turn on the trimmer, the excess fishing line will be cut off by the cutting blade itself.

As you can see, it is easy to wind the line onto the reel of the trimmer: the main thing is to do everything right. And here are some more tips that will be useful to you when choosing a fishing line, its winding and subsequent work:

  • fishing line is of different thickness and with different cross-section. The best option for winding is the "native" for this model of fishing line;
  • Never use a fishing line or metal cables for the trimmer. Such a replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure not only the lawn mower, but also others;
  • the fishing line is cut off when the working trimmer comes into contact with solid objects. Try not to allow this, otherwise you will have to stop every time, turn off the device and rewind the fishing line onto the reel;
  • Use a straight line for mowing grass and a pigtail line for coarse weeds. It is more durable and will not be permanently cut.

Wrap Fishing Line On Trimmer Coil

Owners who have their own household plots often encounter the problem of keeping a lawn, namely, the need for high-quality mowing of grass. For these purposes, either a manual or an electric braid is used. a trimmer (see photo). It is clear that working with the electric model is much easier and faster. The grass is mowed using a fishing line rotating at high speeds. But during operation, the thread wears out over time and requires a change. So how do you rewind the fishing line on the trimmer reel with your own hands?

Wrap Fishing Line On Trimmer Coil

Types of fishing line

The thread for the trimmer can be divided into types according to its diameter. It can begin with the smallest. 1.2 millimeters and reach up to 4 millimeters. The most commonly used is a diameter of 2 millimeters. But it is necessary to select it strictly individually, based on the specific model of the device. Often the required diameter of the product is indicated in the passport on the product. Usually the more powerful the trimmer, the larger the diameter of the fishing line should be. For example, it is best to wind a thread with a diameter of 2.4 millimeters on a coil of a Lawn Mower, and for a product with a weak engine, a thread diameter of 1.6 millimeters is suitable.

Video: Wrap Fishing Line On Trimmer Coil


Fishing lines differ in type of section. It can be round (for mowing ordinary grass), square (for soft and often mowed grass), with sharp edges (for tall grass), with notches (for thin grass), and also complex (see photo). The latter can not be filled in all types of devices. It should be noted that the line is intended solely for mowing grass. To cope with other types of plants, it is necessary to use a Lawn Mower with a sharp knife. The length of the threads that can be tucked into the trimmer can range from 10 to 100 meters.

How to wind a line onto a trim reel

Spools of products may have different filing systems. This can be manual, semi-automatic or automatic feed. Depending on this, it is necessary to wrap the fishing line. So how do you thread a bobbin? To begin with, the cap is unscrewed on the coil (see video). If the thread on it is left-handed, then you need to turn it clockwise, and not as usual.

Such a thread is made so that during the operation of the product the trimmer head cannot unwind. To fill the thread will require about 5 meters of material (see photo). It must be folded strictly in half, insert the center into the space provided on the device and wind it in the direction of the arrow, which should be drawn on the reel, as in the video. After that, you just need to tighten the cap.

A correctly selected anatomical mattress is the key to health and comfortable sleep. Its main task is to provide proper support for the spine during.

It is difficult to imagine a simpler and absolutely healthy way of cooking food than cooking with an electric grill. Thanks to the unique device.

1 2